Johnson Controls VMA1930 User manual

VMA1930 VAV Controller Installation Guide
Application
The VMA1930 equipment controllers are designed
for Variable Air Volume (VAV) applications that
communicate over BACnet®/IP networks. These
Variable Air Volume Modular Assembly (VMA)
controllers feature combinations of an integral
digital pressure sensor (DPT), a damper actuator,
and a 32-bit microprocessor. The controllers' small
package size facilitates quick field installation and
efficient use of space without compromising high-
tech control performance. The VMA1930 controllers
include an integral real-time clock, which enables
the controllers to monitor and control schedules,
calendars, and trends, and operate for extended
periods of time as stand-alone controllers when
offline from the Metasys® system network. These
VMA controllers connect easily to the wired and
wireless network sensors for zone and discharge air
temperature sensing.
The Metasys system Field Equipment Controllers
(FEC) family controllers and network sensors
communicate using the BACnet protocol. The
BACnet protocol is a standard for ANSI, ASHRAE,
and the International Standards Organization (ISO)
for building controls. VMA1930 Field Controllers
are BACnet Testing Laboratories (BTL) listed and
certified BACnet Advanced Application Controllers
(B-AACs).
North American emissions
compliance
United States
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when this equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area
may cause harmful interference, in which case the
users will be required to correct the interference at
their own expense.
Canada
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Installation
Observe the following guidelines when installing a
VMA1930 controller:
• Transport the controller in the original container
to minimize vibration and shock damage to the
controller.
• Do not drop the controller or subject it to physical
shock.
Parts included
• One VMA1930 controller with removable SA bus
and power terminal blocks
• One installation instructions sheet
• One self-drilling No. 10 x 25 mm (1 in.) screw
Materials and special tools needed
• Several 6 mm (1/4 in.) female spade terminals for
input and output wiring, and crimping tool for
spade mounted terminal blocks
• Small, straight-blade screwdriver for securing
wires in the terminal blocks, can also be used to
adjust controller numbers
• 8 mm (5/16 in.) wrench or 10 mm (3/8 in.) 12-point
socket to tighten the square coupler bolt
• Several shims or washers to mount the VMA
• Power screwdriver, 100 mm (4 in.) extension
socket, punch, drill, and 3.5 mm (9/64 in.) drill bits
to mount the VMA
• Pliers to open and close the damper
*2410143853C*
Part No. 24-10143-853 Rev. C
2019-11-21
(barcode for factory use only)
MS-VMA1930-0

• Required length of 3.97 mm (5/32 in.) ID
pneumatic tubing and barbed fittings VMA1930 physical features
The following figure displays the physical features
of the VMA1930, and the accompanying table
provides a description of the physical features and a
reference to further information where required.
Figure 1: VMA1930 Controller wiring terminations and physical features
Table 1: VMA1930 Feature Callout Numbers and
Descriptions
Callout Physical Features: Description and References
124 VAC, Class 2 Supply Power (see Supply power
terminal block)
2Controller Number Rotary Switches (see Setting the
controller number): can be numbered from 000 to 999
3 Binary Outputs, 24 VAC Triacs (see Table 3)
4Configurable Outputs: Voltage Analog Output (0–10
VDC) and Binary Output (24 VAC Triac) (see Table 3)
5 Dual Port Fitting
6Manual Override Button (see Mounting for information
about using manual override Button)
7Controller Coupler (see Mounting for information about
using the controller coupler )
8Coupler Bolt (see Mounting for information about
setting the coupler bolt )
Table 1: VMA1930 Feature Callout Numbers and
Descriptions
Callout Physical Features: Description and References
9
Universal Input: Voltage Analog Input (0–10 VDC)
Resistive Analog Inputs (0–600k ohm) (see Table 3):
0–2k Potentiometer
RTD: 1k Nickel, 1k Platinum, or A99B SI
NTC: 10K Type L (10K Johnson Controls Type II is
equivalent to Type L) or 2.252K Type II
Dry Contact Binary Input
10 SA Bus Terminal Block (see SA Bus terminal block)
11 Sensor Port (SA Bus) RJ-12 6-Pin Modular Jack (see SA
Bus port)
12 ETH2 Ethernet Port for BACnet/IP Communications
13 ETH1 Ethernet Port for BACnet/IP Communications
14 Captive Spacer and Screw
15 LED Status Indicators (see Table 7)
VMA1930 VAV Controller Installation Guide2

VMA1930 model information
Table 2: VMA1930 information (including point type counts per model)
Communication Protocol BACnet/IP
Engines Supported NAE55, NAE85, ODS
Modular Jacks 6-pin SA Bus with four communicating
sensors
Point Types Signals Accepted Number of Points
Universal Input (UI)
Analog Input, Voltage Mode, 0–10 VDC
Analog Input, Current Mode, 4-20mA
Analog Input, Resistive Mode, 0–2k ohm, RTD (1k
NI [Johnson Controls], 1k PT, A998 SI), NTC (10k
Type L, 2.252k Type 2)
Binary Input, Dry Contact Maintained Mode
3
Binary Output (BO) 24 VAC Triac 3
Configurable Output (CO) Analog Output, Voltage Mode, 0–10 VDC
Binary Output Mode, 24 VAC Triac 2
Integrated Actuator Internal 1
Differential Pressure Transducer (DPT) Internal 1
Up to 4 NS Series Network Zone Sensors
Zone Sensor Input On SA Bus Up to 5 WRZ sensors when using the one-to-
one WRZ-78xx wireless configuration
VMA1930 VAV Controller Installation Guide 3

