JETWAY 626EMP Series User manual

626EMPxxx/626EMWxxx
V626EMPxxx/V626EMWxxx
(Serial Motherboard)
USER'S MANUAL
M/B For VIA BravoGiga processor
NO. G03626EMWR208
Rev:2.0
Release date: July 2005
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
USER’S NOTICE.....................................................................................................................ii
MANUAL REVISION INFORMATION..............................................................................ii
THERMAL SOLUTIONS.......................................................................................................ii
CHAPTER 1 INTRODUCTION OF MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD..........................................................................1
1-2 SPECIFICATION .....................................................................................................2
1-3 LAYOUT DIAGRAM & JUMPER SETTING ......................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS................................................................5
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING......................................5
2-3 GLOSSARY...............................................................................................................7
2-3-1 SETTING CPU BUS CLOCK & MEMORY CLOCK JUMPER............8
2-3-2 OVER CLOCK RUNNING..........................................................................8
2-4 INSTALL MEMORY ...............................................................................................9
2-5 EXPANSION CARDS...............................................................................................10
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION..................10
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD............................................10
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD..........11
2-6 CONNECTORS, HEADERS....................................................................................11
2-6-1 CONNECTORS.............................................................................................11
2-6-2 HEADERS......................................................................................................14
2-7 STARTING UP YOUR COMPUTER.....................................................................17
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP..................................................................................................18
3-2 GETTING HELP.......................................................................................................19
3-3 THE MAIN MENU ...................................................................................................19
3-4 STANDARD CMOS FEATURES............................................................................21
3-5 ADVANCED BIOS FEATURES .............................................................................22
3-6 ADVANCED CHIPSET FEATURES .....................................................................24
3-6-1 DRAM TIMING SETTING..........................................................................25
3-6-2 AGP TIMING SETTINGS ...........................................................................26
3-6-3 PCI TIMING SETTINGS.............................................................................26
3-7 INTEGRATED PERIPHERALS.............................................................................26
3-7-1 ONCHIP IDE FUNCTION...........................................................................27
3-7-2 ONCHIP DEVICE FUNCTION...................................................................28
3-7-3 ONBOARD SUPER IO FUNCTION...........................................................29
3-8 POWER MANAGEMENT SETUP.........................................................................30
3-8-1 WAKE UP EVENTS .....................................................................................31
3-9 PNP/PCI CONFIGURATION SETUP ...................................................................32
3-10 PC HEALTH STATUS............................................................................................33
3-11 MISCELLANEOUS CONTROL............................................................................33
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS ..................................................34
3-13 SET SUPERVISOR/USER PASSWORD..............................................................34
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 95/98/98SE/NT4.0/2000 .........................35
4-1 VIA 4 IN 1 INSTALL VIA SERVICE PACK 4 IN 1 DRIVER.............................36
4-2 VGA INSTALL VIA VGA DRIVER ..........................................................37
4-3 SOUND INSTALL ALC/CMI AUDIO DRIVER.............................................38
4-4 LAN INSTALL VIA LAN CONTROLLER DRIVER................................41
4-5 USB2.0 INSTALL VIA USB2.0 DEVICE DRIVER........................................41
4-6 PC-CILLIN INSTALL PC-CILLIN 2005 ANTI-VIRUS PROGRAM....................42
4-7 HOW TO DISABLE ON-BOARD SOUND............................................................43
4-8 HOW TO UPDATE BIOS........................................................................................43
TABLE OF CONTENT

ii
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD AND WE DO
ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 Second Edition July 2005
Item Checklist
5Motherboard
5Cable for IDE/Floppy
5CD for motherboard utilities
□Cable for USB Port 2/3 (Option)
5User’s Manual
□Cable for COM2 Serial Port (Option)
□Cable for S-Video/RCA Composite TV-Out (Option for 626EMWxxx/V626EMWxxx)

