Johnson Controls TIWM006B22S User manual

P5417089
Operation
Manual
INVERTER-DRIVEN
MULTI-SPLIT SYSTEM
HEAT PUMP
AIR CONDITIONERS
IMPORTANT:
READ AND UNDERSTAND
THIS MANUAL BEFORE
USING THIS HEAT PUMP
AIR CONDITIONER.
KEEP THIS MANUAL FOR
FUTURE REFERENCE.
Type Model
Wall Mount
TIWM006B22S
TIWM008B22S
TIWM012B22S
TIWM015B22S
TIWM018B22S
TIWM024B22S
TIWM030B22S

P5417089 i
Important Notice
●Johnson Controls Inc. pursues a policy of continuing improvement in design and performance in its
products. As such, Johnson Controls Inc. reserves the right to make changes at any time without
prior notice.
●Johnson Controls Inc. cannot anticipate every possible circumstance that might involve a potential
hazard.
●This heat pump air conditioning unit is designed for standard air conditioning applications only.
Do not use this unit for anything other than the purposes for which it is intended.
●The installer and system specialist shall safeguard against leakage in accordance with local codes.
The following standards may be applicable, if local regulations are not available. International
Organization for Standardization: (ISO 5149 or European Standard, EN 378). No part of this manual
may be reproduced in any way without the expressed written consent of Johnson Controls Inc.
●This heat pump air conditioning unit is operated and serviced in the United States of America and
comes with a full complement of the appropriate Safety, Danger, Caution, and Warnings.
●If you have questions, please contact your distributor or contractor.
●This manual provides common descriptions, basic and advanced information to maintain and service
this heat pump air conditioning unit that are operable for other models as well.
● This heat pump air conditioning unit is designed for a specic temperature range.
For optimum performance and long life, operate this unit within the range limits according to the table
below.
●This manual should be considered as a permanent part of the air conditioning equipment and should
remain with the air conditioning equipment.
Temperature
Maximum Minimum
Cooling
Operation
Indoor 89oF DB/73oF WB (32oC DB/23oC WB) 69oF DB/59oF WB (21oC DB/15oC WB)
Outdoor 118oF DB (48oC DB) * 14oF DB (-10oC DB) *
Heating
Operation
Indoor 80oF DB (27oC DB) 59oF DB ( 15oC DB)
Outdoor 59oF WB (15oC WB) * -4oF WB (-20oC WB) *
DB: Dry Bulb, WB: Wet Bulb
* The temperature may change depending on the outdoor unit.

ii P5417089
TABLE OF CONTENTS
1. Introduction .....................................................................................................................................................1
2. Safety Instructions ..........................................................................................................................................1
3. Before Operation.............................................................................................................................................5
3.1 Operating Range ....................................................................................................................................5
3.2 Efcient Use of Indoor Unit.....................................................................................................................5
3.3 Efcient Use of Cooling and Heating......................................................................................................6
4. Name of Parts and Indications for Safety Consideration ................................................................................7
4.1 Wall Mount Type.....................................................................................................................................7
4.2 Wired Controller (CIW01) .......................................................................................................................9
4.3 Wireless Controller (CIR01) .................................................................................................................10
5. Operation Method ......................................................................................................................................... 11
5.1 Wired Controller (CIW01) ..................................................................................................................... 11
5.1.1 Basic Operation .......................................................................................................................... 11
5.1.2 Cooling / Heating / Fan Operation ..............................................................................................12
5.1.3 Temperature Setting ...................................................................................................................13
5.1.4 Fan Speed ..................................................................................................................................13
5.1.5 Operation....................................................................................................................................14
5.1.6 Louver Swing Direction...............................................................................................................15
5.1.7 Comfort Setting...........................................................................................................................17
5.1.8 Automatic Heating/Cooling Operation ........................................................................................18
5.1.9 Setback Operation......................................................................................................................18
5.2 Wireless Controller (CIR01) .................................................................................................................19
5.2.1 Operation Mode (Cooling, Heating, Dry and Fan Operation) .....................................................19
5.2.2 Temperature, Fan Speed and Air Flow Direction Setting............................................................21
5.2.3 Automatic Cooling/Heating Mode ...............................................................................................22
5.2.4 Timer Setting ..............................................................................................................................24
5.2.5 Louver Swing Direction...............................................................................................................25
5.2.6 Emergency Operation.................................................................................................................27
5.2.7 Other Indications.........................................................................................................................28
5.2.8 Identifying Indoor Units Installed Side by Side ...........................................................................29
5.2.9 Handling Wireless Controller ......................................................................................................30
6. Automatic Control .........................................................................................................................................31
7. Maintenance .................................................................................................................................................32
7.1 Daily Maintenance................................................................................................................................32
7.1.1 Cleaning Air Filter .......................................................................................................................32
7.1.2 Maintenance for Flat Panel.........................................................................................................34
7.2 Maintenance Prior to and After Use ....................................................................................................35
7.3 Replacing Batteries (CIR01).................................................................................................................35
8. Troubleshooting ............................................................................................................................................36
8.1 This is Not Abnormal ............................................................................................................................36
8.2 Before Contact .....................................................................................................................................37
8.3 Contact Distributor................................................................................................................................38
8.4 Alarm Code ..........................................................................................................................................39

