Jl audio Stealthbox sb-y-yxz1/10tw3 User manual

INSTALLATION GUIDE

for the

SB-Y-YXZ1/10TW3

SKU# 94642

2016 & Up Yamaha YXZ1000R

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the Stealthbox®be properly mounted to the vehicle

according to these instructions. Failure to mount the enclosure

properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

D IFF I CU LT Y:

ESTIMATED TIME:

23 HOURS

Enclosure Type: Sealed

Driver Type: 10TW3-D4

Nominal Impedance: 2 ohms

Continuous Power Handling: 400 watts (RMS method)

Continued on Next Page

OUT

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2017

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

BOM ID Qty SKU Description

1 8 153729 1/4 - 20 x 1” Serrated Flange Bolt

2 2 153876 Bracket

3 4 153739 1/4” Serrated Spring Lock Washer

4 4 153740 1/4 - 20 Hex Nut

5 1 152330 Template Front

6 1 152331 Template Rear

- 1 150249 Foam Tape (not shown)

Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the

amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2017

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 4 • JL Audio, Inc., 2017 Continued on Next Page

STEP 8

Remove the two clips from the front of the

lower side panel, and remove the panel from

the vehicle.

STEP 7

Remove the bolt from the top of the lower side

panel.

STEP 6

Remove the body panel from the vehicle.

STEP 5

Remove the clip from the top of the body

panel.

STEP 4

Remove the two screws from the rear of the

body panel.

STEP 3

Remove the screw from the top of the body

panel.

STEP 2

Remove the two bolts from the front of the

driver’s side body panel

STEP 1

Empty the front of the vehicle.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 5 • JL Audio, Inc., 2017 Continued on Next Page

STEP 16

Remove the upper console panel from the

vehicle.

STEP 15

Lift up on the back of the upper console panel

to unclip it.

STEP 14

Remove the two clips from the driver’s side of

the lower console panel.

STEP 13

Remove the four clips from the top of the

upper seat bracket trim panel.

STEP 12

Remove the upper seat bracket from the

vehicle.

STEP 11

Remove the four upper seat bracket bolts.

STEP 10

Lift up on the driver’s seat, and remove the seat

from the vehicle.

STEP 9

Remove the seat belt bolt.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 6 • JL Audio, Inc., 2017 Continued on Next Page

STEP 24

Remove the bolt from the front of the lower

rear panel.

STEP 23

Remove the clips from the front of the upper

and lower rear panels.

STEP 22

Remove the lower console panel from the

vehicle.

STEP 21

Remove the four clips from the top of the lower

console panel.

STEP 20

Remove the dash trim panel from the vehicle.

STEP 19

Remove the two bolts from the top of the dash

trim panel.

STEP 18

Remove the two screws from the bonnet trim

panel, and remove the panel from the vehicle.

STEP 17

Remove the clip from the dash trim panel over

the center console.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 6 • JL Audio, Inc., 2017 Continued on Next Page

STEP 32

Remove the lower rear panel from the vehicle.

STEP 31

Remove the lower seat bracket from the

vehicle.

STEP 30

Remove the four lower seat bracket bolts.

STEP 29

From below the vehicle, remove the two bolts

from under the skid panel.

STEP 28

Remove the two bolts from the side of the skid

panel.

STEP 27

Remove the bolt from the back of the upper

rear panel.

STEP 26

Remove the bolt from the back of the lower

rear panel.

STEP 25

Remove the bolts from the front of the

footwell.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 6 • JL Audio, Inc., 2017 Continued on Next Page

STEP 40

From below the frame, raise the Stealthbox®

into position.

STEP 39

Turn the enclosure over, and apply Foam Tape

to the recessed area, as shown.

STEP 38

Place the enclosure face up on a flat surface.

Apply Foam Tape the recessed area, as shown.

STEP 37

Secure a Bracket to the factory holes in the

front frame rail using a pair of 1/4 - 20 x 1”

Serrated Flange Head Bolts above the frame

and a pair 1/4” Serrated Spring Lock Washers

and 1/4 - 20 Hex Nuts below the frame, as

shown.

Do not fully tighten at this time.

STEP 36

Secure a Bracket to the factory holes in the rear

frame rail using a pair of 1/4 - 20 x 1” Serrated

Flange Head Bolts above the frame and a pair

1/4” Serrated Spring Lock Washers and 1/4 - 20

Hex Nuts below the frame, as shown.

Do not fully tighten at this time.

STEP 35

Pictured are the Brackets. The sides with the

longer flange get attached to the vehicle’s

frame rails in the following steps.

STEP 34

Lower the skid panel down, as shown. It is not

necessary to completely remove the panel

from the vehicle.

STEP 33

Remove the four clips from the top of the lower

seat bracket trim panel, and remove the panel

from the vehicle.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 6 • JL Audio, Inc., 2017 Continued on Next Page

STEP 48

Connect speaker cable to the barrier strip on

the side of the enclosure, and route the cable

as necessary.

Reinstall the lower seat bracket trim panel, as

shown.

STEP 47

Pictured is the lower seat bracket trim panel

after cutting.

STEP 46

Carefully cut along the marks to remove the

two sections of the lower seat bracket trim

panel, as shown.

STEP 45

Remove the clips, and remove Template.

STEP 44

Mark the left and middle sections in the

Template onto the lower seat bracket trim

panel.

STEP 43

Tape the two halves of the Template together,

position the template over the lower seat

bracket trim panel, and secure using a pair of

factory clips, as shown.

STEP 42

Place the lower seat bracket trim panel on a flat

surface, as shown.

STEP 41

Align the threaded inserts in the side of the

enclosure with the slots in the two Brackets.

Secure the enclosure to each bracket using a

pair of 1/4 - 20 x 1” Serrated Flange Head Bolts,

and fully tighten.

Fully tighten the two 1/4 - 20 x 1” Serrated

Flange Head Bolts holding the Brackets to the

frame rails.

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

Page 7 • JL Audio, Inc., 2017

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

SB-Y-YXZ1/10TW3 INSTR_SKU# 011479

STEP 51

Reinstall the seat belt bolt, the lower side

panel, and the body panel.

STEP 50

Reinstall the upper seat bracket trim panel,

lower console panel, upper console panel, dash

trim panel, and bonnet trim panel.

STEP 49

Reinstall the skid panel, lower rear panel, and

the lower seat bracket.

MID/HIGH FREQUENCY DRIVER FITMENT

SB-Y-YXZSPKR/MX650 speaker pods are also available for your vehicle. Each weatherproof pod is

designed for a perfect t and houses a premium JL Audio coaxial system.

SB-Y-YXZ1-SPKR/MX650

SKU# 94643

(954) 443-1100

www.jlaudio.com

JLA-SKU# 011479 • ver. 07.25.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the