1
Chapter 1
Introduction of 626EMPxxx/626EMWxxx/V626EMPxxx/
V626EMWxxx Motherboard
1-1 Feature of motherboard
The 626EMPxxx/626EMWxxx/V626EMPxxx/V626EMWxxx motherboard is design for use
VIA new generation C3 processors, which embedded EBGA VIA C3 processor on board and
the memory size expandable to 2GB.(The –xxx indicate the CPU Frequency)
The motherboard uses the newest VIA VT8623 (CLE266) SMA (Share Memory Architecture)
North bridge chipset and VT8235 south bridge chipset. These motherboards support VIA C3
processors whose 133MHz front side bus & 133MHz memory interface delivers a clear
upgrade path to the future generation of 133MHz processors and DDR266 DRAM memory. It
offers ULTRA DMA 133MB/sec (ATA 133) to provide speedier HDD throughout that boosts
overall system performance.
For these motherboards, with integrated 3D Graphic Acceleration, makes this board lower cost
alternative to a video card. The motherboard also integrated VIA VT6103 LAN-PHY
Controller supports 10/100 BASE-T Transfer rate for those whom require faster LAN function
for net work. 626EMWxxx/V626EMW embedded VIA VT1622A TV Encoder provide S-
Video/ Composite connector support NTSC/PAL system signal output.
V626EMPxxx/V626EMWxxx integrated PCI 6-Channel Audio Controller on board support
6-channel Audio function, which is fully compatible with Sound Blaster Prothat gives you
the best sound quality and compatibility.
626EMPxxx/626EMWxxx integrated AC’97 2.2 CODEC on board support 6-channel Audio
function, which is fully compatible with Sound Blaster Prothat gives you the best sound
quality and compatibility. With 2 USB controller as well as capability of expanding to 6 USB
connectors compliant to USB2.0 provided 480Mb/sec data transfer rate, which guarantees this
board to meet future USB demand. Moreover, these motherboards had built-in hardware
monitor function that capable of monitor and protect your computer.
This motherboard provides high performance & meets future specification demand. It is
really wise choice for your computer.

2
1-2 Specification
Spec Description
Design ∗Micro ATX form factor 4 layers PCB size: 24.4x19.0cm
Chipset ∗VIA VT8623 SMA (Share Memory Architecture) North Bridge
∗VIA VT8235 South Bridge
Clock Generator ∗ICS 950908 Clock Generator
∗Support 66/100/133MHz system Bus Clock (CPU Bus Clock)
∗Support CPU Frequency step by step setting in BIOS Setup
∗Support 100/133 MHz system Memory clock
∗Support 33MHz PCI Bus clock
CPU ∗Embedded VIA C3 EBGA processor
Memory Socket ∗184-pin DDRDIMM socket x2
∗Support DDR200/DDR266 DDR memory
∗Expandable to 2GB(512Mb x8/x16 DRAM technology)
Expansion Slot ∗32-bit PCI slot x4 PCI-2.2 compliant
Integrate VGA
∗Integrate 2D/3D graphic Engines
∗8/16/32/64MB frame buffer using system memory
∗Internal AGP 8x performance
∗Support 24-bit 250MHz RAMDAC
TV-Out
(for 626EMWxxx
V626EMWxxx)
∗VIA VT1622A TV Encoder
∗Provided S-Video/Composite output for NTSC/PAL system
Integrate IDE ∗2 channel of Bus Master IDE port supporting ULTRA DMA
33/66/100/133 mode devices
Integrate LAN
∗Integrated VIA VT6103 LAN-PHY Controller
∗Support 10/100 BASE-T Transfer rate
Audio ∗AC’97 6-channel Audio CODEC on board for
626EMPxxx/626EMWxxx
∗CMI 8738-6CH PCI Audio controller integrated for
V626EMPxxx/V626EMWxxx
∗Support 6-channel audio function, fully compliant to Sound
Blaster Pro
∗Audio driver and utility included
BIOS ∗Award 2Mb Flash ROM
Multi I/O ∗PS/2 keyboard and PS/2 mouse connectors
∗Floppy disk drive connector x1
∗Parallel port x1, Serial port x2
∗USB 2.0 connector x2
∗USB 2.0 headers x4 (connecting cable option)
∗Audio connector (Line-in, Line-out, MIC, GAME)