Mounting
Observe the following guidelines when mounting a
VMA:
Note: When the air supply to the VAV box
is below 10°C (50°F), make sure that any
condensation on the VAV box, particularly on
the damper shaft, does not enter the VMA
• Ensure that the mounting surface can support
the controller and any user-supplied enclosure.
electronics. Mount the controller vertically above
the damper shaft to allow any shaft condensation
to fall away from the controller. Additional
measures may be required in some installations.
• Mount the controller on a hard, even surface
whenever possible.
• Use shims or washers to mount the controller
securely and evenly on the mounting surface.
• Mount the controller in an area free of corrosive
vapors that matches the ambient conditions
specified in the Technical specifications section.
• Provide sufficient space around the controller
for cable and wire connections and adequate
ventilation through the controller (at least 50 mm
[2 in.] on the top, bottom, sides, and front of the
controllers).
• Mount the VMA vertically above the damper shaft
to allow any shaft condensation to fall away from
the VMA.
Do not mount the controller in areas where
electromagnetic emissions from other
devices or wiring can interfere with controller
communication.
• Avoid mounting the controller on surfaces with
excessive vibration.
On panel or enclosure mount applications, observe
these additional guidelines:
• Do not install the controller in an airtight
enclosure.
• Mount the controller so that the enclosure walls
do not obstruct cover removal or ventilation
through the controller.
• Mount the controller so that the power
transformer and other devices do not radiate
excessive heat to the controller.
To mount the controllers, complete the following
steps:
1. Set all the switches on the field controller to
their known settings.
2. Place the controller in the proper mounting
position on the damper shaft so that the wiring
connections are easily accessible. Make sure
the controller base is parallel to the VAV box
(perpendicular to the damper shaft). If needed,
use a spacer to offset tipping of the controller
caused by the shaft bushings.
Note: Use the alignment marks to center
the captive spacer to ensure sufficient
movement in either direction.
3. Secure the self-drilling No. 10 screw through
the captive spacer with a power screwdriver
and 100 mm (4 in.) extension socket. Otherwise,
use a punch to mark the position of the
shoulder washer, and then drill a hole into the
VAV box using a 3.5 mm (9/64 in.) drill bit. Insert
the mounting screw and tighten against the
spacer.
Important: Do not overtighten the screw,
or the threads may strip. If mounting to
the VAV box, make sure the screws do not
interfere with damper blade movement.
4. Locate the damper position using the typical
marking on the end of the damper shaft as
shown in the following figure.
Figure 2: Typical Damper End Shaft Icons
5. Note the direction, clockwise (CW) or
counterclockwise (CCW), required to close the
damper. Grasp the damper shaft firmly with
pliers, and either manually close the damper for
90° boxes or manually open the damper for 45°
or 60° boxes.
VMA1930 VAV Controller Installation Guide4

6. Push down and hold the Manual Override
button (see VMA1930 physical features) and
turn the controller coupler until it contacts the
mechanical end-stop at either the full-closed
(90° boxes) or full-open (45° and 60° boxes)
position.
7. If the damper for a 90° box closes CCW, rotate
the coupler to the CCW mechanical limit. If
the damper for a 90° box closes CW, rotate
the coupler to the CW mechanical limit. The
open end-stop is automatically set for 90°
boxes. For 45° and 60° boxes, hard stops must
be provided at both full-closed and full-open
damper positions. By installing the controller at
the full-open position, the controller provides
the open stop for 45° and 60° boxes. The closed
damper seal provides the full-closed stop.
Note: The integrated actuator has a
stroke time of 60 seconds for 90° of travel.
The stroke time is the amount of time
(in seconds) that it takes the actuator
to move from the fully closed to fully
opened position or from fully open to fully
closed position. For proper operation, the
actuator stroke time must be configured
in the CCT application based on the actual
time it takes the actuator to drive the
damper. The default setting is 60 seconds
(for 90° VAV boxes). For 45° and 60° VAV
boxes, the actuator stroke time must be
adjusted. Refer to Controller Tool Help
(LIT-12011147) for instructions on setting
the actuator stroke time in the application.
8. All models are compact in size and can be
easily installed on VAV boxes. The models have
either a round shaft up to 13 mm in diameter
or a 10 mm square shaft. Tighten the square
coupler bolt to the shaft using an 8 mm (5/16
in.) wrench or 10 mm (3/8 in.) 12-point socket.
Tighten to 10.5 to 11.5 N·m (95 to 105 lb·in).
9. (Skip this step if you are installing the
VMA1626 model) Loop the pneumatic tubing
(supplied by field personnel) to include a
trap for condensation. Attach the needed
length of tubing (supplied and installed by
field personnel) to the dual port fitting on the
controller and the other ends of the tubing
to the pressure transducer in the VAV box
application.
Note: The controller uses a digital non-
flow pressure sensor with bidirectional
flow operation. You can connect the high-
and low-pressure DP tubes to either
barbed fitting on the controller. You do not
need to make a specific high- or low-side
connection when you attach the tubing to
the barbed fittings on the controller.
10. Push the Manual Override button, and turn the
actuator coupling manually to ensure that the
actuator can rotate from full-closed to full-open
positions without binding.
11. Complete the mounting by rotating the damper
to the full-open position.
CAUTION
Risk of Property Damage
Rotate the damper to the full-open position before
starting the air handler. Failure to rotate the damper to
the full-open position may result in damage to the VAV
box or ductwork when the air handler is started.
ATTENTION
Risque de dégâts matériels
Faire pivoter le registre pour le placer en position
d'ouverture complète avant de démarrer l'unité de
traitement d'air. Le non-respect de cette directive
risque d'endommager le caisson de l'unité à volume
d'air variable (VAV) ou le réseau de conduites au dé-
marrage de l'unité de traitement d'air.
Wiring
CAUTION
Risk of Electric Shock
Disconnect the power supply before making electrical
connections to avoid electric shock.
VMA1930 VAV Controller Installation Guide 5

