JETWAY 865GDMC User manual

865GDMC/865GDMCP
865PEDMC/865PEDMCP
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-865GDMC
Rev:1.0
Release date: November 2003
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
USER’S NOTICE .......................................................................................................................ii
MANUAL REVISION INFORMATION.......................................................................................ii
COOLING SOLUTIONS ............................................................................................................ii
CHAPTER 1 INTRODUCTION OF 865GDMC/865GDMCP/865PEDMC/865PEDMCP
MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD................................................................................1
1-2 SPECIFICATION.........................................................................................................2
1-3 PERFORMANCE LIST................................................................................................3
1-4 LAYOUT DIAGRAM & JUMPER SETTING ...............................................................4
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS.......................................................................6
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING ...............................................6
2-3 INSTALL CPU.............................................................................................................7
2-3-1 GLOSSARY.....................................................................................................7
2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU......................................................8
2-4 INSTALL MEMORY ....................................................................................................8
2-5 EXPANSION CARD....................................................................................................9
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION............................9
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD...................................................10
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD.....................10
2-5-4 AGP SLOT.......................................................................................................11
2-6 CONNECTORS, HEADERS .......................................................................................11
2-6-1 CONNECTORS................................................................................................11
2-6-2 HEADERS........................................................................................................14
2-7 STARTING UP YOUR COMPUTER...........................................................................17
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP.....................................................................................................18
3-2 GETTING HELP..........................................................................................................18
3-3 THE MAIN MENU........................................................................................................19
3-4 STANDARD CMOS FEATURES................................................................................20
3-5 ADVANCED BIOS FEATURES..................................................................................21
3-6 ADVANCED CHIPSET FEATURES...........................................................................23
3-6-1 DRAM TIMING SETTINGS .............................................................................24
3-7 INTEGRATED PERIPHERALS...................................................................................25
3-7-1 ONBOARD IDE FUNCTION............................................................................25
3-7-2 ONBOARD DEVICE FUNCTION....................................................................26
3-7-3 ONBOARD SUPER IO FUNCTION ................................................................27
3-8 POWER MANAGEMENT SETUP...............................................................................28
3-8-1 PM TIMER RELOAD EVENTS.......................................................................29
3-9 PNP/PCI CONFIGURATION SETUP..........................................................................30
3-9-1 IRQ RESOURCES..........................................................................................31
3-10 PC HEALTH STATUS ...............................................................................................31
3-11 MISCELLANEOUS CONTROL .................................................................................32
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS...........................................................33
3-13 SET SUPERVISOR/USER PASSWORD ..................................................................33
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 98SE/ME/NT4.0/2000/XP................................34
4-1 INF INSTALL INTEL 865 CHIPSET SYSTEM DRIVER ............................35
4-2 VGA INSTALL INTEL 865G VGA DRIVER .................................................35
4-3 SOUND INSTALL ALC AC97 CODEC AUDIO DRIVER..................................36
4-4 LAN INSTALL VIA 6105 LAN CONTROLLER DRIVER.............................37
4-5 USB2.0 INSTALL INTEL USB2.0 DRIVER ......................................................38
4-6 PC-HEALTH ..............................................................................................................IN
STALL SMART GUARDIAN SOFTWARE FOR HARDWARE
MONITORING DEVICE .......................................................................38
4-6-1 HOW TO UTILIZE PC-HEALTH.....................................................................39
4-7 MBIOS&DX8 INSTALL BIOS LIVE UPDATE UTILITY AND DIRECTX8.1 .......40
4-8 PC-CILLIN INSTALL PC-CILLIN2002 ANTI-VIRUS PROGRAM .........................41
4-9 HOW TO UPDATE BIOS ............................................................................................43
TABLE OF CONTENT

ii
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED,
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT
WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 865GDMC/865GDMCP/865PEDMC/
865PEDMCP MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT
WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS
IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTIALORCONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF
BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Release November 2003
Item Checklist
5865GDMC/865GDMCP/865PEDMC/865PEDMCP Motherboard
5Cable for IDE/Floppy
5CD for motherboard utilities
□ Cable for USB Port 3/4 (Option)
5865GDMC/865GDMCP/865PEDMC/865PEDMCP User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and concentrated
airflow from attached fans. In addition, interface materials allow effective transfers of heat from the
processor to the heatsink. For optimum heat transfer, Intel recommends the use of thermal grease and
mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below for collection of
heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are
recommended for maintaining the specified Maximum T case requirement. In addition, this collection
is not intended to be a comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index