3
1-3 Layout Diagram & Jumper Setting
GAME/MIDI PORT
VGACOM1
PS/2 MOUSE
PS/2 Keyboard
USB
LINE-OUT
LINE-IN
MIC
PRINTLAN
VIA VT6103 LAN-PHY
Controlle
r
Front Panel Audio 2Mbit Flash ROM BIOS
VIA C3 EBGA CPU
DIMM Socket X2
Floppy Connector
VIA VT8623(CLE266) Chip
ATA 100 IDE Connector
Front Panel Connector
ATX Power Connector
CPU FAN
VIA VT8235 Chip
IR Connector
SFAN
VIA VT1211 I/O Chip
Clear CMOS (JP6)
Speaker Connector
Power LED Connector
USB Port
(USB1, USB2)
PC99 Back Panel
K/B Power ON Jumper
(JP1)
COM2 Connector
PS2 KB/Mouse Port
USB Port
/
LAN Connector
TV OUT Connector
VIA VT1622A Chip
6CH Audio Codec
(for 626EMP/626EMW)
PCI Slot
USB Power ON Jumper (JP8)
6CH PCI Audio Chip
(for V626EMP/V626EMW)
On Board Sound Chip Jumper (JP7)
(for V626EMP/V626EMW)
CD Audio

4
Jumpers
Jumper Name Description Page
JP1 Keyboard Power ON Function Setting 3-pin Block p.5
JP8 USB Power On Function Setting 3-pin Block p.5
JP6 CMOS RAM Clear Function Setting 3-pin Block p.6
JP7
On board Sound Chip Enabled/Disabled
(for V626EMWxxx/V626EMPxxx) 3-pin Block p.6
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block p.11
KB/MS1 PS/2 Mouse & PS/2 Keyboard Connector 6-pin Female p.11
UL_B1 USB Port Connector 4-pin Connector p.12
LAN LAN Connector RJ45 Connector p.12
LPT Parallel Port Connector 25-pin Female p.12
VGA VGA Port Connector 15-pin Female p.12
COM1 Serial Port Connector 9-pin Connector p.12
CN2 Line-Out/Line-In/MIC Audio Connector Phone Jack p.12
FDD Floppy Driver Connector 34-pin Block p.12
IDE1 Primary IDE Connector 40-pin Block p.13
IDE2 Secondary IDE Connector 40-pin Block p.13
Headers
Header Name Description Page
COM2 COM2 Serial Port Headers 10-pin Block p.14
TV_OUT
(for 626EMWxxx/
V626EMWxxx)
S-Video/RCA Composite TV-out
Header
5-pin Block p.14
AUDIO Line-Out/MIC output Header 9-pin Block p.14
USB1/USB2 USB2.0 Port Headers 10-pin Block p.15
HD_LED Hard drive LED connector 3-pin Block p.15
RESET Reset switch lead 2-pin Block p.15
SPEAK Speaker connector 4-pin Block p.15
PWR LED Power LED Headers 2-pin Block p.15
PWR BTN Power Button Headers 2-pin Block p.15
CPUFAN, SFAN FAN Headers 3-pin Block p.16
IR IR infrared module Headers 5-pin Block p.16
CDIN CD Audio-In Headers 4-pin Block p.16
Expansion Sockets
Socket/Slot Name Description Page
DDR, DDR2 DDR SDRAM Module
Socket 184-pin DDR SDRAM Module Expansion Socket p. 9
PCI1~4 PCI Slot 32-bit PCI Local Bus Expansion slots p.10

5
Chapter 2
Hardware installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) Keyboard Power On function Enabled/Disabled (3-pin): JP1
When setting Enabled you can using keyboard by key in password to power on system.
Keyboard Power On Setting
2-3 closed K/B Power ON Enabled
JP1 1
3
JP1 1
3
1-2 closed K/B Power ON Disable
(Default)
(2) USB Power On function Enabled/Disabled (3-pin): JP8
When setting Enabled you can using USB Device to power on system.
1-2 closed USB Power On Disabled (Default)
2-3 closed USB Power On Enabled
JP8
13
JP8
13

6
(3) CMOS RAM Clear (3-pin): JP6
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JP6 to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JP6 and short pins 2-3 for a few seconds
4. Return JP6 to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
(4) On board Sound Chip (3-pin): JP7 (for V626EMPxxx/V626EMWxxx only)
On Board Sound Chip Setting
2-3 closed Sound Enabled (Default)
JP7 1
3
JP7 1
3
1-2 closed Sound Disable
CMOS RAM Clear Setting
2-3 closed Clear CMOS
JP6 13 JP6 13
1-2 closed Normal (Default)

7
2-3 Glossary
Chipset (core logic) - two or more integrated circuits which control the interfaces between the
system processor, RAM, I/O devises, and adapter cards.
Processor socket - the socket used to mount the system processor on the motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "Central Processing Unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"
Front Side Bus Frequency - The working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache - The flash memory inside the CPU, normally Pentium III CPU has 256K or
above, while Celeron CPU will have 128K.