ATTENTION
Risque de décharge électrique
Débrancher l'alimentation avant de réaliser tout rac-
cordement électrique afin d'éviter tout risque de
décharge électrique.
Important: Do not connect supply power
to the controller before finishing wiring and
checking all wiring connections. Short circuits
or improperly connected wires can result
in damage to the controller and void any
warranty.
Important: Do not exceed the controller
electrical ratings. Exceeding controller electrical
ratings can result in permanent damage to the
controller and void any warranty.
Important: Use copper conductors only. Make
all wiring in accordance with local, national, and
regional regulations.
Important: Electrostatic discharge can
damage controller components. Use proper
electrostatic discharge precautions during
installation, setup, and servicing to avoid
damaging the controller.
For information on configuring and wiring
a BACnet/IP network, refer to the Metasys IP
Networks for BACnet/IP Controllers Configuration
Guide (LIT-12012458). For detailed information on
configuring and wiring a SA Bus, refer to the MS/TP
Communications Bus Technical Bulletin (LIT-12011034).
Network topology
VMA1930 controllers may be connected to a building
automation network in multiple ways: as daisy-
chained devices, as part of a star (also called home
run) type network, or as part of a ring network.
To daisy-chain VMA1930 controllers, connect the
controllers to the bus supervisor in a chain with
the Ethernet cable connecting to the VMA1930
at the ETH1 or ETH2 port, and connecting to the
next device from the other port. Benefits of daisy-
chained networks are that they require less physical
wiring and new devices can be added easily to the
network.
In a star network, each VMA1930 controller is
connected by Ethernet cable directly back to a main
switch. This configuration reduces the possibility of
network failure but requires more wiring to install.
A ring network is a chain of controllers virtually
closed by a software component in an Ethernet
switch. Not all switches support the ring topology.
The dual-port controller from Johnson Controls
supports Media Redundancy Protocol (MRP). With
MRP, a chain of Ethernet devices can overcome any
single communication failure, with a recovery time
faster than in a BACnet system.
For more information about network topologies for
Metasys BACnet/IP Controllers, refer to the Metasys
IP Networks for BACnet/IP Controllers Configuration
Technical Bulletin (LIT-12012458).
VMA terminals and bus ports
See VMA1930 physical features for input and output
terminal and bus port locations on the controllers.
Observe the following guidelines when wiring a
VMA controller.
Input and Output terminals
The input spade terminals are located on the
bottom of the VMA near the FC Bus terminal block.
The output spade terminals are located on the top
of the controller near the power supply terminal
block. For more information, see Table 3.
SA Bus terminal block
The SA Bus terminal block is a brown, removable,
4-terminal plug with +15 VDC that fits into a board-
mounted jack. Wire the removable SA Bus terminal
block plugs on the VMA and other SA Bus devices
in a daisy-chain configuration using 4-wire twisted,
shielded cable as shown in Figure 3. See Table 5 for
more information.
Figure 3: SA bus terminal block wiring
VMA1930 VAV Controller Installation Guide6

SA Bus port
The Sensor (SA Bus) port on the bottom of the
controller is an RJ-12, 6-position modular jack that
provides a connection for the Mobile Access Portal
(MAP) Gateway, the Bluetooth Commissioning
Converter (BTCVT), the VAV Balancing Tool, specified
network sensors, or other SA Bus devices with RJ-12
plugs. A DIS1710 Local Controller Display can also be
connected to the SA Bus port.
Note:
• Do not use the modular SA Bus port and the
terminal block SA Bus simultaneously. Only
use one of these connections at a time.
• The MAP Gateway serves as a replacement
for the BTCVT, which is no longer available
for purchase, but continues to be supported.
The Sensor port is connected internally to the SA
bus terminal block. For more information about
Sensor port functions, requirements, and ratings,
see Table 5.
Figure 4: Pin number assignments for Sensor
(SA Bus) Port on VMA1930
Supply power terminal block
The 24 VAC supply power terminal block is a
gray, removable, 2-terminal plug that fits into a
board-mounted jack on the upper left of the VMA
controller.
Wire the 24 VAC supply power wires from the
transformer to the HOT and COM terminals on the
terminal plug as shown in the following figure. See
Table 5 for more information.
Figure 5: 24 VAC supply power terminal block
wiring
The supply power wire colors may be different on
transformers from other manufacturers. Refer to
the transformer manufacturer’s instructions and
the project installation drawings for wiring details.
Important: Connect 24 VAC supply power to
the controller and all other network devices
so that transformer phasing is uniform across
the network devices. Powering network
devices with uniform 24 VAC supply power
phasing reduces noise, interference, and
ground loop problems. The controller does not
require an earth ground connection. However,
when grounding the secondary of the 24 VAC
transformer is required, only one connection to
ground should be made near the transformer.
See the following figure.
Figure 6: Transformer Grounding
VMA1930 VAV Controller Installation Guide 7

