Johnson Controls HomeLink User manual

1tJ HomeLink ®
Wi reless Control System
NO TE: Some veh i cles may requ i re the i gn iti on to be turned to the second {or "accessory")
pos iti on for programm i ng and/or operat i on of Home link. It isal so recommended that a
new battery be rep l aced in the hand he ld transm i tter of the dev i ce be i ng programmed to
Home link" for qu i cker tra ini ng and accurate transm i ss i on of the rad io frequency. Pl ease
make sure that peop le and ob j ects are out of the way of the mov i ng door or gate when
programm i ng to prevent potent ial harm or damage.
1. For fi rst ti me programm i ng, press and ho ld
the two outer Homelink buttons re l eas i ng on ly
when the Home link i nd i cator li ght beg i ns to
fl ash after 20 seconds . (Do not perform th is
step when programm i ng the add iti ona l
Homelink buttons)
2. Pos iti on the hand-he ld transm itter 1-3 i nches
away from the Home link surface (located on
your vi sor. overhead conso le or mi rror) keep i ng
the Homelink i nd i cator li ght invi ew .
3. Us i ng both hands ,si mu l taneous ly press and ho ld
both the des i red Homelink button and hand
he ld transm itter button. DO NOT re l ease unt il
the Homelink i nd i cator li ght fl ashes sl ow ly and
then rap idly. When the i nd i cator li ght fl ashes
rap idly, both buttons may be re l eased. (The rap id
fl
ash i ng i nd i cates successfu l programm i ng)
N ote: Some gate ope r ato rsand ga r age doo r ope ners
may r eq uire yo u to r ep l ace step #3 withthe ·cycl ing"
pr oced ur en oted inthe ·Gate Ope r ato rand Ca n ad ian
Pr
og ramming" sect ion.
Form #5468 REV. A 10/22/13

4. Press and ho ld the programmed Home link
button and observe the i nd i cator li ght.
• If the i nd i cator li ght is so li d/cont i nuous, pro-
gramm i ng is comp l ete and your dev i ce shou ld
act i vate when the Home link button is pressed
and re l eased .
• If
the i nd i cator li ght bli nks rap idly for 2 sec-
onds and then turns a so li d/cont i nuous li ght,
proceed wi th the follow i ng programm i ng
i nstruct i ons for a ro ll i ng code dev i ce. A second
person may make the follow i ng steps qu i cker
and eas i er.
5. At the garage door opener rece i ver (motorhead
un i t) in the garage, l ocate the "l eam" or
"smart" button (usua lly near where the hang-
i ng antenna wi re is attached to the un i t). If
there isdiffi cu l ty l ocat i ng the tra ini ng button
reference the garage door opener's manua l,
visit our webs i te www . home li nk . com or con-
tact us at 1-800 - 355-3515.
6. Press and re l ease the "l earn" or "smart" but-
ton (the name and co l or of the butt on may
vary by manufacturer) . NOTE : Once the button
is pressed , there are 30 seconds in wh i ch to
initi ate the next step.
7. Return to the veh i cle and fi rm ly press and ho ld
the programmed Homelink button for two
seconds and re l ease. Repeat the "p ress/ho l d/
re l ease" sequence up to 3ti mes to comp l ete
the tra ini ng process.

