Johnson Controls York YCAL0041-0071 User manual

SERVICE POLICY & PROCEDURES
YCAL0041-0071 50 HZ
START-UP CHECKLIST
Supersedes: Nothing Form 150.66-CL3 (309)
COMMISSIONING
Commissioning of this unit should only
be carried out by YORK Authorized
personnel.
Commissioning personnel should be thoroughly familiar
with the information contained in this literature, in ad-
dition to this section.
Perform the commissioning using the detailed checks
outlined in the EQUIPMENT START-UP CHECK LIST
as the commissioning procedure is carried out.
PREPARATION – POWER OFF
The following basic checks should be made with the
customer power to the unit switched OFF.
Inspection
Inspect unit for installation damage. If found, take action
and/or repair as appropriate.
Refrigerant Charge
Packaged units are normally shipped as standard with a
full refrigerant operating charge. Check that refrigerant
pressure is present in both systems and that no leaks are
apparent. If no pressure is present, a leak test must be
undertaken, the leak(s) located and repaired. Remote
systems and units are supplied with a nitrogen hold-
ing charge. These systems must be evacuated with a
suitable vacuum pump/recovery unit as appropriate to
below 500 microns.
Do not liquid charge with static water in the cooler.
Care must also be taken to liquid charge slowly to avoid
excessive thermal stress at the charging point. Once the
vacuum is broken, charge into the condenser coils with
the full operating charge.
Service and Oil Line Valves
Open each compressor suction, economizer, and dis-
charge service valve. If valves are of the back-seat type,
open them fully (counterclockwise) then close one turn
of the stem to ensure operating pressure is fed to pressure
transducers. Open the liquid line service valve and oil
return line ball valve fully in each system.
Compressor Oil
To add oil to a circuit - connect a YORK hand oil pump
(Part No. 470-10654-000) to the 1/4” oil charging valve
on the oil separator piping with a length of clean hose
or copper line, but do not tighten the are nut. Using
clean oil of the correct type (“F” oil), pump oil until all
air has been purged from the hose then tighten the nut.
Stroke the oil pump to add oil to the oil system. The oil
level should be visible in the bottom half of the sight
glass at shutdown and while running at full load. Ap-
proximately 4-5 gallons is present in the each refrigerant
system, with typically 1-2 gallons in each oil separator.
Oil levels above the top sight glass should be avoided
and may cause excessive oil carryover in the system.
High oil concentration in the system may cause nuisance
trips resulting from incorrect readings on the level sensor
and temperature sensors. Temperature sensor errors may
result in poor liquid control and resultant liquid overfeed
and subsequent damage to the compressor.
Fans
Check that all fans are free to rotate and are not dam-
aged. Ensure blades are at the same height when rotated.
Ensure fan guards are securely xed.
Isolation / Protection
Verify all sources of electrical supply to the unit are
taken from a single point of isolation. Check that the
maximum recommended fuse sizes given in the Techni-
cal Data Section has not been exceeded.

FORM 150.66-CL3 (309)
2JOHNSON CONTROLS
Control Panel
Check the panel to see that it is free of foreign materials
(wire, metal chips, etc.) and clean out if required.
Power Connections
Check that the customer power cables are connected cor-
rectly to the terminal blocks or optional circuit breaker.
Ensure that connections of power cables within the pan-
els to the circuit breaker or terminal blocks are tight.
Grounding
Verify that the unit’s protective ground terminal(s) are
properly connected to a suitable grounding point. Ensure
that all unit internal ground connections are tight.
Supply Voltage
Verify that the site voltage supply corresponds to the
unit requirement and is within limits. Refer to Technical
Data Section in the IOM (150.66-NM3).
PREPARAtIOn – POWER On
Perform the commissioning using the
detailed checks outlined in the EQUIP-
MENT START-UP CHECK LIST as
the commissioning procedure is car-
ried out.
Apply power to the chiller. Turn ON the option panel
circuit breaker if supplied.
The machine is now live!
Switch Settings
Assure the chiller OFF/ON UNIT switch at the bottom
of the keypad is OFF. Place the optional circuit breaker
handle on the panel door to ON. The customer’s discon-
nection devices can now be set to ON.
Verify the control panel display is illuminated. Assure
the system switches under the SYSTEM SWITCHES
Key are in the OFF position.
Compressor Heaters
Verify the compressor heaters are energized. If the am-
bient temperature is above 96°F (36°C) the compressor
heaters must be on for at least 8 hours before start-up
to ensure all refrigerant liquid is driven out of the com-
pressor and the oil. If the ambient temperature is below
86°F (30°C), allow 24 hours.
Water System
Verify the chilled liquid system has been installed cor-
rectly, and has been commissioned with the correct di-
rection of water ow through the cooler. The inlet should
be at the refrigerant piping connection end of the cooler.
Purge air from the top of the cooler using the plugged
air vent mounted on the top of the cooler body.
Flow rates and pressure drops must be within limits.
Refer to Technical Data Section in IOM (150.66-NM3).
Operation outside of these limits is undesirable and
could cause damage.
If mains power must be switched OFF for extended
maintenance or an extended shutdown period, the
compressor suction, discharge and economizer service
stop valves should be closed (clockwise). If there is
a possibility of liquid freezing due to low ambient
temperatures, the coolers should be drained or power
should be applied to the chiller. This will allow the
cooler heater to protect the cooler from freezing down
to –20°F. Before placing the unit back in service, valves
should be opened and power must be switched on (if
power is removed for more than 8 hours) for at least 8
hours (24 hours if ambient temperature is below 86°F
[30°C]) before the unit is restarted.
Flow Switch
Verify a chilled water ow switch is correctly tted in
the customer’s piping on the cooler outlet, and wired into
the control panel correctly using shielded cable.
There should be a straight run of at least 5 pipe diameters
on either side of the ow switch. The ow switch should
be connected to terminals 13 and 14 in the panel.
Temperature Sensor(s)
Ensure the leaving liquid temperature sensor is coated
with heat conductive compound (Part No. 013-00890-
000) and is inserted to the bottom of the water outlet
sensor well in the cooler. This sensor also provides some
freeze protection and must always be fully inserted in
the water outlet sensor well.