CAUTION
Risk of Property Damage
Do not apply power to the system before checking all
wiring connections. Improper wiring of this terminal
may cause a short circuit across the 24 VAC power
supply on VMA models. A short circuit may result in a
tripped circuit breaker or blown fuse. If using a trans-
former with a built-in fuse, the transformer may need
to be replaced.
ATTENTION
Risque de dommages matériels
Ne mettez pas l’appareil sous tension avant d’avoir
vérifié toutes les connexions du câblage. Le câblage
inadéquat de cette borne peut causer un court-cir-
cuit sur l’alimentation électrique de 24 V c.a. des VMA
modèles. Un court-circuit peut causer le déclenche-
ment du disjoncteur ou le grillage d’un fusible. Si vous
utilisez un transformateur avec un fusible intégré,
vous pourriez devoir remplacer le transformateur.
To wire the controller, complete the following steps:
1. Terminate wiring according the appropriate
figure in Termination diagrams.
2. Wire network sensors and other devices to the
VMA's SA Bus.
3. Wire the FC Bus in a daisy chain.
4. Ensure that the device address DIP switches
are set to the appropriate device address (See
Setting the controller number). Also, activate
the EOL switch if necessary.
5. Connect the controller to 24 VAC, Class 2 power.
Note: If you are using the
VMA1615/1626/1628/1630 controller with
the Wireless Field Bus System, refer to the
WNC1800/ZFR182x Pro Series Wireless Field Bus
System Bulletin (LIT-12012320) or the ZFR Series
Wireless Field Bus System Bulletin (LIT-12011336).
Terminal wiring guidelines,
functions, ratings, and
requirements
Input and Output wiring guidelines
See Table 3 for information about the functions,
ratings, and requirements for the input and output
terminals, and for wire sizes and cable lengths
guidelines.
In addition, observe the following guidelines when
wiring inputs and outputs:
• Run all low-voltage wiring and cables separate
from high-voltage wiring.
• All input and output cables, regardless of wire
size or number of wires, should consist of twisted,
insulated, and stranded copper wires.
• Shielded cable is not required for input or output
cables but is recommended for input and output
cables that are exposed to high electromagnetic
or radio frequency noise.
• Cable runs of less than 30 m (100 ft) typically do
not require an offset in the input/output software
setup.
• Cable runs over 30 m (100 ft) may require an
offset in the input/output software setup.
VMA1930 VAV Controller Installation Guide8

I/O terminal blocks, ratings and requirements
Table 3: I/O terminal blocks, functions, ratings, requirements, and cables
Terminal block label Terminal labels Function, ratings, and requirements To determine wire size and
maximum cable length
+15 V
15 VDC Power Source for active (3-wire) input
devices connected to the Universal INn terminals.
Provides 35 mA total current.
Same as (Universal) INn.
Note: Use 3-wire cable for
devices that source power
from the +15 V terminal.
Analog Input - Voltage Mode (0–10 VDC)
10 VDC maximum input voltage
Internal 75k ohm Pulldown
See Guideline A in Table 4.
Analog Input - Resistive Mode (0–600k ohm)
Internal 12 V, 15k ohm pull up
Qualified Sensors: 0–2k potentiometer,
RTD (1k Nickel [Johnson Controls sensor],
1k Platinum, and A99B Silicon Temperature Sensor)
Negative Temperature Coefficient (NTC) Sensor
10K Type L (10K Johnson Controls Type II is
equivalent to Type L) or 2.252K Type II
See Guideline A in Table 4.INn
Binary Input - Dry Contact Maintained Mode
1 second minimum pulse width
Internal 12 V, 15k ohm pull up
See Guideline A in Table 4.
UNIVERSAL
(Inputs)
ICOMn
Universal Input Common for all Universal IN
terminals
Note: All Universal ICOMn terminals are
isolated from all other commons.
Same as (Universal) INn.
OUTnBinary Output - 24 VAC Triac (Internal Power)
Sources internal 24 VAC power (24~ HOT) See Guideline C in Table 4.
BINARY
(Outputs) OCOMn
Binary Output - 24 VAC Triac (Internal Power)
Connects OCOMn to 24~ COM when activated.
Internal Power Source:
30 VAC maximum voltage to load
0.5 A maximum output current
1.3 A at 25% duty cycle
40 mA minimum load current
See Guideline C in Table 4.
VMA1930 VAV Controller Installation Guide 9