8
2-3-1 Setting CPU Bus Clock & Memory Clock Jumper
Setting the front side bus frequency and SDRAM frequency
The motherboard uses jumper less function for the front side bus frequency and SDRAM
frequency users don’t need setting any jumper when plug the CPU in motherboard
For experience user looking for over clocking possibility, please refer to sec 2-3-2.
2-3-2 Over clock Running
WARNING! This section is for experienced motherboard installer only. Over clocking
can result in system instability or even shortening life of the processor.
Users can choose over clock running by BIOS CMOS SETUP UTILITY. When you entered
CMOS SETUP UTILITY, choose “Miscellaneous Control” you will see the screen as below
then. Phoenix – AwardBIOS CMOS Setup Utility
Miscellaneous Control
Item Help
VIA C3 Clock Ratio Default
Auto Detect PCI/DIMM Clock Enabled
Spread Spectrum Disabled
** Current Host/PCI Clock is
Host/PCI Clock at Next Boot is 100
** Current DRAM Clock is 133MHz **
DRAM Clock at Next Boot is 133MHz
+2.5V Select 2.65V
Menu Level >
↑↓→← Move Enter:Select Item +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
WARNING! The Design of this motherboard follows chipset and CPU vender’s design
guideline. Any attempts to push beyond product specification are not
recommended and you are taking your own risk to damage your system or
important data. Before over clocking, you must make sure your
components are able to tolerate such abnormal setting, especially CPU,
memory, hard disks, and VGA cards.

9
2-4 Install Memory
This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 64MB to maximum
memory size of 2.0GB DDR SDRAM.
Valid Memory Configurations
Bank 184-Pin DIMM PCS Total Memory
Bank 0, 1 (DDR1) DDR200/DDR266
DDR SDRAM Module X1 64MB∼1.0GB
Bank 2, 3 (DDR2) DDR200/DDR266
DDR SDRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 2.0GB) 2 64MB∼2.0GB
Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer
to figure 2-4 to see what a 184-Pin DDR200/DDR266 DDR SDRAM module looks like.
DDR2 (BANK2+ BANK3) DDR1 (BANK0+ BANK1)
NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be
locked into the DIMM module very firmly and fit into its indention on both sides.
WARNING! For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266-compliant DDR
Modules. When this motherboard operate at 133MHz, most system will not even
boot if non-compliant modules are used because of the strict timing issues, if your
SDR Modules are not DDR266-compliant, set the DDR SDRAM clock to 100MHz
to ensure system stability.
Figure 2-4

10
2-5 Expansion Cards
WARNING! Turn off your power when adding or removing expansion cards or other system
components. Failure to do so may cause severe damage to both your motherboard
and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.

11
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1 √
Slot2 √
Slot3 √
Slot4 √
Onboard VGA √
Onboard USB √
Onboard USB 1 √
Onboard USB 2 √
LAN √
AC97/MC97 √
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared
IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between
the two PCI groups that will make the system unstable or cards inoperable.
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.
(2) PS/2 Mouse & PS/2 Keyboard Connector: KB/MS1
If you are using a PS/2 mouse, you must purchase an optional PS/2 mouse set which
connects to the 5-pins block and mounts to an open slot on your computer’s case.
Pin 1
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V

12
(3) USB Port connector: UL_B1
The connectors are 4-pins connector that connect USB devices to the system board.
(4) LAN Port Connector: LAN
These connectors are standard RJ45 connector for Network supports 10/100 BASE-T
transfer rate.
(5) Parallel Port Connector (25-pin female): LPT
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-
board Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(6) CMO1 Connector (9-pin male): COM1
COM1 Connector is a 9-pin D-Subminiature Receptacle connector.
This connector is for connection Serial Device with cable.
(7) VGA Connector (15-pin female): VGA
VGA Connector is a 15-pin D-Subminiature Receptacle connector.
This connector is for connection Monitor and System to display.
(8) Audio Connector: CN2 (Line-Out/ Line-IN/ MIC, GAME)
This Connector are 3 phone Jack for LINE-OUT/ LINE-IN/ MIC.
Line-out : Audio output to speaker
Line-In : Audio input to Audio controller
MIC : Microphone Connector
Game: Game/Midi Port Connector
(9) Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to the floppy drives.
PS/2
Keyboard COM1 VGA
PS/2
MOUSE
USB LINE-OUT
LINE-IN
MIC
PRINT GAME/MIDI PORTLAN

