Jobsite V-12M/AWE User manual

For Precise Volume Adjustment
with Programmable Muting
in All Weather Conditions
12 STEP MUTING ALL WEATHER ENCLOSED VOLUME CONTROL V-12M/AWE
DATA SHEET

V-12M/AWE
12 STEP MUTING ALL WEATHER ENCLOSED VOLUME CONTROL
FEATURES
• Includes PVC weatherproof housing and stainless steel hardware
• Programmable circuit mutes selected speakers upon system turn-on
• Safely connect up to eight speaker pairs to a single amplifier or receiver
•UL listed to comply with local building codes
• Stylish indicator knob
• 12 step make before break volume control switch design
INSTALLATION FRIENDLY DESIGN:
• Accepts up to 14 gauge wire
• Snap and lock connector secures wire in place without the use of a
screwdriver
• Mounts easily to any surface or directly on _” PVC conduit
SPECIFICATIONS
•High power rating: 100 watts per channel RMS 200 watts peak
• Adjustable impedance: 1x, 2x, 4x, 8x settings
• Total attenuation: 54dB maximum
• V-T4M muting volume control connection terminal recommended
WIRING REQUIREMENTS
• 2 individual runs of 2-conductor 14-18 gauge speaker wire or 1 run of
4 conductor
• V-T4M muting volume control connection terminal recommended
MOUNTING:
•Surface mount PVC single gang enclosure (included), mounts on PVC conduit
DIMENSIONS:
• 1-5/8” wide x 2-5/8” high x 2-9/16” deep
•Depth behind faceplate: 2-9/16”
• Faceplate Dimensions: 2-3/4” wide x 4-1/2” high
WARRANTY:
• 2 year limited
12 STEP MUTING ALL WEATHER ENCLOSED VOLUME CONTROL V-12M/AWE
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P866.458.7483 (4JB-SITE)
F305.238.0185
WWW.JOBSITESYSTEMS.COM

PREPARING FOR INSTALLATION:
Consider the most convenient location to mount the V-12M/AWE. Use the PVC
junction box (supplied), mounted atop a PVC conduit through which the wires
will run. Count the number of pairs of 4-ohm speakers and the number of pairs
of 8-ohm speakers you are connecting. Count pairs of 6-ohm speakers as 4-ohm
pairs. Determine the correct switch position from the impedance charts in the
owner’s manual.
INSTALLATION:
1. Identify the Speaker wire, Amplifier wire and 12V wire. Label the wires for
future reference.
2. Run the necessary wiring up through the conduit and the opening at the base
of the enclosure.
3. Mount the entire enclosure atop the PVC conduit. Secure the enclosure with
galvanized mounting screws.
4. Strip 1/4" of insulation from the end of each wire. Tightly twist the end of
each wire until no frayed ends remain.
5. Locate the snap and lock connectors and remove them if they are plugged in.
6. Use a small flathead screwdriver or your thumb to raise the locking tabs,
exposing the holes on the connector.
7. Insert each wire into the appropriate hole and snap down the locking tabs.
8. Insert the smooth side of the connector plug into the smooth side of the
V-12M/AWE socket.
9. Locate the 2-pin 12V connector.
10. Insert each 12V wire into the appropriate hole on the connector.
11. Use a small flathead screwdriver to tighten the screws in place.
12. Install the V-12M/AWE into the all-weather enclosure.
13. Set the Impedance Magnification Switch as determined by the
impedance charts.
14. Set the switches, on all of the controls, to the same position
(1x, 2x, 4x, or 8x).
15. Fasten the cover plate.
V-12M/AWE INSTALLATION DIAGRAM
12 STEP MUTING ALL WEATHER ENCLOSED VOLUME CONTROL V-12M/AWE
Speakers
Stereo Receiver
V-12M/AWE
V-12M/AWE
Side View
Output to
Speakers
Input From
Amplifier
V-T4M
12V DC Power Supply Plugged
into an Unswitched AC Outlet
JOBSITE SYSTEMS
12331 SW 130 STREET
MIAMI, FL 33186
P866.458.7483 (4JB-SITE)
F305.238.0185
WWW.JOBSITESYSTEMS.COM
©2004 Niles Audio Corporation. JobSite,
Pure Custom and Niles are registered
trademarks of Niles Audio Corporation
and the JobSite Logo is a trademark of
Niles Audio Corporation. JSV12MAWEPDF
Specifications subject to change without notice.