Table 3: I/O terminal blocks, functions, ratings, requirements, and cables
Terminal block label Terminal labels Function, ratings, and requirements To determine wire size and
maximum cable length
Analog Output - Voltage Mode (0–10 VDC)
10 VDC maximum output voltage
10 mA maximum output current
External 1k to 50k ohm load required
See Guideline A in Table 4.
OUTn
Binary Output 24 VAC Triac
Connects OUT to OCOM when activated.
External Power Source:
30 VAC maximum voltage to load
0.5 A maximum output current
1.3 A at 25% duty cycle
40 mA minimum load current
See Guideline C in Table 4.
Analog Output Signal Common: All Configurable
Outputs defined as Analog Outputs share a
common, which is isolated from all other commons
except the Binary Input common.
CONFIGURABLE
(Outputs)
OCOMnBinary Output Signal Common: All Configurable
Outputs defined as Binary Outputs are isolated
from all other commons, including other
Configurable Output commons.
Same as (Configurable) OUTn.
Cable and wire length guidelines
The following table defines cable length guidelines
for the various wire sizes that may be used for
wiring low voltage (<30 V) input and outputs.
Table 4: Cable length guidelines
Guideline Wire size/Gauge and type Maximum cable length and
type Assumptions
1.0 mm (18 AWG) stranded copper 457 m (1,500 ft) twisted wire
0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire 297 m (975 ft) twisted wire
0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire 183 m (600 ft) twisted wire
A
0.5mm (24 AWG) stranded copper
107 m (350 ft) twisted wire 107 m (350 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
1.0 mm (18 AWG) stranded copper 229 m (750 ft) twisted wire
0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire 137 m (450 ft) twisted wire
0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire 91 m (300 ft) twisted wire
B
0.5mm (24 AWG) stranded copper
107 m (350 ft) twisted wire 61 m (200 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
C
See Maximum cable length versus
load current to select wire size/
gauge.
Use stranded copper wire.
See Maximum cable length
versus load current to determine
cable length.
Use twisted wire cable.
N/A
VMA1930 VAV Controller Installation Guide10

Maximum cable length versus load
current
Use Figure 7 to estimate the maximum cable length
relative to the wire size and the load current (in mA)
when wiring inputs and outputs.
Figure 7: Maximum Wire Length by Current and
Wire Size
Communications bus and supply
power wiring guidelines
provides information about terminal block
functions, ratings, and requirements..
In addition, observe these guidelines when wiring
the SA Buses and supply power:
• Run all low-voltage wiring and cables separate
from high-voltage wiring.
• All SA Bus cables, regardless of wire size, should
be twisted, insulated, stranded copper wire.
• Shielded cable is strongly recommended for all SA
Bus cables.
• Refer to the MS/TP Communications Bus
Technical Bulletin (LIT-12011034) for detailed
information regarding wire size and cable length
requirements for SA Buses.
Communication bus and supply power terminal blocks, ratings, and requirements
Table 5: Communication bus and supply power terminal blocks, functions, ratings, requirements, and
cables
Terminal block/Port label Terminal labels Function, electrical ratings/
Requirements Recommended cable type11
+
-SA Bus Communications
COM SA Bus Signal Reference and 15 VDC
Common
SA BUS22
POWER 15 VDC Supply Power for Devices on the
SA Bus
0.6 mm (22 AWG) stranded, 4-wire
(2 twisted-pairs), shielded cable
recommended
Note: The + and - wires are one
twisted pair, and the COM and
SA PWR wires are the second
twisted pair.
SENSOR SENSOR
RJ-12 6-Position Modular Port provides
SA Bus Communications
SA Bus provides 15 VDC Power for:
NS Series Sensors
MAP Gateway 4.2 or above
Bluetooth Commissioning Converter
(BTCVT)33
DIS1710 Local Controller Display
VAV Balancing Tool
24 AWG 3-pair CAT 3 Cable <30.5 m
(100 ft)
ETH1 and ETH2 ETH1 and ETH2 Connect to BACnet/IP Network Ethernet ports; 10/100 Mbps; 8-pin
RJ-45 connector
HOT 24 VAC Power Supply - Hot
Supplies 20–30 VAC (Nominal 24 VAC)
24~
COM
24 VAC Power Supply Common
The terminal is isolated from the FC bus
common.
0.8 mm to 1.0 mm
(20 to 18 AWG) 2-wire
1 To determine wire size and cable lengths for cables other than the recommended cables, see Table 4.
2 The SA bus wiring recommendations are for MS/TP Bus communications at 38.4k baud. For more information, refer to the MS/TP
Communications BusTechnical Bulletin (LIT-12011034).
3 The MAP Gateway serves as a replacement for the BTCVT, which is no longer available for purchase, but continues to be supported.
VMA1930 VAV Controller Installation Guide 11

Termination diagrams
A set of Johnson Controls termination diagrams provides details for wiring inputs and outputs to the
controllers. See the figures in this section for the applicable termination diagrams.
Table 6: Termination details
Type of field device Type of Input/
Output Termination diagrams
Voltage Input -
External Source UI
Voltage Input -
Internal Source UI
Voltage Input (Self-
Powered) UI
Temperature Sensor UI
Dry Contact UI
VMA1930 VAV Controller Installation Guide12

Table 6: Termination details
Type of field device Type of Input/
Output Termination diagrams
0–10 VDC Output to
Actuator (Internal
Source)
CO
0–10 VDC Output to
Actuator (External
Source)
CO
24 VAC Triac Output
(Switch Low, External
Source)
CO
Note: Applies to CO4 and CO5.
Incremental Control to
Actuator (Switch Low,
External Source)
CO
Note: Applies to CO4 and CO5.
Analog Output
(Voltage) CO
Incremental Control to
Actuator (Switch Low,
Internally Sourced)
BO
Note: Applies to BO3, BO1, and BO2.
VMA1930 VAV Controller Installation Guide 13