1
Chapter 1
Introduction of 865GDMC/865GDMCP/
865PEDMC/865PEDMCP Motherboard
1-1 Feature of motherboard
The 865GDMC/ 865GDMCP/ 865PEDMC /865PEDMCP motherboard is design for use Intel
Pentium 4 Processor in 478 Pin Package/Northwood/Hyper Threading Processor with the
Intel 865G/865PE Chipset delivers a high performance and professional desktop platform
solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB.
These motherboards use the newest Intel 865G/865PE Chipset Supports 800/533/400MHz
System Bus in data transfer rate, the motherboards provided 200/166/133MHz SDRAM clock
frequency support DDR400/DDR333/DDR266 SDRAM. These motherboards also provided
Dual Channel function to increase memory performance. The motherboard embedded ICH4
chipset offers two parallel ULTRA ATA 100 interface to provide speedier HDD throughout
that boosts overall system performance.
865GDMC/865GDMCP with integrated 2D/3D Graphics Accelerator which supports 256 bit
graphics core, and supports hardware motion compensation assist for software MPEG/DVD
decode, makes this board lower cost alternative to a video card. For those wanting even
greater graphic performance, an AGP 4X slot is included on the board (For 1.5V AGP card
only. No for 3.3V or Universal AGP card). This AGP slot will support either a 4X/8X VGA
card.
The 865GDMCP/ 865PEDMCP motherboard including Fast Ethernet PCI controller chip
support 10Mb/s, 100Mb/s Base transfer rate.
These motherboards also has an integrated 6-channel AC97’ CODEC chip on board support
6-channel 3D surround positioning Audio which is fully compatible with Sound Blaster Pro®
that gives you the best sound quality and compatibility.
With USB control as well as capability of expanding to 6 USB2.0 function ports, these
motherboards meet future USB demand also these motherboard have built-in hardware
monitor function. This will monitor and protect your computer. These motherboards special
design in hardware to protect BIOS from virus crash BIOS data.
These motherboards provide special function in BIOS Setup to setting CPU Host clock step
by step increasing let users to approach over clocking.
These motherboards provided high performance & meet future specification demand. It is
really wise choice for your computer.

2
1-2 Specification
Spec Description
Design ∗Micro ATX form factor 4 layers PCB size: 24.4x22.0cm
Chipset ∗Intel 865G Graphics Memory Controller Hub (GMCH) Chipset
for 865GDMC/865GDMCP
∗Intel 865PE Memory Controller Hub (MCH) Chipset for
865PEDMC/865PEDMCP
∗Intel 82801DB I/O Controller Hub (ICH4) Chipset
CPU Socket
(mPGA478B Socket) ∗Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package processor
∗Support CPU Frequency 400MHz/533MHz/800MHz
∗Support 1.6G∼3.06G 478 Pin Pentium 4 processor
∗Reserves support for future Intel Pentium 4 processors
Memory Socket ∗184-pin DDR SDRAM module socket x2
∗Support Dual channel DDR266/DDR333/DDR400 DDR
SDRAM
∗Expandable to 2.0GB
Expansion Slot &
Headers ∗AGP slot x1 for AGP 0.8V/1.5V standard only, support AGP
2.0/3.0 & 4X/8X mode
∗32-bit PCI slot x 3
Integrate VGA
( for 865GDMC/
865GDMCP )
∗Integrated High Performance & High Quality 3D Accelerator
∗Support Ultra-AGPII with 2GB/s bandwidth
∗Built-in programmable 24-bit true-color RAMDAC up to
333MHz pixel clock.
Integrate IDE ∗Two IDE controllers support PCI Bus Mastering, ATA
PIO/DMA and the ULTRA DMA 33/66/100 functions that
deliver the data transfer rate up to 100 MB/s
LAN On Board
( for 865GDMCP/
865PEDMCP )
∗VIA VT6105 LOM PCI LAN controller chip
∗Supports 10/100 Mb/sec data transfer rate
Audio ∗Realtek ALC 6-channel AC97’ Codec integrated
∗Support 6-channel 3D surround & Positioning Audio
∗Audio driver and utility included
BIOS ∗Award 4Mb Flash ROM
Multi I/O ∗PS/2 keyboard and PS/2 mouse connectors
∗Floppy disk drive connector x1
∗Parallel port x1, Serial port x2
∗USB 2.0 connector x4, headers x2 (connecting cable option)
∗Audio connector Line-in, Line-out, MIC & Game Port