P5417089 1
1. Introduction
2. Safety Instructions
Signal Words
Indicates a hazardous situation that, if not avoided, could result in death or serious
injury.
Indicates a hazardous situation that, if not avoided, could result in minor or moderate
injury.
Indicates information considered important, but not hazard-related (for example,
messages relating to property damage).
General Precautions
To reduce the risk of serious injury or death, read these instructions thoroughly
and follow all warnings or cautions included in all manuals that accompanied the
product and are attached to the unit. Refer back to these safety instructions as
needed.
● This system should be installed by personnel certied by Johnson Controls, Inc. Personnel must be qualied
according to local, state and national building and safety codes and regulations. Incorrect installation could
cause leaks, electric shock, re or explosion. In areas where Seismic Performance requirements are
specied, the appropriate measures should be taken during installation to guard against possible damage
or injury that might occur in an earthquake. If the unit is not installed correctly, injuries may occur due to a
falling unit.
●Use appropriate Personal Protective Equipment (PPE), such as gloves and protective goggles and, where
appropriate, have a gas mask nearby. Also use electrical protection equipment and tools suited for electrical
operation purposes. Keep a wet cloth and a re extinguisher nearby during brazing. Use care in handling,
rigging, and setting of bulky equipment.
●When transporting, be careful when picking up, moving and mounting these units. Although the unit may
be packed using plastic straps, do not use them for transporting the unit from one location to another. Do
not stand on or put any material on the unit. Get a partner to help, and bend with your knees when lifting to
reduce strain on your back. Sharp edges or thin aluminum ns on the air conditioner can cut ngers, so wear
protective gloves.
●Do not touch or adjust any safety devices inside the indoor or outdoor units. All safety features, disengagement,
and interlocks must be in place and functioning correctly before the equipment is put into operation. If these
devices are improperly adjusted or tampered with in any way, a serious accident can occur. Never bypass or
jump-out any safety device or switch.
Read this manual carefully before working with this product.
Keep this information with the product.
● For details on wiring between the indoor unit and the outdoor unit, refer to the installation and maintenance
manual for the outdoor unit.
● For details on the optional controller, refer to the installation and maintenance manual for that optional
controller module.
● For details on each optional part, refer to the installation and maintenance manual for each optional part.
● For central controller, refer to the installation and maintenance manual for the central controller.
Forward this manual and the warranty registration instructions to the next team of installers and then users.
Ask them to keep this manual with the air conditioning unit.
(Refrigerant Piping Work) (Electrical Wiring Work) (Ref. Charge Work) (Test Run) (User)

2 P5417089
●Before servicing, turn-OFF the power source and use accepted lockout and tag out procedures at all main
switches.
●This unit is pressurized. Never loosen threaded joints while the system is under pressure and never open
pressurized system parts.
●Johnson Controls will not assume any liability for injuries or damage caused by not following steps outlined or
described in this manual. Unauthorized modications to Johnson Controls products are prohibited as they…
◦May create hazards that could result in death, serious injury, equipment damage or property damage;
◦Will void product warranties;
◦ May invalidate product regulatory certications;
◦May violate OSHA standards;