Table 6: Termination details
Type of field device Type of Input/
Output Termination diagrams
24 VAC Binary Output
(Switch Low, Internally
Sourced)
BO
Network Stat with
Phone Jack (Fixed
Address = 199)
SA Bus
Network Stat with
Terminals Addressable SA Bus
Network Stat with
Terminals (Fixed
Address = 199)
SA Bus
Setup and adjustments
Important: Electrostatic discharge can
damage controller components. Use proper
electrostatic discharge precautions during
installation, setup, and servicing to avoid
damaging the controller.
Setting the controller number
Each controller on a network must have a unique
number on the subnet where it resides in order
to identify it in the Controller Tool for uploading,
downloading, and commissioning.
The controller number is set using three rotary
switches and may be numbered from 000 to 999.
The numbers are ordered from left to right, most
significant bit (MSB) to least significant bit (LSB).
In the following figure the switches are set to
4 2 5, designating this controller as controller
number 425. The controller number must match
the controller number defined in Controller
Configuration Tool (CCT) under Define Hardware
VMA1930 VAV Controller Installation Guide14

> Network Settings. The number of the controller
can be written in the white squares provided so the
controller number can be more easily seen from a
distance.
Figure 8: Rotary switch for setting controller
numbers
Note: The BACnet device ID is calculated
using the value of controller number added to
2000000. A device ID configured in this manner
does not require any configuration from CCT.
Input/Output Wiring Validation
The VMA1930 controllers ship with a default state
that can assist in validating the wiring of the input
and output terminals prior to download of an
application file. When the controller is powered on
in this state, the Fault LED will flash in a pattern of
two quick blinks and then a long pause (see Table
7).
To make use of this feature, ensure the rotary
switches are set to the desired controller number
and wire the input and output terminals. Apply
power to the VMA1930 controller and connect to the
device with either a MAP Gateway or MS-DIS1710-0
Local Display to view the points in the controller.
The VMA1930 controller will report an Operational
status even though there is no true application
loaded. CCT will not be able to commission or
upload the device as a result until a true application
is downloaded. The application name displayed will
be the controller number followed by the model of
the controller and “Default State”.
For example, a VMA1930 controller whose rotary
switches are set to 8 would have the default state
application name of 8-VMA1930 Default State.
The default state creates I/O points for all
connections on the input and output terminals,
including the integrated DPT. It assumes all
Universal Inputs (UIs) are Nickel temperature
sensors. All Configurable Outputs (COs) are treated
as Binary Outputs (BOs) with an initial value of
0. The actuator on the VMA1930 will drive to the
50% setting. The default state also takes input
from a Network Sensor at address 199. If there is
no connected Network Sensor, the startup of this
default state will be delayed by 30 seconds as the
controller attempts to establish connection with the
sensor.
Commissioning Field Controllers
To commission the VMA1930 controller, use the
following procedure:
1. Download the control application to the
controller using the Controller Configuration
Tool (CCT). Refer to the Controller Tool Help
(LIT-12011147) and Controller Provisioning with
Tools (LIT-12013247) .
2. Commission the VAV Box.
3. Perform airflow balancing on the VAV box.
Refer to the VAV Balancing Tool Technical Bulletin
(LIT-12011087).
4. Perform commissioning checkout procedures.
Refer to the Controller Tool Help (LIT-12011147)
and Controller Provisioning with Tools
(LIT-12013247).
You commission controllers with the CCT software.
The controller can be connected in one of four
ways; either through NxE Passthru, MAP 4.2+/
BACnet Router (Mobile Access Portal (MAP)
Gateway at version 4.2 or above), through Bluetooth
(using BTCVT), or Direct Ethernet connection to
the controller. Refer to the Controller Tool Help
(LIT-12011147) and Controller Provisioning with
Tools (LIT-12013247) for detailed information about
commissioning field controllers.
Note:
• The Bluetooth connection can be used
to Transfer to Computer (Upload) and
commission the controller, but cannot be
used to Transfer to Device (Download).
VMA1930 VAV Controller Installation Guide 15

• The MAP Gateway serves as a replacement
for the BTCVT, which is no longer available
for purchase, but continues to be supported.
Firmware Package File
The MS-FCP-0 equipment controller firmware
package files are required for CCT to configure and
commission the controllers. The firmware package
files also allow you to upgrade an existing controller
to the latest firmware release available for that
controller.
Beginning at CCT Release 13, the firmware package
files are orderable separately; they are not included
with CCT. They are obtained from the Metasys
software licensing portal, and are loaded and
licensed on the computer/server that is running
CCT.
For additional information about the firmware
package files, refer to the CCT Installation Instructions
(LIT-12011259).
Troubleshooting Field Controllers
Observe the Status LEDs on the front of the
expansion module. Table 7 provides LED status
indicator information for troubleshooting the
expansion module.
General troubleshooting provides some additional
troubleshooting information for possible problems.
Note: If you experience short circuits in the 24
VAC power supply causing protective devices
such as breakers or fuses to trip, make sure
that the power connections on theVMA1930 are
not reversed. The most common cause of this
problem is when the 24 VAC power supply on
the VMA1930 is reversed but not reversed on a
connected secondary device. Improper wiring
of this power terminal may cause a short circuit
across the 24 VAC power supply.
LED status and states
Table 7: Status LEDs and description of LED states
LED label LED color Normal state Descriptions of LED states
POWER Green On Steady Off Steady = No power
On Steady = Power is supplied by primary voltage
FAULT Red Off Steady
2 blinks followed by long pause = Controller powered
on in default state. For more information about this
default state, see Input/Output Wiring Validation.
Blink - 2 Hz = Download or startup in progress, not
ready for normal operation, SA Bus devices offline
(such as netsensors)
Rapid blink = SA Bus communications issue
Off Steady = No faults
On Steady = Device fault or no application loaded
SA BUS Green Blink - 2 Hz
Blink - 2 Hz = Data transmission (normal
communication)
Off Steady = No data transmission (N/A - auto baud
not supported)
On Steady = Communication lost; waiting to join
communication ring
ETH1 Green Off Off Steady = ETH1 is not connected
Blinking = ETH1 connected and communicating
ETH2 Green Off Off Steady = ETH2 is not connected
Blinking = ETH2 connected and communicating
VMA1930 VAV Controller Installation Guide16