FORM 150.66-CL3 (309)
JOHNSON CONTROLS 3
JOB NAME: ______________________________
SALES ORDER #: _________________________
LOCATION: ______________________________
SOLD BY: ________________________________
INSTALLING
CONTRACTOR: ___________________________
START-UP
TECHNICIAN/
COMPANY: _______________________________
START-UP DATE : _________________________
CHILLER MODEL #: _______________________
SERIAL #: ______________________________
CHECKING THE SYSTEM
PRIOR TO INITIAL START (NO POWER)
Unit Checks
1. Inspect the unit for shipping or installation dam-
age.
2. Assure that all piping has been completed.
3. Visually check for refrigerant piping leaks.
4. Open suction line ball valve, discharge line ball
valve, and liquid line valve for each system.
5. The compressor oil level should be maintained so
that an oil level is visible in the sight glass. The oil
level can only be tested when the compressor is
running in stabilized conditions, guaranteeing that
there is no liquid refrigerant in the lower shell of
the compressor. When running, the oil should be
in the bottom half of the sight glass. At shutdown,
the oil level should also be visible in the bottom
half of the oil sight glass.
6. Assure water pumps are on. Check and adjust
water pump ow rate and pressure drop across
the cooler. Verify ow switch operation.
Excessive ow may cause catastrophic
damage to the evaporator.
EQUIPMENT STARTUP CHECKLIST
7. Check the control panel to ensure it is free of
foreign material (wires, metal chips, etc.).
8. Visually inspect wiring (power and control). Wir-
ing MUST meet N.E.C. and local codes.
9. Check tightness of power wiring inside the power
panel on both sides of the motor contactors and
overloads.
10.Check for proper size fuses in main and control
circuits, and verify overload setting corresponds
with RLA and FLA values. Refer to Electrical
Tables in the IOM (150.66-NM3) or unit name-
plate.
11.Assure 120VAC Control Power to TB1 has 15
amp minimum capacity.
12.Be certain all water temp sensors are inserted
completely in their respective wells and are coated
with heat conductive compound.
13.Assure that evaporator TXV bulbs are strapped
onto the suction lines at 4 or 8 o’clock positions
or suction temp. sensors if EEVs are installed.
COMPRESSOR HEATERS
(POWER ON – 24 HOURS PRIOR TO START)
1. Apply 120VAC and verify its value between ter-
minals 5 and 2 of CTB2. The voltage should be
120VAC +/- 10%.
Power must be applied 24 hours prior to
start-up.
Each heater should draw approximately 0.5-1A.
PANEL CHECKS
(POWER ON – BOTH UNIT SWITCHES OFF)
1. Apply 3-phase power and verify its value. Volt-
age imbalance should be no more than 2% of the
average voltage.
2. Apply 120VAC and verify its value on the terminal
block in the Power Panel. Make the measurement
between terminals 5 and 2 of TB1. The voltage
should be 120VAC +/- 10%.
3. Program/verify the Cooling Setpoints, Program
Setpoints, and unit Options. Record the values in
Table 1.