P5417089 3
Operation
● Do not insert ngers or objects into air inlet/outlet. Injury can result from rotating fan blades or energized
electrical components.
● Do not touch the wired or wireless controller with wet hands. It can result in failure of the wired or
wireless controller or an electrical shock.
● Hair spray, insecticides, lacquers, and other pressurized substances should not be used within 3.3ft (1m)
of any air conditioning unit. It can react with energized electrical components and cause re.
● Do not install the indoor unit anywhere discharge airow can pass directly toward nearby heating
equipment (space heaters). It may interfere with the combustion process in these units.
● Air circulation should be optimized to achieve the best distribution pattern and not settle into isolated
pockets that can make people uncomfortable.
● When the indoor unit is operating with heating equipment, ventilate a room sufciently. Any leaked
refrigerant gases that happen to come into contact with any heat source can become toxic on contact and
can cause suffocation in the immediate area.
● Shut down at the main power source if the Ground Fault Circuit Interrupter (GFCI) activates frequently.
Contact your distributor or contractor immediately. Failure to act accordingly can result in serious injury
and damage to the unit.
● If you smell anything burning, shut down the unit and turn OFF the power at the main power source.
Contact the re department and your installer or electrical contractor.
● Make sure that a test for leakage of refrigerant gases is performed. The refrigerant used for this unit (HFC
R410A), is a non-ammable, non-toxic, and odorless gas. However if refrigerant should leak and make
contact with sparks and re; then toxic gas is generated. Also, because the uorocarbon is heavier than
air, the oor surface will be lled with it, which can cause suffocation.
If uorocarbon gas should leak, turn OFF all heating equipment and ventilate the room immediately. Mop
down or vacuum oor areas of residual toxic particulate.
● Do not operate indoor units with the electrical box and switch panel open and exposed. Incidental contact
with energized components can prove fatal.
● When a wireless controller is used, put a distance of at least 3.3ft (1m) between the indoor unit and
electric lighting. If not, the receiver part of the unit may be difcult to receive operation commands due to
effect of the electric lighting.

4 P5417089
● When the at panel is opened (closed) or the air lter is attached (removed), hold them rmly. If not, it
may cause falling or injury.
About Wireless Controller
● Pay attention to the following to use the batteries correctly. If not, it may cause liquid spill or burst.
1. Never use new and old batteries together.
2. Never use the different types of batteries (for example manganese battery and alkaline
battery) together.
3. When the wireless controller is not used over a prolonged period of time (more than 2 or 3 months),
remove the batteries from the wireless controller.
● After removing the old batteries, wait 5 or more seconds before inserting the new ones.
Repair / Relocation / Removal
Others
● Turn OFF all power at the main power source before performing maintenance work. Failure to do so can
result in damage to internal components with severe or fatal electrical shock.
● Insulate all electrical components and connections from exposure to moisture. Failure to do so can result
in an electrical short, re.
● Do not tamper with or attempt to "repair" electrical wiring or connections. Call your installer or electrical
contractor. Serious or fatal injury can occur.
● Perform all maintenance work on a rm and stable platform to minimize the risk of injury.
● Do not attempt to "clean" indoor unit components with liquid or powdered cleaning agents during
maintenance. Electric shock, sparks, ame, and serious or fatal injury can occur.
● System piping is charged with refrigerant and highly pressurized.
● When the air conditioner is to be repaired, transported to a new location or removed, contact your
distributor or contractor. Use the specied refrigerant indicated on the labels of outdoor unit.
Do not change the unit with anything other. If the repair and the installation are not completed, it may
cause electrical shock or re.

