JL Audio Stealthbox SB-GM-4GSUVCNSL/10TW1 User manual

INSTALLATION GUIDE
for the
SB-GM-4GSUVCNSL/10TW1
SKU# 94644
2015-Up Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL
Cadillac Escalade, & Escalade ESV
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
DIFFICULTY:
ESTIMATED TIME:
1 HOUR
Enclosure Type: Sealed
Driver Type: 10TW1-2
Nominal Impedance: 2 ohms
Continuous Power Handling: 300 watts (RMS method)
Continued on Next Page
15
OUT
OF
SB-GM-4GSUVCNSL/10TW1 INSTR_SKU# 011490

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2017
SB-GM-4GSUVCNSL/10TW1 INSTR_SKU# 011490
No additional hardware required.

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio XD300/1v2. The diagram below shows the recommended crossover settings for the XD300/1v2. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
Rem. |Oset | Signal
Input Voltage
Low | High
Turn-On Mode
Monoblock Subwoofer Amplifier
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2017
SB-GM-4GSUVCNSL/10TW1 INSTR_SKU# 011490

Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
Unclip the hood release, and remove the
bolster panel from the vehicle.
STEP 7
Remove the bolster panel from the dash.
STEP 6
Carefully unclip the bolster panel.
STEP 5
Remove the two T15 Torx screws from the
bottom of the bolster panel.
STEP 4
Remove the two T15 Torx screws from the side
of the bolster panel.
STEP 3
Remove the dash trim panel from the vehicle.
STEP 2
Carefully unclip the dash trim panel on the
driver’s side.
STEP 1
Empty the driver and passenger front seat area.
SB-GM-4GSUVCNSL/10TW1 INSTR_SKU# 011490

Page 5 • JL Audio, Inc., 2017 Continued on Next Page
STEP 16
Disconnect the wiring harnesses from the
lower console.
STEP 15
Disconnect the wiring harnesses from the
upper console trim panel, and remove the
panel from the vehicle.
STEP 14
Open the center console lid. Carefully unclip
the upper console trim panel.
STEP 13
Remove the 15mm bolt from the back of the
center console.
Repeat Steps 9-13 for the passenger side.
STEP 12
Slide the seat forward. Carefully unclip the bolt
cover panel.
STEP 11
Remove the 15mm bolt from the base of the
center console.
STEP 10
Remove the lower trim panel from vehicle.
STEP 9
Carefully unclip the lower trim panel from the
side of the center console.
SB-GM-4GSUVCNSL/10TW1 INSTR_SKU# 011490