Jolly A-7 SPOT User manual

Professional stage lighting equipment
U S E R M A N U A L

Table of content
1.Open-Package guidelines............................................................1
１.１Package................................................................................1
2.Safety instructions......................................................................1
3.Operating determination.............................................................3
4.Rigging the fixture.......................................................................4
4.1 Mounting.................................................................................4
5.
6.
7.
7.1
7.2
7.3
8.DMX protocol.............................................................................12
9.Maintance and cleaning.............................................................15
10.Electric equipment specification...............................................15
10.1 Electrical paramters............................................................15
10.2
10.3
10.5 light table .............................................16
10.7 ....................................................................18
11.Electronic drawing...................................................................19
4.2Installing the Clamps................................................................4
4.3 Power supply connection and cut off........................................5
4.4 POWER Connection.................................................................6
4.5 DMX-512 connection/connection between fixtures.................6
.......................................................15
Channel Characteristics.......................................................15
10.4 Menu Function.....................................................................15
..............................
10.6 Gobo wheel.........................................................................17
Color wheel.....
Description of the device..............................................................7
Dimension....................................................................................8
Display control.............................................................................9
Navigation in the Menu............................................................9
Display OPeration....................................................................9
Menu Maps .............................................................................11
Weight and dimensions

2.Safety instructions
1.Open-Package guidelines
１.１Package
Unpacking the fixture
1.Open the flight case cover
2.With one person on each side, lift the fixture out of the flight case.
3.Unlock pan and tilt before operating fixture.
Packing the fixture
1.Disconnect the fixture from power and allow it to cool.
2.lock arms and h as figure. (
3.Place the fix ture in the bottom of the flight case, and cover the case without forcing.
- Fig.1
ead - Fig.1 PAN Mechanism Lock and Release (every 45°)
- Fig.1-1)(Tilt Mechanism Lock and Release (every 45°) - Fig.1-2)
Congratulations on choosing our products! Please carefully read this instruction manual in its entirety and
well for using reference. This manual contained about the installation and the relative using inform
ducts.Plese refere this manual's relative when using this equipment.
This equipment is made of new style,high intensity plastic.It fully shows the modem times light charac
teristic with beauty struture. And it is made accord to CE standard. Fully agree with the internation
512 agreement.
keep it
ation of this pro instruction
teris-
tic with
standard of DMX
1.Signal cable-1PC 2.Safty cable-1PC
3.User Manval-1PC 4.Omega holder-2PCS
5.Power cable-1PC 5.Service card-1PC
When receive the product,please be careful to take and put,check if the product has damage or not be-
1
cause of transportation, and check the following parts:
This device has been shipped with our premises in absolutely perfect condition.In order to maintain this co-
ndition and toensure a safe operation,it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Every person involvd with installation and maintenance of this device to:
-Be qualilfied
-Follow the instructions of this manual.
Fig.1- 2
Level vertical transportation lock Fig.1
PAN Mechanism Lock PAN Mechanism Lock
Fig.1-1
45°
45°
45°
45°
45°
45°
45°
45°
Arm lock Arm lock
LOCK E D UNLOC K ED
Head lock
45°
45°
45°
45°

2
Never let the power-cord come into contact with other cables! Handle the power cord and all connections
with particular caution!
Make sure that the available voltage is not higher than stated on the rearpanel.
Always plug in the power plug least. Make suer that the power-switch is set to off-position before you con
ections with themains with particular caution!
Make sure that the power-cord is never crimped or damaged by sharp edges.Check the decice and the p-
ower-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power-cord by the plug,Never pull out the plug by tugging the powercord.
This device falls under protection class I.Therefore it is essential to connect the yellow/green conductor
to earth.
The electric connection,repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation(housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
t 80
c°C
IP20
t 40
a°C
Eye damage!
Avoid looking directly into the light source(meant especially for epileptics)!
Minimum distance of illuminated objects
18 metres from the lens of the projector.
Maximum ambient temperature
Do not operate the fixture if the ambient temperatuer(Ta) exceeds 40°C (104°F).
Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting,in a ther-
mally steadystate,is 80°C (176°F).
IP20 protection rating
The fitting is protected against penetration by solid of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water,rain,splashes or jets of water (second digit 0).
Indoor use only
Not suitable for household illumination
Photobiological Safety
CAUTION. Do not look directly at the light source.Do not look at the light beam with optical de-
vices or any other tool that could cause light convergence.
The fixture must be positioned so that the minimum distance between the front lens and human
eye is at least 3metres to prevent personal photobiological risks.
Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
The products to which this manual refers comply with the European Directives purs-
uant to:
•2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
•2004/108/EC - Electromagnetic Compatibility (EMC)
•2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
•2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)
Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I app-
liance according to standard EN 60598-1) .It is, moreover, recommended to protect the supply
The projector needs to be positioned so that the objects hit by the beam of light are at least
F
Risk Group 1
Accordi ng to
En62471
2.5m
750W