P5417089 5
3. Before Operation
Power is turned on. Apply power to the outdoor unit(s) at least 12 hours prior to operation of the
system for preheating of the compressor oil. Make sure that the outdoor unit is not covered with
snow or ice. If it is, remove it by using hot water that is approximately 122oF (50oC).
If the water temperature is higher than 122oF (50oC), it will cause damage to plastic parts.
● Turn OFF the main power switch when the system is stopped for a long period of time.
If the main switch is not turned OFF, electricity is consumed because the oil heater is always energized
during compressor stopping.
● When the system is started after a shutdown longer than approximately 3 months, it is recommended that
the system be checked by your service contractor.
NOTICE
3.2 Efcient Use of Indoor Unit
● Do not leave a window or a door open.
The operating efciency is decreased.
It may cause condensation of the indoor unit. Ventilate a room sufciently.
● Attach a curtain or a blind to a window.
Blocking direct sunlight into a room will increase efciency.
● Do not use heat equipment during the cooling operation as much as possible.
The cooling efciency is decreased. It may cause condensation and dew drops.
● Use a circulator if warm air stays around the ceiling.
Comfort increases. Contact your distributor for details for using a circulator.
● Turn OFF the main power source if the indoor unit is not to be used for a long period.
The standby electricity charges will have to be paid even if the indoor unit is unused.
3.1 Operating Range
This heat pump air conditioner is designed for the following temperatures. Operate the heat pump air
conditioner within this range.
Temperature
Maximum Minimum
Cooling
Operation
Indoor 89oF DB/73oF WB (32oC DB/23oC WB) 69oF DB/59oF WB (21oC DB/15oC WB)
Outdoor 118oF DB (48oC DB) * 14oF DB (-10oC DB) *
Heating
Operation
Indoor 80oF DB (27oC DB) 59oF DB ( 15oC DB)
Outdoor 59oF WB (15oC WB) * -4oF WB (-20oC WB) *
DB: Dry Bulb, WB: Wet Bulb
* The temperature may change depending on the outdoor unit.

6 P5417089
3.3 Efcient Use of Cooling and Heating
(1) Airow Direction
The appropriate air outlet angle is approx. Aoas shown
in the table. If the cooling is not sufcient, change the
airow direction. Pay attention to condensation, which
may occur due to a prolonged cooling operation with
low louver angle.
(Refer to Sections 5.1.6 and 5.2.5 for details.)
(2) Airow Volume
“AUTO” is usually used.
(1) Airow Direction
The appropriate air outlet angle is approx. Aoas shown
in the table. If the heating is not sufcient, change the
airow direction.
(Refer to Sections 5.1.6 and 5.2.5 for details.)
(2) Airow Volume
“AUTO” is usually used.
COOLING HEATING
NOTE
About Multi-Split System
When the number of indoor unit or the operating mode is changed, the air outlet temperature may be
changed and the indoor temperature is changed. In this case, set as follows.
● During Cooling: Lower slightly the temperature setting.
● During Heating: Raise slightly the temperature setting.
Unit Type A Step
TIWM006B22S ~ 012B22S 30 3
TIWM015B22S ~ 030B22S 32 4
Unit Type A Step
TIWM006B22S ~ 012B22S 55 7
TIWM015B22S ~ 030B22S 50 7
Range of Air Outlet Angle
Air Outlet Angle
Ao
Air Outlet Angle
Range of
Air Outlet Angle
Ao

P5417089 7
4. Name of Parts and Indications for Safety Consideration
Safety labels are afxed to the indoor unit in order to ensure safe use.
Read and understand this manual before using the indoor unit.
Indoor Unit
Air Outlet
Louver
Flat Panel
(The air lter is
attached inside.)
Wired Controller or
Wireless Controller
(Option)
Location of Indoor Unit Model
Indication
● It is indicated on the unit nameplate
attached at bottom left.
4.1 Wall Mount Type
Air Inlet
Electrical Hazard
Located on electrical
box cover.
Front Cover Panel
WARNING Label
Safety Label ●Attached to the part indicated by .
WARNING Label
Receiver and Indicator
Indicator
Receiver
Indicator
Receiver
TIWM006B22S, TIWM008B22S
and TIWM012B22S
TIWM015B22S, TIWM018B22S
TIWM024B22S and TIWM030B22S
: TIMER
: FILTER/DEFROST
: RUN

8 P5417089
NOTICE
● Wall mount models: either a wired or a wireless controller is available. When a centralized controller is
connected, restrictions are in place limiting operation of indoor units with a single wireless controller or
using wired and wireless controllers together. Contact your distributor or contractor for details.
● The indicator “ ” of this indoor unit is activated even when the wired controller is used. The indication
for timer settings is indicated on the wired controller only.
● To utilize the wired and wireless controller together, an optional receiver kit is required.