3
1-3 Performance List
The following performance data list is the testing result of some popular benchmark testing
programs. These data are just referred by users, and there is no responsibility for different
testing data values gotten by users (the different Hardware & Software configuration will
result in different benchmark testing results.)
Performance Test Report
CPU: Intel Pentium 4 2.53GHz (533MHz FSB)/3GHZ (800MHz FSB) mPGAB package
DRAM: 512MB DDR400 SDRAM x2 (KINGSTON D328DW)
On Board VGA: 1024x768x32bit Color
Hard Disk Driver: IBM IC35L040AVVN07-0 (ATA-100 7200RPM)
BIOS: Award Optimal default
OS: Win XP Prefessional (Service Pack 1)
2.53GHz
133/133 3GHz 200/200 3GHz 200/200 Dual Channel
3GHz 200/200
Dual Channel
Hyper-Threading
3D Mark 2001SE 2192 2506 2967 2929
3D Mark 2003 59 70 94 92
3D Winbench 2000 (32/32BIT) 73.2 78.3 83.3 83.1
PC Mark 2002
CPU/Memory/HDD 6146/5410/879 7336/6480/879 7364/7620/879 7380/7632/877
Content Creation Winstone 2002 41 48.9 51.7 46.4
Content Creation Winstone 2003 41.9 49.6 51.7 50.1
Business Winstone 2002 29.4 33.3 33.7 33.1
Winbench 99 V1.2:
Business Disk Winmark99 8600 8840 9190 9180
Hi-end Disk Winmark99 32200 31700 31800 32900
Business Graphic Winmark 164 205 226 277
Hi-end Graphic Winmark 591 852 874 898
SYS Mark 2001/2002 : SISMark 2001/2002 Rating (Internet Content Creation / Office Productivity)
SISMark 2001 236 (263/212) 278 (314/247) 286 (325/251) 271 (317/231)
SISMark 2002 in Windows XP 245 (346/173) 283 (411/195) 300 (429/210) 316 (436/229)
SISOFT Sandra 2003 :
Dhrystone ALU MIPS 6778 7712 7743 9183
Whetstone FPU iSSE2 MFLOPS 1407/3114 1711/3944 1708/3942 2601/5416
RAM Int Buffered iSSE2 MB/S 2204 2688 4226 4266
RAM Float Buffered iSSE2MB/S 2204 2689 4227 4263
Integer SSE2 IT/S 10033 11923 11925 11749
Floating-Point SSE2 IT/S 12768 15177 15178 21590
QUAKE3 DEMO1 FPS 110.9 125.6 134.1 134.5
DEMO2 FPS 110.5 127.3 136.3 135.9
Return to Castle Wolfenstein FPS 74.4 84.5 88.6 88.9
WCPUID System / CPU Clock 132.98/2526.62 199.66/2995.70 199.71/2995.70 199.71/2995.70

4
1-4 Layout Diagram & Jumper Setting
LINE-OUT
LINE-IN
COM1 VGA/COM2
(Option) USB1
MIC
PS/2 Mouse
PS/2 Keyboard
PRINT LAN
USB
VGA (for 865GDMC/865GDMCP)
COM2 (for 865PEDMC/865PEDMCP)
Front Panel Audio
CD Audio
ATX 12V Power Connector
ITE 8712 I/O Chip
PCI Slot
AGP 4X/8X 1.5V Slot
Floppy Connector
Intel 865G/865PE Chip
Front Panel Connecto
r
ATA 100 IDE Connector
Clear CMOS (JP3)
ATX Power Connector
CPU FAN
4MBit FWH BIOS
CPU Socket
DDR DIMMx2
SYSFAN1
Intel 82801DB Chip
Speak Connector
GAME Port Connector
6-CH AC’97 Audio Codec
PC99 Back Panel
K/B Power ON Jumper
(JP1)
USB Port/
LAN Connector
PS2 KB/Mouse Port
USB Port (USB1)
Audio Connector (CN1)
IR Connector
Wake On LAN
USB Port (USB2)
SYSFAN2
VIA VT6105 LAN Controller

