Jobsite V-12/AW User manual

For Precise Volume Adjustment
in all Weather Conditions
12 STEP ALL WEATHER WALL MOUNT VOLUME CONTROL V-12/AW
DATA SHEET

V-12/AW
12 STEP ALL WEATHER WALL MOUNT VOLUME CONTROL
FEATURES
• Includes standard faceplates
• Includes weather resistant gasket and stainless steel hardware
• Safely connect up to eight speaker pairs to a single amplifier or receiver
•UL listed to comply with local building codes
• Stylish indicator knob
• 12 step make before break volume control switch design
INSTALLATION FRIENDLY DESIGN:
• Accepts up to 14 gauge wire
• Snap and lock connector secures wire in place without the use of a
screwdriver
SPECIFICATIONS
• High power rating: 100 watts per channel RMS 200 watts peak
•Adjustable impedance: 1x, 2x, 4x, 8x settings
• Total attenuation: 54dB maximum
• V-T4M muting volume control connection terminal recommended
WIRING REQUIREMENTS
• 2 individual runs of 2-conductor 14-18 gauge speaker wire or 1 run
of 4 conductor
• V-T8 volume control connection terminal recommended
MOUNTING:
• Fits most single gang junction boxes, weather resistant gasket included
DIMENSIONS:
• 1-5/8” wide x 2-5/8” high x 2-9/16” deep
• Depth behind faceplate: 2-9/16”
•Faceplate Dimensions: 2-3/4” wide x 4-1/2” high
WARRANTY:
• 10 year limited
12 STEP ALL WEATHER WALL MOUNT VOLUME CONTROL V-12M/AW
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P866.4JB.SITE (866.452.7483)
F305.238.0185
WWW.JOBSITESYSTEMS.COM

PREPARING FOR INSTALLATION:
If you are installing the V-12/AW into an existing wall, take time to consider any
possible obstructions which may be hidden inside the wall, such as wood or
metal studs, electrical, telephone or other types of wiring, plumbing, AC or
heating conduit. Count the number of pairs of 4-ohm speakers and the number
of pairs of 8-ohm speakers you are connecting. Count pairs of 6-ohm speakers
as 4-ohm pairs. Determine the correct switch position from the impedance
charts in the owner’s manual.
INSTALLATION:
1. Identify the Speaker wire and Amplifier wire. Label the wires for future
reference.
2. Strip 1/4" of insulation from the end of each wire. Tightly twist the end of
each wire until no frayed ends remain.
3. Locate the snap and lock connectors and remove them if they are
plugged in.
4. Use a small flathead screwdriver or your thumb to raise the locking tabs,
exposing the holes on the connector.
5. Insert wire into the appropriate hole and snap down the locking tabs.
6. Insert the smooth side of the connector plug into the smooth side of the
V-12/AW socket.
7. Install the V-12/AW into the device ring.
8. Set the Impedance Magnification Switch as determined by the impedance
charts.
9. Set the switches, on all of the controls, to the same position (1x, 2x, 4x,
or 8x).
10. Fasten the cover plate.
V-12/AW INSTALLATION DIAGRAM
12 STEP ALL WEATHER WALL MOUNT VOLUME CONTROL V-12/AW
Speakers
Stereo Receiver
V-12/AW
V-12/AW
Side View
Output to
Speakers
Input From
Amplifier
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P866.4JB.SITE (866.452.7483)
F305.238.0185
WWW.JOBSITESYSTEMS.COM
©2004 Niles Audio Corporation. JobSite,
Pure Custom and Niles are registered
trademarks of Niles Audio Corporation
and the JobSite Logo is a trademark of
Niles Audio Corporation. JSV12AWPDF
Specifications subject to change without notice.