P5417089 9
The following is an example of how the CIW01 is utilized. If other models of the controller are used, operate
the unit according to the manual for that controller.
Display Part
OK
Menu
Back/Help ECO
On/Off
A/C
MODE SPEED TEMP
COOL
LOUV. Adj.
Meeting Room
LOUV.
FLTR
Cold draft rest.
Filter Sign Indicator
FLTR
is displayed at the set period for
lter cleaning.
Operation Lock Indicator
is displayed when the operation
lock function is set. *
Schedule Timer Indicator
is displayed when the schedule
timer function is set. *
Directional Key Enter Key
On/Off Switch
Run Indicator
Illuminates while the
unit is operating, and it
ashes during abnormal
conditions.
Operation Mode
Indicator
“HEAT” and “AUTO” are
indicated only for the
heat pump type models.
Operation Guide
Indicator
“Central Control” is
indicated while the
controller operation is
prohibited.
Operation Part
ECO Switch *
Back/Help Switch
To return to the previous
screen.
Menu Switch *
To display Menu.
Swing Louver Indicator
Fan Speed Indicator
Room Name
Indicator *
The example below references the control panel and all
adjustable settings. The wired controller display may be
different during actual operation.
Setting Temperature
Indicator
4.2 Wired Controller (CIW01)
NOTE
* For detailed descriptions, refer to the "Operation Manual" for the wired controller.
Cold Draft Rest
Indicator
is displayed when the
comfort setting is set.

10 P5417089
● This controller is used to send commands about operation mode timer settings and so on, to the indoor unit.
Face the transmitter of the controller toward the receiver of the indoor unit and press the switch to send
commands to indoor unit.
● The effective transmission range limit is approximately 19.7ft (6m). The effective distance for transmitting
shortens if the transmitter is not perpendicular to the receiver or if there is other electronic interference in the
room.
● Use the receiver kit and the indoor unit that are supported by this controller.
● Reset Switch
● Transmitter
Point the transmitter towards the receiver of the indoor unit when sending
commands. The transmitting indication on the LCD flashes when sending commands
.
● Transmitting Indication: It will turn ON when sending commands by infrared rays.
● LCD (Liquid Crystal Display)
The set temperature, timer operation, position of air louver, operation mode,
air flow mode, etc., are indicated.
NOTE:
The diagram of the display shown on the left is for explanation purposes only.
The display will differ during actual operation.
● Fan Speed Switch
Press this switch to select the fan speed. By repeatedly pressing the button,
the setting will change sequentially through LOW, MED, HIGH, HIGH2 and AUTO.
* Depending on the setting for selecting the function, it is possible to set the
ON/OFF for the Fan Speed AUTO.
1 Step 2 Step 7 Step
Auto Swing
● On Switch
Operation of the unit can be started by pressing this switch.
● Off Switch
Operation of the unit can be stopped by pressing this switch.
● Mode Selection Switch
By repeatedly pressing the mode switch, the unit cycles through
the different operating modes in the order of FAN, COOL, HEAT, AUTO.
* Depending on the setting for selecting the function, it is possible to set
the ON/OFF for AUTO, HEAT and DRY display.
● Louver Angle Switch
The airflow angle and auto-louver operation can be set by this switch.
When pressing the switch, the angle is changed in the following order.
(In COOL or HEAT or AUTO operation modes, steps 1-5 and Auto swing are
available.)
● Filter Sign Reset Switch
When it is time to perform the filter cleaning, the filter indicator turns ON.
The alarm sound can be cancelled temporarily by pressing the button.
● Temp. Switch
The setting temperature can be adjusted using this switch.
By pressing “ ∆ ”, the temperature will increase by 1°F (0.5°C or 1°C) at a time.
By pressing “
∆
”, the temperature will decrease by 1°F (0.5°C or 1°C) at a time.
* Depending on the setting for selecting the function, the temperature range
can have a unit of 1°F (0.5°C or 1°C).
● Timer Switches
Used to set the timer.
The set time can be changed by pressing “On Timer” or “Off Timer”.
The timer can be set from 0.5 to 23 hours. When 0.5 to 9.5 hours, the unit is set
set as 30 min. at a time, and when 10 to 23 hours, the unit is set as 1 hour
at a time.
LOW → MED → HIGH → HIGH2 → AUTO
3 Step 4 Step 5 Step 6 Step
NOTE:
When the wireless controller is prohibited by central controller, this function is
disabled even though the indoor unit is set with the wireless controller and the
buzzer sounds.
4.3 Wireless Controller (CIR01)