5
Jumpers
Jumper Name Description Page
JP3 CMOS RAM Clear 3-pin Block P.6
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.7
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block P.11
ATX12V1 ATX 12V Power Connector 4-pin Block P.12
USB1, UL_B USB Port Connector 4-pin Connector P.12
LAN
(for 865GDMCP/865PEDMCP) LAN Connectors RJ-45 Connector P.12
KB
(PS2 KB/MOUSE) PS/2 Mouse & PS/2 Keyboard Connector 6-pin Female P.12
PARALLEL Parallel Port Connector 25-pin Female P.12
CN1 Audio Line In/Out MIC Connector 3 phone jack Connector P.12
VGA
(for 865GDMC/865GDMCP) VGA Display Connector 15-pin Female Connector P.12
COM1 Serial Port COM1 Connector 9-pin Connector P.12
COM2
(for 865PEDMC/865PEDMCP) Serial Port COM2 Connector 9-pin Connector P.12
FDD Floppy Driver Connector 34-pin Block P.13
IDE1/IDE2 Primary/Secondary 40-pin Block P.13
Only for 865GDMC/865GDMCP
Headers
Header Name Description Page
AUDIO Line-Out, MIC Headers 9-pin Block P.14
USB2 USB Port Headers 9-pin Block P.14
SPEAK Speaker connector 4-pin Block P.14
JW_FP
(Power LED/Reset/
IDE LED/ Power Button)
Front Panel Header
(including Power LED/ IDE activity LED/
Reset switch / Power On Button lead)
9-pin Block P.14
WOL Wake On-LAN Headers 3-pin Block P.15
SYSFAN1, SYSFAN2,
CPUFAN FAN Speed Headers 3-pin Block P.15
IR IR infrared module Headers 5-pin Block P.16
CDIN CD Audio-In Headers 4-pin Block P.16
GAME Game Port Header 15-pin Block P.16
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 478 CPU Socket 478-pin mPGAB CPU Socket P.8
DIMM1 /DIMM2 DDR Module Socket 184-pin DDR SDRAM Module
Expansion Socket P.8
PCI1 ∼PCI3 PCI Slot 32-bit PCI Local Bus Expansion slots P.9
AGP AGP 4X/8X Mode Slot AGP Expansion Slot P.11

6
Chapter 2
Hardware installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JP3
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JP3 to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JP3 and short pins 2-3 for a few seconds
4. Return JP3 to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
CMOS RAM Clear Setting
JP3 13
2-3 closed Clear CMOS
JP3 1 3
1-2 closed Normal (Default)

7
(2) Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password/USB device to power
on system.
JP1 2-3 closed K/B Power ON Enabled
JP1 1-2 closed K/B Power ON Disabled (Default)
JP1
1
3
JP1
1
3
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces between
the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for
sound cards and modems; runs at approx. 8MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"
Front Side Bus Frequency - the working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache - the flash memory inside the CPU, normally Athlon CPU has 256K or above,
while Duron will have 64K.

8
2-3-2 About Intel Pentium 4 478-pin CPU
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.
WARNING! Be sure that there is sufficient air circulation across the processor’s heatsink and
CPU cooling FAN is working correctly, otherwise it may cause the processor and
motherboard overheat and damage, you may install an auxiliary cooling FAN, if
necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the level sideways away from the socket then upward to a 90-degree
angle. Insert the CPU with the correct orientation as shown below. The notched corner
should point toward the end of the level. Because the CPU has a corner pin for two of the
four corners, the CPU will only fit in the orientation as shown.
CPU ZIF mPGAB Socket
Colden Arrow
mPGA478B
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press
the level to Locate position slightly without any extra force.
2-4 Install Memory
This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 64MB to maximum
memory size of 2.0GB DDR SDRAM.
Valid Memory Configurations
Bank 184-Pin DIMM PCS Total Memory
Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400
DDR SDRAM Module X1 64MB∼1.0GB
Bank 2, 3 (DIMM2) DDRDDR266/DDR333/DDR400
DDR SDRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 2.0GB) 4 64MB∼2.0GB

