JNS Aquaria FR-S User manual

Internal GFO Carbon and Biopellet Filter
Media Reactor
1Please open the package carefully, and check if
there’s any damaged or missing part.
2While we take great care to keep any contaminants
away from our products during assembly, please
take a moment to clean with warm water ONLY.
Never clean Acrylic with alcohol-based products. Use
caution when handling acrylic scratches easily.
3Some media (such as phosphate control products) is
not designed to be aggressively fluidized in a reactor
‒ please read the instructions for your media
carefully.
5
6
7
4
Biopellets may initially clump during break-in. Turn off
the pump and allow the clumps to settle at the bottom
of the reactor. Gently shake the reactor to break up
clumps. Once the pellets go through this initial
break-in process, they generally require no further
action.
For media designed to be fully fluidized, the
reactor should be filled no more than 2/3 full to
allow the media room to move around. With heavy
or fine media, you may need to add less.
(1)
FR-S / FR-M
FR-S
(1) Main media reactor body and lid
(2) Pump: Sicce Syncra Nano
(3) Sponges *4
FR-M
(1) Main media reactor body and lid
(2) Pump: Sicce Micra
(3) Sponges *4
Turn counterclockwise to release the lid
To fill in the media:
(2) Pick up the upper sponges to fill in the media.
(3) Put back the sponges.
(could be skipped for Biopellet)
(4) Turn clockwise to tighten the lid.
Wash your media before you use it. It is recommended
that biopellets are soaked for 24 hours in aquarium
water before use. Start with 25% of the total amount
of biopellets then add 25% more weekly.
Sponges are not
necessary for Biopellet,
if you are going to use
Biopellet, you can pick
up all the sponges.
Do not over-tighten.
You can change the order of the sponges depends
on media size. Original setting (top-bottom):
coarse - fine - fine - coarse
[email protected]om
www.jnsaquaria.com

Warranty
JNS warrants all JNS products to be free from manufacturing defects for one year
from the original purchase date when purchased through an authorized JNS
retailer. This warranty does not cover any damages caused by misuse, neglect,
alterations, or improper handling / transport / maintenance / installation.
Physical damages are not covered by the warranty. JNS does not cover personal
injury, personal loss, or other damages associated with the use of our products. In
order to request warranty service, please email us at [email protected]om. A
purchase receipt is required for any warranty service. Products requiring
warranty service must be returned to JNS. You are responsible for the cost of
shipping a warranty claim to JNS and any damages that may occur during transit.
Once a returned product has been inspected, it will be repaired or exchanged at
our discretion and returned to you. International and/or expedited shipping are
not covered under your JNS warranty.
(1) The pump must be completely submerged
underwater when in use.
(2) Attachment with a magnet holder for a glass
thickness up to 10mm (3/8")
Please discard the
cardboard between
the magnets before
use.
Make sure the
O-ring is in
position.
8Select a suitable place to set your media
reactor:
(1) Set the input control dial on the pump to its
lowest setting.
(2) Plug in the pump. Adjust the flow rate
with the input control dial.
9To Start
FR-M
FR-M
FR-S
FR-S
Put the wire here
TO AVOID DANGER, KEEP THE POWERFUL MAGNETIC
MOUNT AWAY FROM BABIES AND CHILDREN.
-
+
+ -
11 Regular maintenance of the pump will ensure
long life and maximum performance:
recommended every 3 months. Disassemble the
pump by following steps to clean:
10 For best performance, please clean the reactor
and sponges regularly.
1. Pull out the pump from the bottom.
1. Pull out the pump from the bottom.
2. Pull out cover of the pump.
2. Separate the cover from the pump.
3. Pull out the rotor and sponge.
3. Pull out the rotor.
How to remove the limescale?
NO OTHER CHEMICALS, soak in a mixture of
1 part water and 1 part vinegar (citrin acid
also available) for at least 24 hours. Once
you finish, please rinse with warm water.