P5417089 11
5. Operation Method
5.1 Wired Controller (CIW01)
5.1.1 Basic Operation
OK
Menu
Back/Help ECO
On/Off
A/C
MODE SPEED TEMP
COOL
LOUV. Adj.
Meeting Room
LOUV.
FLTR
Motion Sensor ON
Avoid
Item
Selection
By pressing “ ”or “ ”, the icon “ ”
moves between “MODE”, “SPEED”,
“LOUV.” and “TEMP”.
OK
Menu
Back/Hel
p
Change of
Settings
With “MODE”, “SPEED”, “LOUV.” or
“TEMP” selected, press “ ” or “ ”.
The setting is changed.
OK
Menu
Back/Hel
p

12 P5417089
5.1.2 Cooling / Heating / Fan Operation
* Cooling Operation: To decrease the room temperature.
* Heating Operation: To increase the room temperature.
* Dry Operation: To decrease the humidity in the room.
* Fan Operation: To circulate the air in the room.
Heating Operation is for VRF systems only and is not available for typical systems.
● Dry operation may not be performed properly if there are other heat sources that exceed the capacity of
the unit.
● In case where the individual setting is operating, decreasing of the humidity during dry operation might be
unavailable.
Before
Operation
Turn ON the power supply.
Turn ON the main power approximately
12 hours before operation in order to
preheat the compressor.
Do not turn OFF the main power of the
indoor unit during heating or cooling
season.
Connecting
1
Press “ ” or “ ” to select “MODE”.
OK
Menu
Back/Hel
p
2
By pressing “ ” or “ ”, the mode is
changed as follows.
OK
Menu
Back/Hel
p
● Automatic cooling/heating operation (AUTO) requires an extra setting. Contact your distributor or
contractor for details.
FAN(AUTO)DRYHEATCOOL
Function

P5417089 13
5.1.3 Temperature Setting
5.1.4 Fan Speed
1
Press “ ” or “ ” and select “TEMP”.
OK
Menu
Back/Hel
p
2
By pressing “ ”, the temperature is
increased by 1°F (0.5oC or 1oC).
(Max. 86°F (30oC)
By pressing “ ”, the temperature is
decreased by 1°F (0.5oC or 1oC).
COOL, FAN operation: Min. 66°F (19oC)
HEAT operation: Min. 62°F (17oC)
OK
Menu
Back/Hel
p
●In case the optional function “Automatic Reset of Setting Temperature” is set:
Even if changing the setting temperature on the wired controller, it automatically returns to the
temperature set by “Automatic Reset Temperature” after a set time.
●Minimum and maximum temperature setpoint limits can be congured by selecting a cooling lower limit
and heating upper limit in the “Function Selection” mode of the wired controller’s Test Run Menu.
●Contact your distributor or contractor for details on optional functions “Automatic Reset of Setting
Temperature,” “Cooling Lower Limit for Setting Temperature” and “Heating Upper Limit for Setting
Temperature.”
1
Press “ ” or “ ” and select “SPEED”.
OK
Menu
Back/Hel
p
2
By pressing “ ” or “ ”, the fan speed is
changed as follows.
OK
Menu
Back/Hel
p
● During the dry operation, the fan speed is automatically changed to “LOW” and cannot be changed to
any other fan speed. (“LOW” is NOT displayed on Liquid Crystal Display (LCD) at this time. The present
setting condition is displayed on the LCD.)
● The fan speed setting “HIGH 2” may not be available depending on the indoor unit type.
AUTO HIGH 2
HIGH MED LOW

14 P5417089
5.1.5 Operation
Operation
Start
Press “ ” (On/Off).
The indicator “ ” is turned ON and the
operation is started. OK
On/Off
Temperature/Air Flow Setting
● The setting is stored. Therefore, no daily setting is required. Temperature setpoint and airow settings
are retained after the indoor unit is turned OFF at the controller. In a case where the setting change is
required, refer to Sections 5.1.2 to 5.1.4.
Operation
Stop
Press “ ” (On/Off) again.
The indicator “ ” is turned OFF and the
operation will stop.
OK
On/Off
● The indoor unit fan may continue to operate for up to 2 minutes following the heating cycle to dissipate
residual heat from the indoor unit.