FORM 150.66-CL3 (309)
4JOHNSON CONTROLS
4. Put the unit into Service Mode and cycle each
condenser fan to ensure proper rotation.
5. Prior to this step, turn system 2 off. Connect a
manifold gauge to system 1 suction and discharge
service valves.
Place the Unit Switch in the control panel to the
“ON” position. As each compressor cycles on,
ensure that the discharge pressure rises and the
suction pressure decreases. If this does not oc-
cur, the compressor being tested is operating in
the reverse direction and must be corrected. After
verifying proper compressor rotation, turn the
Unit Switch to “OFF.”
The chilled liquid setpoint may need to
be temporarily lowered to ensure all
compressors cycle “ON.”
This unit uses scroll compressors
which can only operate in one direc-
tion. Failure to observe this will lead
to compressor failure.
6. YCAL0041 - YCAL0071 units only – Turn system
1 “OFF” and system 2 “ON”.
Place the Unit Switch in the control panel to the
“ON” position. As each compressor cycles “ON”,
ensure that the discharge pressure rises and the
suction pressure decreases. If this does not oc-
cur, the compressor being tested is operating in
the reverse direction and must be corrected. After
verifying proper compressor rotation, turn the
Unit Switch to “OFF”.
The chilled liquid setpoint may need to
be temporarily lowered to ensure all
compressors cycle “ON”.
ChECkIng SUPERhEAt AnD SUBCOOLIng
The subcooling temperature of each system can be cal-
culated by recording the temperature of the liquid line
at the outlet of the condenser and subtracting it from
the liquid line saturation temperature at the liquid stop
valve (liquid line saturation temp. is converted from a
temperature/pressure chart).
Example:
Liquid line pressure =
202 PSIG converted to temp. 102°F
minus liquid line temp. - 87°F
Subcooling = 15°F
The subcooling should be adjusted to 15°F at design
conditions.
OPtIOnS
Display Language
Sys 1 Switch
Sys 2 Switch
Chilled Liquid
* Ambient Control
Local/Remote Mode
Control Mode
Display Units
* Lead/Lag Control
* Fan Control
Manual Override
Current Feedback
** Soft Start
** Unit Type
** Refrigerant Type
** Expansion Valve Type
COOLIng SEtPOIntS
Cooling Setpoint
Range
EMS-PWM Max. Setpoint
PROgRAm
Discharge Pressure Cutout
Suct. Pressure Cutout
Low Amb. Temp. Cutout
Leaving Liquid Temp. Cutout
Anti-Recycle Time
Fan Control On Pressure
Fan Differential Off Pressure
Total # of Compressors
* Number of Fans/System
* Unit/Sys Voltage
Unit ID
* Sys 1 Superheat Setpoint
* Sys 2 Superheat Setpoint
tABLE 1 – SEtPOIntS EntRY LISt
* NOT ON ALL MODELS
** VIEWABLE ONLY

1. Record the liquid line pressure and its correspond-
ing temperature, liquid line temperature and
subcooling below:
SYS 1 SYS 2
Liq Line Press = _______ _______ PSIG
Saturated Temp = _______ _______ °F
Liq Line Temp = _______ _______ °F
Subcooling = _______ _______ °F
After the subcooling is veried, the suction superheat
should be checked. The superheat should be checked only
after steady state operation of the chiller has been estab-
lished, the leaving water temperature has been pulled down
to the required leaving water temperature, and the unit is
running in a fully loaded condition. Correct superheat set-
ting for a system is 10°F - 15°F (5.56°C - 8.33°C) 18” (46
cm) from the cooler.
Superheat should typically be set for no less than 10°F
with only a single compressor running on a circuit.
The superheat is calculated as the difference between
the actual temperature of the returned refrigerant gas in
the suction line entering the compressor and the tem-
perature corresponding to the suction pressure as shown
in a standard pressure/temperature chart.
Example:
Suction Temp = 46°F
minus Suction Press
60 PSIG converted to Temp - 34°F
Superheat = 12°F
When adjusting the expansion valve (TXV only), the
adjusting screw should be turned not more than one
turn at a time, allowing sufcient time (approximately
15 minutes) between adjustments for the system and the
thermal expansion valve to respond and stabilize.
The EEV is non-adjustable. Superheat
setpoint is programmable from the
keypad.
Assure that superheat is set at a minimum of 10°F (5.56°C)
with a single compressor running on each circuit.
2. Record the suction temperature, suction pressure,
suction saturation temperature, and superheat of
each system below:
SYS 1 SYS 2
Suction Temp = _______ _______ °F
Suction Pressure = _______ _______ PSIG
Saturation Temp = _______ _______ °F
Superheat = _______ _______ °F
LEAk ChECkIng
 1. Leak check compressors, ttings, and piping to
ensure no leaks.
If the unit is functioning satisfactorily during the initial
operating period, no safeties trip and the compressors
cycle to control water temperature to setpoint, the chiller
is ready to be placed into operation.
©2009 Johnson Controls, Inc. P.O. Box 423, Milwaukee, WI 53203
www.johnsoncontrols.com
Printed in USA 150.66-CL3 (309)
New Release