Mounting instructions
To install the reader, complete the following steps:
1. Pull the cable from the wall through the hole of the mounting plate.
2. Attach the mounting plate to the wall with #6 (3.5 mm) screws. Screw length depends on
wall surface and thickness.
3. For tamper detection, cut the plastic tab from the mounting plate.
4. Fasten the white reflector tab back on the wall.
5. After installing the wiring using the wiring diagrams, insert the hook at the top of the cover
into the mounting plate tab and press the bottom of the cover until the bottom hook
snaps into place.
6. Use the provided Phillip's head screw to secure the bottom of the reader.
Note: If using CAT5 cable, use two wires for GND, and two wires for PWR.
Instructions pour montage
Pour installer le lecteur:
1. Tirez le câble du mur et le passer à travers la plaque de montage.
2. Fixez la plaque de montage au mur en utilisant des vis #6 (3,5 mm). La longueur de vis
requise dépend de la surface et de l'épaisseur du mur.
3. Pour une détection d'anti-sabotage, coupez la languette en plastique à partir de la plaque
de montage.
4. Refixez la languette blanche du réflecteur sur le mur.
5. Après l'installation du câblage conformément aux schémas de câblage, insérez le crochet
en haut du couvercle dans la languette de la plaque de montage et appuyez sur le bas
du couvercle jusqu'à ce que le crochet inférieur s'enclenche.
6. Utilisez la vis à tête Phillips pour fixer la partie inférieure du lecteur.
Note: Si vous utilisez un câble CAT5, utilisez deux fils pour GND et deux fils pour PWR.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by KANTECH could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received including interference that may cause undesired operation.
The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available
from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and oper-
ated with minimum distance 20 cm (7.8 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for sat-
isfying RF exposure compliance.
ISED CANADA STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Oper-
ation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applic-
ables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l 'appareil ne doit pas produire de brouillage, et (2) l
'utilisateur de l 'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d 'en compromettre le fonctionnement.
CAN ICES-3 (B) / NMB-3 (B).
RF Exposure Statement (ISED)
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm (7.6 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Pour se conformer aux exigences de conformité ISED RSS-102 RF exposition, une distance de séparation d'au moins 20 cm doit être maintenue entre l'antenne de cet
appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
Mullion MT
(with or without keypad)
FCC ID: V8515KTMULMTKP2
ISED: 5690B-KTMULMTKP2
Mullion SC
(with or without keypad)
FCC ID: V8515KTMULSCKP2
ISED: 5690B-KTMULSCKP2
Single Gang MT
(with or without keypad)
FCC ID: V8515KTSGMTKP2
ISED: 5690B-KTSGMTKP2
Single Gang SC
(with or without keypad)
FCC ID: V8515KTSGSCKP2
ISED: 5690B-KTSGSCKP2
UL294 Performance Levels and Requirements:
Destructive Attack: Level I (no attack test)
Line Security: Level III via RS-485 communication and EntraPass reader template having Buzzer enabled for Comm fail alarm; Level 1 via Wiegand com-
munication.
Endurance: Level IV (100,000 cycles)
Standby Power: Level I (no integral standby power)
Installation location and wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA 70. There is no maintenance required and there are no
replacement parts required for these devices.
UL 2610 Requirements:
For alarm signals, the end-of-line resistor shall be UL listed 5.6Kohm, 5%, 1/2 W with 18 AWG wire leads six (6) inches minimum. It shall be
securely fastened with no means to open circuit, short to an adjacent circuit node, or cause a risk of electrical shock.
ioSmart readers that are wired to controller’s Wiegand interface and used for arming and disarming shall be configured to mode 8 to enable
Wiegand mode tamper reporting.
For BLE mobile credential installations, BLE v4.2 or higher, Android OS 9.0 or higher, Apple iOS 9 or higher, and EntraPass go Pass 2.00.xx or higher are supported.