P5417089 15
5.1.6 Louver Swing Direction
1
Press “ ” (On/Off).
Make sure that the operation is started.
Press “ ” or “ ” and select “LOUV.”.
OK
Menu
Back/Hel
p
2
By pressing “ ” or “ ”, the louver
direction is changed as follows.
OK
Menu
Back/Hel
p
NOTE:
When step 6 or step 7 is selected during cooling operation and dry operation, the louver angle is
xed at step 5.
● The louver angle indicated on the LCD and the actual louver angle do not correspond precisely with each other
during the auto-swing mode operation. When the louver is xed, set the louver angle according to the louver
position indicated on the LCD.
● The louver may NOT stop immediately after the switch is pressed.
● For adjustment of vertical blade, refer to next page.
LCD Indication
Air Outlet Angle
Air Outlet Angle
COOL and DRY
FAN
Approx. 15oApprox. 22oApprox. 28oApprox. 35oApprox. 42oApprox. 48oApprox. 55o
Recommended
Angle
HEAT
Approx. 25oApprox. 30oApprox. 35oApprox. 40oApprox. 45oApprox. 50oApprox. 55o
Angle Range
Angle Range
Auto-Swing Range
Auto-Swing Range
Auto-Swing Range
Air Outlet Angle Approx. 15oApprox. 23oApprox. 30oApprox. 38oApprox. 45o
Recommended
Angle
Recommended
Angle
Angle Range
Auto
Swing
Step 1 2 3 4 5 6 7 -
LCD Indication
Auto Swing 12345
67
TIWM006B22S ~ TIWM012B22S
TIWM015B22S ~ TIWM030B22S
: Auto-swing operation
is started. At this time,
the louver icon swings
repeatedly on LCD.
LCD Indication
Air Outlet Angle
Air Outlet Angle
COOL and DRY
FAN
Approx. 10oApprox. 17oApprox. 23oApprox. 30oApprox. 37oApprox. 44oApprox. 50o
Recommended
Angle
HEAT
Approx. 10oApprox. 17oApprox. 23oApprox. 30oApprox. 37oApprox. 44oApprox. 50o
Angle Range
Angle Range
Auto-Swing Range
Auto-Swing Range
Auto-Swing Range
Air Outlet Angle Approx. 10oApprox. 17oApprox. 25oApprox. 32oApprox. 40o
Recommended
Angle
Recommended
Angle
Angle Range
Auto
Swing
Step 1 2 3 4 5 6 7 -

16 P5417089
● Adjusting Vertical Blade
Adjust the vertical blade by hand as shown below.
● Automatic Louver Setting
The swing louver is stopped and moved by controlling the wired controller.
The louver automatically closes when the unit is stopped from the wired controller.
TIWM006B22S ~ TIWM012B22S TIWM015B22S ~ TIWM030B22S
● Louver Angle during Cooling and Dry Operation
The louver angle self-adjusts from its default setting during times of cooling and dry conditions to
prevent condensation buildup. Louver angle changes are not shown on the LCD of wired controller.
● Louver Angle during Heating Operation
The louver angle self-adjusts for heating conditions.
Do not attempt to move the louver by hand as this will damage the automatic louver setting function.
* When the heating operation starts
* When the defrost operation starts
The louver is at a
15-degree angle.
15o
When the discharge
temperature is higher
than 86°F (30°C), the
louver angle automatically
returns to the setting on
the wired controller.
Above louver angle changes are not shown on the LCD of the wired
controller.
NOTICE
Ve
rtical Blade Louver
Louver
Louver
Louver