9
For Dual channel Limited!
1. Dual channel function only supports when 2 DIMM Modules plug both DIMM1 & DIMM2
2. DIMM1 & DIMM2 must be the same type, same size, same frequency for dual channel
function.
Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to
figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks like.
DIMM2 (BANK2+ BANK3) DIMM1 (BANK0+ BANK1)
NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be
locked into the DIMM module very firmly and fit into its indention on both sides.
WARNING! For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400-compliant DDR
Modules. When this motherboard operate at 200Mhz, most system will not even
boot if non-compliant modules are used because of the strict timing issues, if your
SDR Modules are not DDR266-compliant, set the DDR SDRAM clock to 133MHz
to ensure system stability.
2-5 Expansion Cards
WARNING! Turn off your power when adding or removing expansion cards or other system
components. Failure to do so may cause severe damage to both your motherboard
and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Figure 2-4

10
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1 √
Slot 2 √
Slot 3 √
Onboard VGA √
Onboard LAN √
Onboard USB 1 √
Onboard USB 2 √
Onboard USB 3 √
Sound √
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared
IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between
the two PCI groups that will make the system unstable or cards inoperable.
2-5-4 AGP Slot
This motherboard provides an AGP Slot, only support the 1.5V 4X/0.8V 8X AGP VGA card.
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to
Intel® 865 chipset can not support AGP 2X (3.3V).

11
IMPORTANT! Before you plug-in AGP card, please make sure the following notice is fully
understood and practiced. If your AGP card has “AGP 4X notch (show
below) please make sure your AGP card is AGP 4X/8X (1.5V/0.8V) not AGP
2X (3.3V)
AGP SLOT
Example 1: SiS 305 & ATi Rage 128 Pro AGP card those golden finger is compatible with
2X/4X mode AGP slot, but only can support 2X (3.3V) only. If you install these
cards in Intel® 865 based motherboard it will burn and damage the motherboard.
Example 2: We also find Diamond Vipper V770 golden finger is design for 2X/4X mode AGP
Slot. It can be adjusted the jumper for AGP 2X (3.3V) or AGP 4X (1.5V). But the
factory default setting is 2X (3.3V). If you install this AGP card in motherboard
without change the jumper setting to 4X (1.5V), it will burn the motherboard.
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with
ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect
from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the
power switch on the back of the ATX power supply turned on, the full power will not come into
the system board until the front panel switch is momentarily pressed. Press this switch again
will turn off the power to the system board.
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V
Pin 1
(2) ATX 12V Power Connector (4-pin block) : ATX12V1
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX
Power Supply which fully support Pentium 4 processor must including this connector for
support extra 12V voltage to maintain system power consumption. Without this connector might
cause system unstable because the power supply can not provide sufficient current for system.
2x notch 4x notch

12
Pin 1
(3) USB Port connector: USB1, UL_B (USB)
The connectors are 4-pin connector that connect USB devices to the system board.
(4) LAN Port connector: LAN (for 865GDMCP/865PEDMCP)
This connector is standard RJ45 connector for Network connector.
(5) PS/2 Mouse & PS/2 Keyboard Connector: KB (PS2 KB/MOUSE)
The connectors for PS/2 keyboard and PS/2 Mouse.
(6) Parallel Port Connector (25-pin female): PARALLEL
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 “INTEGRATED
PERIPHERALS SETUP” section for more detail information.
(7) Audio Line-In, Lin-Out, MIC Connector : CN1
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC
Line-out : Audio output to speaker
Line-in : Audio input to sound chip
MIC : Microphone Connector
(8) VGA Connector (15-pin D-Sub) Connector: VGA (for 865GDMC/865GDMCP only)
VGA is the 15-pin D-Subminiature female connector for display monitor.
(9) Serial Port COM1/COM2: COM1/COM2 (COM2 only for 865PEDMC/865PEDMCP)
COM1/COM2A is the 9-pin D-Subminiature mail connector. The On-board serial port can be
disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS
SETUP” section for more detail information.
(10) Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. After connecting the single
plug end to motherboard, connect the two plugs at other end to the floppy drives.
LINE-OUT
LINE-IN
MIC
COM1 VGA/COM2
(Option)
PS/2 Keyboard USB
USB1PS/2 Mouse PRINT LAN

