JL Audio Stealthbox SB-T-TACDC12/10TW3 User manual

INSTALLATION GUIDE
for the
SB-T-TACDC12/10TW3
SKU# 94557
2012 & Up Toyota Tacoma Double Cab
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your
own installation, please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
INSTALLATION
DIFFICULTY:
25
OUT
OF
ESTIMATED TIME:
2 HOURS
SPECIFICATIONS
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
INCLUDED HARDWARE
(2) Brackets
(4) 1/4 - 20 x 1” Hex Bolt
(4) 1/4” Lock Washer
(4) 1/4” Flat Washer
(2) 1/4 - 20 U-Nut

SB-T-TACDC12/10TW3 INSTR_SKU# 011350
POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio XD300/1v2. The diagram below shows the recommended crossover settings for the XD300/1v2. For a detailed description of the amplier settings,
consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other kits
are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplier. JL Audio
recommends using 12AWG speaker wire for subwoofers.
Continued on Next PagePage 2 • JL Audio, Inc., 2016

Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
Page 3 • JL Audio, Inc., 2016
STEP 4
On the backside of the rear panel, locate the two recessed
areas, then measure and mark 1” down the center from the
edge as shown. Drill a 1/8” pilot hole on the mark.
STEP 8
Slide a 1/4 - 20 U-Nut through each of the 3/4” holes and
align them with the 7/16” holes as shown.
STEP 3
Empty out the storage pocket. Remove the clips that hold in
the rear panel and remove the panel.
STEP 7
Drill 3/4” holes on the marks made in the previous step. Use
caution so as not to drill through the back of the cab.
STEP 2
Carefully unclip the seat bolt covers at the corners of the rear
seat backs. Unbolt and remove the seat backs.
STEP 6
Measure and mark 1” to the right of each pilot hole. Enlarge
the 1/8” pilot holes in both the metal and the plastic to 7/16”.
Use caution so as not to drill through the back of the cab.
STEP 1
Empty out the back seat of the vehicle and fold the seats
down.
STEP 5
Reinstall the panel. Drill through the pilot holes made in the
previous step to create pilot holes in the metal. Use caution
so as not to drill through the back of the cab. Remove the
panel again.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!

SB-T-TACDC12/10TW3 INSTR_SKU# 011350
Page 4 • JL Audio, Inc., 2016
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will t in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6x9”- Front Doors
Fits JL Audio Models: TR690-TXi, C2-690tx
Rear Speaker Size / Location: 6-1/2”- Rear Door
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650,
C3-650, C5-650x, C5-650 & ZR650-CSi
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011350 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
CONGRATULATIONS!
You have completed the installation for this model. Enjoy your new Stealthbox®!
STEP 12
Attach speaker cable to the Stealthbox® and place the
enclosure back into position. Secure the enclosure using a
pair of 1/4 - 20 x 1” Hex Bolts, 1/4” Lock Washers, and 1/4” Flat
Washers as illustrated.
ST EP 11
Pictured is a Bracket attached to the Stealthbox®.
STEP 10
Attach each Bracket to the threaded inserts in the top of the
enclosure using a 1/4 - 20 x 1” Hex Bolt, a 1/4” Lock Washer,
and a 1/4” Flat Washer as illustrated.
STEP 9
If an amplifier will be mounted into the recess in the front of
the Stealthbox®, set the enclosure into position and mark the
location of the wire channel. Remove the enclosure, and drill
a 1” hole in the panel. Reinstall the panel into the vehicle.
Note: This step is not necessary if the amplifier will be
mounted elsewhere.