JL Audio Stealthbox SB-GM-CAM12W6v2 User manual

INSTALLATION GUIDE
for the
SB-GM-CAM12W6v2
SKU#94472
2010+
Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Empty out the trunk of the car so that you have a Clean area
to work in, the area that the work will be performed in is
indicated by the arrow.
Continued on Next Page
S T E P 2
The only hole that we need to be concerned with is
indicated by the arrow. Insert a bolt from the backside of the
hole with a fender washer behind the hole then a fender
washer, split lock washer and nut as shown in the DETAIL
below.
D E T A I L
SB-GM-CAM12W6V2 INSTR_SKU# 011301
INSTALLATION
D I F F I C U LT Y :
15
OUT
OF
ESTIMATED TIME:
1 HOUR

SB-GM-CAM12W6V2 INSTR_SKU# 011301
CONGRATULATIONS!
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
D E T A I L
S T E P 4
Slide the bracket into place and start the Hex Head Bolt, Split
Lock Washer and Fender washer in as shown in the DETAIL
below which shows all of the hardware as it will finally be
assembled.
Install the Fender Washer, Split Lock Washer and Hex Nut
on the bolt originally installed in step 2, securing the
Stealthbox® in place.
S T E P 3
With the bolt installed as shown, tighten it. Slide the
Stealthbox® into place, familiarize yourself with the threaded
insert in the top of the Stealthbox®
Page 2 • JL Audio, Inc 2009
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011301 10.06.2009 • Printed in USA • ©2009 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 OtherU.S. & Foreignpatentspending.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
1) Custom Mount Bracket 5) 3/8” x 1-1/4” Fender Washer
3) 3/8” Split Lock Washer 2) 3/8-16 Hex Nut
1) 3/8-16 x 1” Hex Nut 1) 3/8-16 x 1-1/2” Hex Nut
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 12W6v2-D4
Nominal Impedance: Dual 4 ohm Voice Coil wired to 2 Ohms
Continuous Power Handling: 600 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality amplifiers such as the JL Audio HD750/1, 500/1v2 or G1700. The diagram below
shows the recommended crossover, infrasonic filter and equalizer settings for the HD750/1. If another amplifier is
being used, please reference this illustration and use similar settings on that amplifier.
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more
detailed information about installing and tuning your amplifier.
C O N N E C T I O N S
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XC-PCS4-1B for your Stealthbox® amplifier, other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5”- Front Doors
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi
Rear Speaker Size / Location: 6” x 9” - Rear Deck
Fits JL Audio Models: TR690-TXi, C2-690tx