General troubleshooting
Table 8: Troubleshooting
Problem Possible cause and correction Verification
Controller is OFF.
Transformer has tripped:
Power is at Primary of Transformer, 0V at
Secondary.
Breaker/Fuse has tripped:
Power is at Primary of Transformer, 24V at
Secondary, 0V at Fuse/Breaker.
Cause:
1. Transformer is shorted.
2. 24 VAC powered sensor is not
wired with the same polarity as the
controller.
3. SA Bus device is not wired with the
same polarity as the controller.
Correction:
1. Ensure polarity of ~24 V COM / ICOM /
+ 15VCOM/SA BUS COM on the
controller, auxiliary devices, and I/O is
the same.
2. Ensure OUT1-OUT3 terminals of binary
outputs are not connected to ~24
VAC COM, and verify that OCOM1-
OCOM3 are not connected to ~24 VAC
HOT (these terminals are internally
sourced).
3. Verify the short circuit has been
resolved with an ohm-meter.
4. Reset the breaker/fuse or replace the
transformer.
Note: When replacing the
transformer, it is recommended to
replace with a model that utilizes a
resettable circuit breaker. A circuit
breaker makes solving wiring
problems easier.
1. Disconnect the Secondary of the 24
VAC transformer.
2. Use an ohm-meter to measure
between ~24 V HOT and COM; there
must be no short circuit.
Note: Some installations require
the Secondary of the Transformer
to be Earth Grounded. If this is
the case, verify that the Earth
Ground connection is valid and not
shared between multiple pieces of
equipment.
Configurable output - analog mode is
invalid:
0–10 V output is set to 10–100%, but 0 V is at
output terminals.
Output is in protection mode, a state the
analog portion of the configurable output
goes into when it detects a wiring problem.
The analog output is set to 0% regardless
of the command whenever a wiring fault is
detected.
Cause:
There is a power polarity mismatch between
the connected device and the configurable
output.
Correction:
Ensure polarities of ~24 V COM/OCOM
match and that the connected end device
uses the same polarity.
1. Measure the output and verify that it
matches the command.
2. Disconnect the connected device
and verify the commanded value is
present.
Configurable output - analog mode is
invalid:
0–10V output has an undesirable offset of up
to 1 V.
The Common Reference is incorrect.
Cause:
The OCOM terminal is not connected.
Correction:
Connect the OCOM terminal of the
configurable output to the common of the
connected end device.
1. Measure the output and verify that it
matches the command.
2. Disconnect the connected device
and verify the commanded value is
present.
Repair information
If the controller fails to operate within its specifications, replace the unit. For a replacement unit, contact the
nearest Johnson Controls representative.
VMA1930 VAV Controller Installation Guide 17

Accessories
Table 9: Controller accessories (order separately)
Product code number Description
IOM Series Controllers Refer to the Metasys® System Field Equipment Controllers and Related Products Product Bulletin
(LIT-12011042) for a complete list of available IOM Series Controllers.
NS Series Sensors Refer to the NS Series Network Sensors Product Bulletin (LIT-12011574) for a complete list of
available NS Series Sensors.
Mobile Access Portal (MAP) Gateway
Refer to the Mobile Access Portal Gateway Catalog Page (LIT-1900869) to identify the
appropriate product for your region.
Note: The MAP Gateway serves as a replacement for the BTCVT, which is no longer
available for purchase, but continues to be supported.
TL-CCT-0 Metasys Controller Configuration Tool
MS-FCP-0 Metasys Equipment Controller Firmware Package Files for CCT
WRZ Series Sensors Refer to the WRZ Series Wireless Room Sensors Product Bulletin (LIT-12011653) for a complete
list of available WRZ Series Sensors.
MS-DIS1710-0 Local Controller Display
Y64T15-0 Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 92 VA, Foot Mount, 72.2 cm (30
in.), Primary Leads and 76.2 cm (30 in.) Secondary Leads, Class 2
Y65A13-0 Transformer, 120 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount (Y65AS), 20.32 cm (8
in.), Primary Leads and 76.2 cm (30 in.) Secondary Leads, Class 2
Y65T42-0 Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Hub Mount (Y65SP+),
20.32 cm (8 in.), Primary Leads and Secondary Screw Terminals, Class 2
Y65T31-0 Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount (Y65AR+),
20.32 cm (8 in.), Primary Leads and Secondary Screw Terminals, Class 2
AP-TBK1002-0 2-position Screw Terminal that plugs onto VMA Output Point Spade Lugs
AP-TBK1003-0 3-position Screw Terminal that plugs onto VMA Output Point Spade Lugs
AP-TBK4SA-0 Replacement MS/TP SA Bus Terminal, 4-Position Connector, Brown, Bulk Pack of 10
AP-TBK2PW-0 Replacement Power Terminal, 2-Position Connector, Gray, Bulk Pack of 10
MS-VMAACT-701 VMA Actuator Assembly Gearbox Replacement Kit
AS-CBLTSTAT-0 Cable adapter for connection to 8-pin TE-6700 Series sensors
F-1000-325 Replacement Barbed Fitting for use on VMA1930 for Connecting Tubing, Bulk Pack of 10
F-1000-326 Flexible Tubing Extension with Barbed Fitting for VMA1930, 35.56 cm (14 in.) Length, Bulk
Pack of 20
TL-BRTRP-0 Portable BACnet/IP to MS/TP Router
VMA1930 VAV Controller Installation Guide18

