Jl audio Stealthbox sb-can-mvx3pass/10tw3 User manual

INSTALLATION GUIDE

for the

SB-CAN-MVX3PASS/10TW3

SKU# 94663

2017 & Up Can-Am Maverick X3 2-seat (Passenger)

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the Stealthbox®be properly mounted to the vehicle

according to these instructions. Failure to mount the enclosure

properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

D IFF ICU LT Y:

ESTIMATED TIME:

2 HOURS

Enclosure Type: Sealed

Driver Type: 10TW3-D4

Nominal Impedance: 2 ohms

Continuous Power Handling: 400 watts (RMS method)

Continued on Next Page

OUT

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2018

BOM ID Qty SKU Description

1 6 151709 1/4 - 20 x 1-1/2” Socket Cap Screw

2 6 150066 1/4” Split Lock Washer

3 6 153734 1/4” Flat Washer

4 2 153764 Stainless Steel Cushion Clamp

5 1 152431 Template

- 1 150249 Foam Tape (not shown)

Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the

amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2018

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

Page 4 • JL Audio, Inc., 2018 Continued on Next Page

STEP 8

Remove the Template from the vehicle.

Using a 1/8” drill bit, drill a pilot hole through

each of the marks made in the previous step.

STEP 7

Using a small pick tool, mark each of the hole

locations through the Template onto the

plastic floor panel.

STEP 6

Position the Template on the vehicle floor. Push

the Template forward and to the outside, as

shown, until flush with the frame rails.

STEP 5

Unplug the seat belt wiring harness.

Carefully remove the passenger seat from the

vehicle.

STEP 4

Remove the seat belt bolt.

STEP 3

Slide the passenger seat forward.

Remove the two rear seat bolts from the seat

bracket.

STEP 2

Remove the two front seat bolts from the

passenger seat bracket.

STEP 1

Empty the front of the vehicle.

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

Page 5 • JL Audio, Inc., 2018 Continued on Next Page

STEP 16

Slide a 1/4” Split Lock Washer and a 1/4” Flat

Washer over each of four 1/4 - 20 x 1-1/2”

Socket Cap Screws.

From under the vehicle, pass each assembly

through a drilled hole in the floor panel, into a

threaded insert in the bottom of the enclosure,

and fully tighten.

STEP 15

Tighten the eight subwoofer mounting screws.

STEP 14

Push the enclosure forward, allowing it to drop

into position. Place the subwoofer back into

the enclosure.

STEP 13

Partially lift the subwoofer out of the enclosure,

as shown. This allows for clearance to position

the enclosure in the next step.

STEP 12

Carefully set the enclosure into the vehicle, as

shown.

STE P 11

Completely loosen the eight subwoofer

mounting screws, but do not remove them.

STEP 10

Place the Stealthbox® face down on a flat

surface. Attach Foam Tape to the bottom of the

enclosure, as shown.

STEP 9

Using a 5/16” drill bit, enlarge each of the pilot

holes drilled in the previous step.

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

Page 6 • JL Audio, Inc., 2018

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

MID/HIGH FREQUENCY DRIVER FITMENT

VeX™ Enclosed Speaker Systems are ideal for powersports and o-road vehicle applications. Each

weatherproof pod can be mounted to a roll cage precisely aimed for optimum sound. Mounting

xtures are available to t a variety of roll cage diameters.

STEP 20

Pictured is the Stealthbox® completely secured.

Connect speaker cable to the barrier strip on

the back of the enclosure, and route the cable

as necessary.

STEP 19

Repeat the process for the outside front frame

rail position.

Fully tighten both 1/4 - 20 x 1-1/2” Socket Cap

Screws.

STEP 18

Wrap a Stainless Steel Cushion Clamp over the

inside front frame rail, aligning its holes with

the threaded insert in the top of the enclosure.

Slide a 1/4” Split Lock Washer and a 1/4” Flat

Washer over a 1/4 - 20 x 1-1/2” Socket Cap

Screw, pass the assembly through the holes in

the Stainless Steel Cushion Clamp, and into the

threaded insert.

STEP 21

Carefully reinstall the passenger seat.

Connect the seat belt harness, reinstall the seat

belt bolt, the two rear seat bolts, and the two

front seat bolts.

Note: For optimum performance, we

recommend applying the included Foam Strips

(or sound damping material) to surrounding

plastic panels to reduce unwanted vibrations.

SB-CAN-MVX3PASS/10TW3 INSTR_SKU# 011509

All specifications are subject to change without notice. “JL Audio®” and “How we play®” are registered trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo are trademarks

of JL Audio, Inc.