13
Pin 1
Floppy Drive Connector
(10) Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s).
If you install two hard disks, you must configure the second drive to Slave mode by
setting its jumpers accordingly. Please refer to the documentation of your hard disk for
the jumper settings.
(11) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two
hard disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Pin 1
IDE2
Pin 1
IDE1
•Two hard disks can be connected to each connector. The first HDD is referred to as the
“Master” and the second HDD is referred to as the “Slave”.
•For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM
drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.

14
2-6-2 Headers
(1) COM2 Serial Port Headers (9-pin) : COM2
This board has one serial port header COM2, it come with cable providing serial port
COM2. The On-board serial port can be disabled through BIOS SETUP. Please refer to
Chapter 3 “INTEGRATED PERIPHERALS SETUP“ section for more detail information.
(2) TV-Out Header (5-pin): TV_OUT (for 626EMWxxx/V626EMW only)
The TV-Out header is for S-Video/Composite TV-Out function. With optional Cable
users can connect the TV and computer for TV-out function.
TV-OUT Header
TV_OUT
Pin 1
2
56
(3) Line-Out, MIC Header (9-pin): AUDIO
This header connect to Front Panel Line-out, MIC connector with cable.
Line-Out, MIC Headers
A
UDIO
Pin 1
AUD-MIC
AUD-FPOUT-L
AUD-MIC-BI AS
AUD-FPOUT-R
HP-ON
AUD-GND
AUD-RET-L
AUD-RET-R
AUD-VCC
2
910
COM2
Pin 1
Note: Orient the read marking on the
COM2 ribbon cable to pin 1

15
(4) USB Port Headers (10-pin) : USB1/USB2
These headers are used for connecting the additional USB port plug. By attaching an
option USB cable, your can be provided with two additional USB plugs affixed to the
back panel.
USB Port Headers
Pin 1
USB1/USB2
VCC
-DATA
GND
+ DATA
VCC
OC
-DATA
GND
+ DATA
(5) IDE Activity LED: HD_LED
This connector connects to the hard disk activity indicator light on the case.
(6) Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the lift of the system’s power supply. See the figure
below.
(7) Speaker connector: SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(8) Power LED: PWR LED
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.
(9) Power switch: PWR BTN
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.
System Case Connections
SPEAK
SPKR
GND
NC
VCC5
Pin 1
JW_FP
Pin 1
HDLED
RESET
VCC5
GND
VCC5 ACPILED
PWRBTN
PWRBTN
ACPILED
HDDLED
RSTSW
NC GND
PWRLED
Pin 1

16
(10) FAN Speed Headers (3-pin) : CPUFAN, SFAN
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the
fan manufacturer, the wire and plug may be different. The red wire should be positive,
while the black should be ground. Connect the fan’s plug to the board taking into
consideration the polarity of connector.
CPUFAN 13
SFAN
13
(11) IR infrared module Headers (5-pin) : IR
This connector supports the optional wireless transmitting and receiving infrared
module. You must configure the setting through the BIOS setup to use the IR function.
IR infrared module Headers
IR
Pin 1
GND
IRRX
NC
VCC
IRTX
2
5
6
(12) CD Audio-In Headers (4-pin) : CDIN
CDIN is the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-
Audio output connector.
CD Audio-In Headers
CDI N 4 1

17
2-7 Starting Up Your Computer
1. After all connections are made, close your computer case cover.
2. Be sure all the switch are off, and check that the power supply input voltage is set to
proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.
3. Connect the power supply cord into the power supply located on the back of your system
case according to your system user’s manual.
4. Turn on your peripheral as following order:
a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply
and press the ATX power switch on the front side of the case.
5. The power LED on the front panel of the system case will light. The LED on the monitor
may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.
If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.
Beep Meaning
One short beep when displaying logo No error during POST
Long beeps in an endless loop No DRAM install or detected
One long beep followed by three short
beeps Video card not found or video card memory bad
High frequency beeps when system is
working CPU overheated
System running at a lower frequency
6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in
BIOS SETUP.
7. Power off your computer: You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click “Start” button, click “Shut down” and then click “Shut down the computer?”
The power supply should turn off after windows shut down.