Technical specifications
Table 10: VMA1930 Controllers
Product Code Numbers
MS-VMA1930-0: 32-bit, Integrated VAV Controller/Actuator/Pressure Sensor - DPT, 3 UI
and 3 BO, 2 CO, 24 VAC, and SA Bus, Includes 6-pin Sensor Port for use with TE-7xx Series
Non-Communicating Sensors and two Ethernet Ports for BACnet/IP Communications
Communications Protocol BACnet/IP
Engines Supported NAE55, NAE85, ODS
Power Requirement 24 VAC (nominal, 20 VAC minimum/30 VAC maximum), 50/60 Hz, Power Supply Class 2
(North America), Safety Extra-Low Voltage (SELV) (Europe)
Power Consumption
10 VA typical, 14 VA maximum
Note: The VA rating does not include any power supplied to the peripheral devices
connected to Binary Outputs (BOs) or Configurable Outputs (COs), which can
consume up to 12 VA for each BO or CO, for a possible total consumption of an
additional 60 VA (maximum).
Power Source +15 VDC power source terminals provide 35 mA total current. Quantity 1 located in
Universal IN terminals - for active (3-wire) input devices
Ambient Conditions Operating: 0°C to 50°C (32°F to 122°F)
Storage: -40°C to 70°C (-40°F to 158°F)
Terminations
Inputs/Outputs 6.3 mm (1/4 in.) Spade Lugs
SA Bus, and Supply Power: 4-Wire and 2-Wire Pluggable Screw Terminal Blocks
SA Bus Modular Ports: RJ-12 6-Pin Modular Jacks
Controller Number Set of 3 Rotary switches used to set controller number between 001 and 999.
Communications Bus
Two Ethernet ports; 10/100 Mbps; 8-pin RJ-45 connector
SA Bus: 0.6 mm (22 AWG) stranded, 4-wire (2-twisted pairs) shielded cable recommended
from the VMA controller for network sensors and other sensor/actuator devices; includes
a terminal to source 15 VDC supply power from the VMA1930 to SA Bus devices
Note: For more information, refer to the MS/TP Communications Bus Technical
Bulletin (LIT-12011034) or the Metasys IP Networks for BACnet/IP Controllers
Configuration Guide (LIT-12012458)
Processor RX63N 32-bit Renesas microcontroller
Memory 16 MB serial flash memory and 8 MB of SDRAM
Universal Input (UI) Resolution/
Configurable Output (CO) Accuracy
UI Analog Input Mode: 15-bit resolution on UIs
CO Analog Output Mode : 0–10 VDC ± 200 mV
Air Pressure Differential Sensor
Range: -1.5 in. to 1.5 in. W.C.
Performance Characteristics:
Accuracy: ±1.3% Full Span Maximum. Combined error due to offset, non-linearity, and
temperature variation. Combined error due to offset, non-linearity, and temperature
variation. (±0.039 in. W.C.)
Typical accuracy at zero (null) pressure is ±0.02 in. W.C. Includes error due to non-
linearity. (if provided)
Actuator Rating 4 N·m (35 lb·in) minimum shaft length = 44 mm (1-3/4 in.) (if provided)
Mounting Mounts to damper shaft using single set screw and to duct with single mounting screw
Dimensions
(Height x Width x Depth)
165 mm x 125 mm x 73 mm (6.5 in. x 4.92 in. x 2.9 in.)
Center of Output Hub to Center of Captive Spacer: 135 mm (5-5/16 in.)
Weight 0.65 kg (1.45 lb)
VMA1930 VAV Controller Installation Guide 19

Table 10: VMA1930 Controllers
United States:
UL Listed, File E107041, CCN PAZX, UL 916, Energy Management Equipment.
FCC Compliant to CFR47, Part 15, Subpart B, Class A.
Suitable for Use in Other Environmental Air Space (Plenums) in Accordance with Section
300.22 (C) of the National Electrical Code.
Canada:
UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205, Signal Equipment.
Industry Canada Compliant, ICES-003
Europe:
CE Mark – Johnson Controls declares that this product is in compliance with the essential
requirements and other relevant provisions of the EMC Directive; RoHS Directive
Australia and New Zealand:
RCM Mark, Australia/NZ Emissions Compliant.
Compliance
BACnet International
BACnet Testing Laboratories (BTL) Protocol Revision 15 Listed and Certified BACnet
Advanced Application Controller (B-AAC), based on the ANSI/ASHRAE 135-2016
The performance specifications are nominal and
conform to acceptable industry standard. For
application at conditions beyond these specifications,
consult the local Johnson Controls office. Johnson
Controls shall not be liable for damages resulting from
misapplication or misuse of its products.
Product warranty
This product is covered by a limited
warranty, details of which can be found at
www.johnsoncontrols.com/buildingswarranty.
Single point of contact
APAC Europe NA/SA
JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 32 CHANGJIJANG RD NEW
DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and
are subject to change without notice.
www.johnsoncontrols.com