JLL CT300 User manual

USER MANUAL
CT-300
93015

Important: Please locate your serial number and record in the box below for service support
purposes.
Serial number here:

Serial number

CT-300

CT-300

CT-300

Exploded drawing.
l-12
L-14

G-4
G-3
G-2
G-1
G-5 G-6 G-7
l-12L-14

Parts List
Number Description Q'ty Unit
A, A-1 Console & Screw 1 SET
B Front handlebar 1 PC
B-1 Foam grip 2 PCS
B-2 Hand pulse 2 PCS
B-3 End cap for front handlebar 2 PCS
B-4 Screw M4x20L for hand pulse 2 PCS
B-5 Semicircle washer 1.5T for hand pulse 2 PCS
B-6 Wire for hand pulse 1 PC
C Upper handlebar (Left) 1 PC
C-1 End cap for upper handlebar 2 PCS
C-2 Foam grip for upper handlebar 2 PCS
C-3 Upper handlebar (Right) 1 PC
D Handlebar post 1 PC
D-1 Cable (upper) for handlebar post 1 PC
D-2 Screw M5xP0.8x12L 2 PCS
D-3 Cover for console holder(Left) 1 PCS
D-4 Cover for console holder(Right) 1 PCS
D-5 Bushingφ38.1xφ17.12x15L 2 PCS
D-6 Axle for the handlebar post 1 PCS
E-L Lower handlebar(Left) 1 PC
E-R Lower handlebar(Right) 1 PC
E-1 Bushing φ38.1xφ17.12x15L 4 PCS
E-2 C type ringφ12 4 PCS
E-3 Flat washerφ12xφ19x1t 4 PCS
E-4 Bushingφ12xφ16 4 PCS
E-5 Sleeveφ16*φ20*26L 2 PCS
E-6 Wave washerφ12.5xφ18x0.3t 4 PCS
F Main frame 1 PC
F-2 Flat washerφ8*φ19*2T 4 PCS
F-3 Allen bolt M8*P1.25*16L(6m/m) 4 PCS
F-4 C type ringφ20 1 PCS
F-5 Wave washerφ20xφ30x0.3t 1 PCS
F-6 Flat washerφ20.3xφ30x1t 1 PCS
F-7 Bearing 2 PCS
F-8 Sensor box 1 PCS
F-9 Big pulley 1 PCS
F-10 Hex. Screw M8xP1.25x12Lx5t 3 PCS
F-11 Belt 1 PCS
F-12 Sleeveφ20.5xφ25x7.5mm 1 PCS
F-13 Shaft 1 PCS
F-14 Screw M4*12L 10 PCS
F-15 Inside cover for disc 2 PCS

F-16 Cross disc 2 PCS
F-17 Flat washerφ5xφ16x1t 4 PCS
F-18 Nut M10xP1.25x10T for Cross disc 2 PCS
F-19 Front cover (Right ) 1 PC
F-20 Chain cover (Right ) 1 PC
F-21 Screw M5x16L 6 PCS
F-22 Round disc 2 PCS
F-23 Chain cover (Left) 1 PC
F-24 Self tapping screw M4x50L 7 PCS
F-25 Front cover (Left) 1 PC
F-26 Cover for the handlebar post 1 PC
F-27 Screw M4x10L for sensor box 1 PC
F-28 DC wire 1 PC
F-29 Cap for Round disc 2 PCS
F-30 Adaptor 1 PC
G-1~G-8 Flywheel set 1 SET
H-1~H-12 Idler wheel set 1 SET
I ~I-9 Magnetic set 1 SET
J Rear stabilizer 1 PC
J-1 Block for the adjustable foot cap 4 PCS
J-2 Foot cap 4 PCS
J-3 End cap for rear stabilizer 2 PCS
J-4 Front stabilizer 1 PC
J-5 Nylon nut M8 2 PCS
J-6 Flat washerφ8*φ19*2T 2 PCS
J-7 Transportation wheel 2 PCS
J-8 Screw M8xP1.25x40L 2 PCS
K-L Left pedal arm 1 PCS
K-1 Screw M5xP0.8x12L 4 PCS
K-2 Front cover (Left) for pedal arm 2 PCS
K-3 Bushingφ26.7xφ17.12x15L 4 PCS
K-4 Front cover (Right) for pedal arm 2 PCS
K-5 Left pedal 1 PCS
K-6 Right pedal 1 PCS
K-R Right pedal arm 1 PCS
L-1~L-24 Bolts & Nuts pack 1 SET
M, F-1 Gear box 1 SET

Assembly Stage #1
1. Attach the front stabilizer (J-4) to the main frame (F) using two flat washer (L-23) and allen bolt
(L-11).
2. Attach the rear stabilizer (J) to the main frame (F) using two flat washer (L-23) and allen bolt
(L-11) .
3. Please remove the handlebar post cover (F-26) from the main frame (F).
After assembly, the Trainer can be adjusted to slightly uneven ground by adjusting the height of the foot
caps at the front and back. The pre-assembled transportation wheels in the front allow easy moving of
the Elliptical and therefore during assembly, need to be pointing down at the front (45°).
Assembly Stage #2
1. Assemble the R/L pedal arm (K-L, K-R) to the cross disc (F-16) by wave washer (L-9) ,flat washer
(L-7) , gasket (L-6), and allen bolt (L-5).
L-11: Allen Bolt
M8*P1.25*16L (4)
L-23: Flat washer
Ø8*Ø19*2T (8)
Allen Key(1)
L-6:(2 )
L-5: M8*P1.0*30L(2)
Allen Key(2)
L-9: Curved Washer
Ø17.5*25*0.3t (2)
L-7: Teflonwasher
Ø8* Ø25*2t (2)