13
Floppy Drive Connector
Pin 1
FDD
(11) Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If
you install two hard disks, you must configure the second drive to Slave mode by setting its
jumpers accordingly. Please refer to the documentation of your hard disk for the jumper
settings.
(12) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the same
procedure described for the primary IDE connector. You may also configure two hard
disks to be both Masters using one ribbon cable on the primary IDE connector and another
ribbon cable on the secondary IDE connector.
Pin 1
IDE1
Pin 1
IDE2
•Two hard disks can be connected to each connector. The first HDD is referred to as the
“Master” and the second HDD is referred to as the “Slave”.
•For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM
drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.

14
2-6-2 Headers
(1) Line-Out, MIC Header (9-pin): AUDIO
This header connect to Front Panel Line-out, MIC connector with cable.
Line-Out, MIC Headers
A
UDIO
Pin 1
AUD-MIC
AUD-FPOUT-L
AUD-MIC-BIAS
AUD-FPOUT-R
HP-ON
AUD-GND
AUD-RET-L
AUD-RET-R
AUD-VCC
2
910
(2) USB Port Headers (9-pin) : USB2
The header is used for connecting the additional USB port plug. By attaching an option
USB cable, your can be provided with two additional USB plugs affixed to the back
panel.
USB Port Headers
Pin 1
USB2
VCC
-DAT
A
GND
+ DATA
VCC
OC
-DAT
A
GND
+ DATA
(3) IDE Activity LED: IDE LED
This connector connects to the hard disk activity indicator light on the case.
(4) Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the lift of the system’s power supply. See the figure
below.
(5) Speaker connector: SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(6) Power LED: PWR-LED
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.
(7) Power switch: PWR BTN
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.

15
System Case Connections
JW_FPSPEAK
SPKR
GND
NC
VCC5
Pin 1
Pin 1
HDLED
RESET
VCC5
GND
VCC5 ACPILED
PWRBTN
PWRBTN
ACPILED
HDDLED
RSTSW
NC GND
(8) Wake On-LAN Headers (3-pin) : WOL
This connector connects to a LAN card with a WAKE ON-LAN output. This
connector power up the system when a wake up signal is received through the LAN
card.
NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
Wake-On-LAN Headers
WOL
13
5VSB GND WOL
(9) FAN Speed Headers (3-pin) : SYSFAN1, SYSFAN2, CPUFAN
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan
manufacturer, the wire and plug may be different. The red wire should be positive, while
the black should be ground. Connect the fan’s plug to the board taking into consideration
the polarity of connector.
FAN Headers
CPUFAN
13
SYSFAN2
13
SYSFAN1
13

16
(10) IR infrared module Headers (5-pin) : IR
This connector supports the optional wireless transmitting and receiving infrared module. You
must configure the setting through the BIOS setup to use the IR function.
IR infrared module Headers
IR
Pin 1
GND
IRRX
NC
VCC5
IRTX
2
5
6
(11) CD Audio-In Headers (4-pin) : CDIN
CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio
output connector.
CD Audio-In Headers
CDIN 4 1
(12) Game Port Header: GAME
Pin 1
GAME Port Headers

17
2-7 Starting Up Your Computer
1. After all connection are made, close your computer case cover.
2. Be sure all the switch are off, and check that the power supply input voltage is set to
proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.
3. Connect the power supply cord into the power supply located on the back of your system
case according to your system user’s manual.
4. Turn on your peripheral as following order:
a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply
and press the ATX power switch on the front side of the case.
5. The power LED on the front panel of the system case will light. The LED on the monitor
may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.
If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.
Beep Meaning
One short beep when displaying logo No error during POST
Long beeps in an endless loop No DRAM install or detected
One long beep followed by three short
beeps Video card not found or video card memory bad
High frequency beeps when system is
working CPU overheated
System running at a lower frequency
6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in
BIOS SETUP.
7. Power off your computer: You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click “Start” button, click “Shut down” and then click “Shut down the computer?”
The power supply should turn off after windows shut down.