Homelink shou ld now act i vate your roll i ng code equ i pped dev i ce.
To program additional Homelink buttons, b egin with "programming" step two.
Once programmed , the Home linkWi re l ess Contro l System or the origi na l hand - he ld
transm i tter may be used to act i vate the dev i ce (e.g. garage door. entry l ock , gate, etc.) .
In the even that there are st i ll pr ogramm i ng diffi cu lti es, pl ease contact Home link at
1- 800-355 - 3515 or visit our webs i te at www.home link .com.
Preca ut ions!
Do not use the Home link" Wi re l ess Contro l System wi th any garage door opener that
l acks the safety stop and reverse feature as requ i red by federa l safety standards. ( Th is
i ncludes any garage door opener mode l manufac t ured before Apr il 1, 1982). A garage
door opener that cannot detect an object, si gna li ng the door to stop and reverse , does
not meet current federa l safety standa r ds. Us i ng a garage door opener wi thout these
features i ncreases ri sk of ser i ous inju ry or death. For more i nformat i on , ca ll 1-800 - 355-
351 5 or visit our webs i te at www . home li nk . com .
Reta in the origi na l hand - he ld transm itter for futu re programm i ng procedures ( i. e., new
veh i cle purchase) .It isal. so suggested that upon sa le of the veh icl e, the programmed
Homelink Wi re l ess Contro l System buttons be erased for secur i ty purposes (fo ll ow step 1
inthe·
Programm i ng" port i on of th :s text) . For conven i ence, the hand - he ld transm i tter
of the dev i ce may al so be used at anyti me.
Gate Op erator Programming and Canadian Programming
If programm i ng a garage door opener or gate ,it is adv i sed to unp l ug the dev : ce dur i ng
the "cy cl i ng" pr ocess to prevent poss ible motor bum - up .
Dur i ng programm i ng, your hand - he ld transm i tter may automat i ca lly stop transm itti ng .
Cont i nue to press and ho ld the des ir ed Homelin k button (note steps 2-4 inthe
"Programm i ng" port i on on th is text) wh ile you press and re-press ("cycle") yo ur hand-
he ld transm i tter every two seconds unt il the fr equency si gna l has been l earned. The
i nd i cator li ght wi ll fl ash sl ow ly and then rap idly after seve ral seconds upon successfu l
tra ini ng. If necessary , follow steps 5·7 to comp l ete the tra ini ng for a ro lli ng code dev i ce.

FORM%#5468
Reprogramming a Single Homel i nk ®Button
To program a dev
ic e to HomeLink using a HomeLink button previously trained,
fo ll ow these steps:
1. Press and ho ld the desired pre-programmed Hom eli nk button f or at least
20 seconds (but no long er t ha n 30 seconds) unt il the indi ca tor light be gins to
flash. Without releasing t
he HomeLink button, position t heha nd- he ld tran sm itter
1-3 inc hes a way from t he HomeLink surface keeping t he HomeLink indica tor
li g ht in view.
2. Using both
ha nds, simultaneously press and hold both the desired Home li nk
bu tto n a nd ha nd he ld t ransm i tter bu tto n ( or press a nd "cycl e"- as d esc ri bed in
"Gate and Canad ian Programming"). DO NOT release until the H ome li nk
indicator light flashes sl
ow ly and then rapidly. When the i nd icator light fla sh es
rapidl
y, both buttons may be released. (The rapid flashing indicates su cc essful
programmin
g)
T he previous device has now be en erased and the new devi ce can be activated
by
pu sh ing the Home li nk button that h as ju st been programmed. Howev er , it may
be necessary to fo ll ow steps 5-7 of the "Programmin g' se ct ion to complete the
rolling code
tr aining.This procedure will not aff e ct any other programmed
Home
Li nk buttons.
Erasing Programmed
Homelink ®Buttons
Pr ess and ho ld the tw o outer H ome li nk buttons rele as ing only when the
Home
Li nk indicat or ig ht be gins to flash after 20 seconds. Do not hold f or long er
than 30 seconds. H om eli nk is no w in t he tr ain ( or teaming) mode and can be
programmed at any time beginning with step 2 in t he "Programming" s ec tion of
this tex
t.
Accessories
If you would li ke ad di tional information on t he HomeLink0 Wirele ss Control
System, Home
Li nkcompatible products or to purchase ac cessories, plea se
contact H ome lin k at 1-80 0- 355-3515 or visit o ur website at 1vww .homelink.com.
This d ev ice complies wilh FCC rul es part 15. Operation is sub je ct to the fo llowing two co nditions
(1) This d
ev ice may notcause harmful inte rl eren ce . and (2) This devi ce mu st accept any
interleren
ce th at may be re ce ived including interleren ce th at may cau se un desired operation.
WAR NING: The tran sm itter h as been t es ted and compli es with FC C and IC rules. Changesor
modifications not
exp re ss ly app roved by the party responsible for compli an ce co uld vo id the u se r's
author
it y to op erate the d ev ice.
The term "IC:" before the certifi
ca tion/registration nu mb er only signifi es thatIndustryCanada
technical speci
fi cat ions were met.
IC: 270B-xxxxx JCI MODEUFCC 1
0: CB2XXXXX
Home
li nk "' and the Ho me li nk hou se are registered trademarks ow ned by
Jo hnson Co ntrols, Inc.
JCI-13356 5/02