3
Disposing
This product is supplied in compliance with European Directive 2012/19/EU-Waste Electrical and
Electronic Equipment (WEEE). To preserve the environment please dispose/recycde this product at
the end of its life according to the local regulation.
Battery
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery.To preserve the
environment,please dispose the battery at the end of its life according to the regulation in force.
Lamp
The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the
apparatus. -Carefully read the "operating instructions" provided by the lamp manufacturer.
-Immediately replace the lamp if damaged or deformed by heat.
Maintenance
Before starting any maintenance work or cleaning the projector,cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the like
lihood of the lamp exploding is virtually small.If it is necessary to replace the lamp,wait for another 15
minutes to avoid getting burnt.The fitting is designed to hold in any splinters produced by a lamp expl-
oding.
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device ha been exposed to drastic temperature fluctuation(e.g.after transportation).do not weitch it on imm-
ediately.The arising condensation water might damage your device,Leave the device switched off until it has rea-
ched room temperature.
Never run the device without lamp!
Do not shake the device,Avoid brute force when installing or operating the device.
Never life the fixture by holding it at the projectorhead, as the mechanics may be damaged. Always hold the fixtu-
re at the transport handles.
When choosing the installation-spot,please make sure that the device is not exposed to heat,moisture or dust.Th-
ere should not be any cables lying around.You endanger your own and the safety of others!
The minimum distance between light output and the illuminated surface must be more than 0.2 meters.
Make sure that the area below the installation place is blocked when rigging,derigging or servicing the fixture.
Always fix the fixture with an appropriate safety rope, Fix the safety rope at the correct holes only.
Operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastend.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may ex-
plose and emit a hign ultraviolet radiat, which may cause burns.
The maximum ambient temperature 40°C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qua-
lified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasonsl.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void.Furthermore, any other operation may lead to dangers like short-circ-
uit,burns, electric shict,burns due to ultraviolet radiation,lamp explosion,crash etc.
3.Operating determinations
lines of the projectors from indirect contact and/orshorting to earth by using appropriately sized
residual current devices.
E
!

4
4.1 Mounting
Pay attention to the regulations of CE.
Installation by qualified staff to complete.
For the various mounting positions of the FIXTURE(standing on the floor, sideways or hanging different
accessories kits are available.
Through this a safe and firm installation is assured.
You’ll find special connectors on the bottom side of the system which are put to use here.
4.2 Installing the Clamps
Please consider the respective national norm s during the Installation!The installation must only be car-
ried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the wei-
ght for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g.an appropriate catch
net.This secondary safety attachment must be constructed in a way that no part of the installation can
fall if the main attachment fails.
When servicing the fixture staying in the area below the installation place,on bridges,under high working
places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert before taking into operation for the first time and after changes before taking into operation an-
other time.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by
a skilled person once a year.
The projector should be installed outside areas where persons m ay walk by or be seated.
Important!Overhead rigging requires extensive expering CE,including (but not limited to)calculating
working load limits, installation material being used, and periodic safety inspection of all installation ma-
terial and the projector. If you lack these qualifications, do not attempt the installation yourself, but inste-
ad use a professional structural rigger. Improper installation can result in bodilyinjury and or damage to
property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing system s have
to be used. The projector must never be fixed swinging freely in the room .
Caution Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do not install the projector!
Before rigging make sure that the installation area can hold a minim um point load of 10 times the
projector s weight.
4.Rigging the fixture

5
The projector can be placed directly on the stage floor or rigged in any orientation on atruss without alte-
ring its operation characteristics.
For overhead use,always install a safety-rope that can hold at least 10 times the weight of the fixture.You
must only use safety-ropes with screw on carabines.Pull the safety-rope through the two apertures on the
bottom of the base and over the trussing system etc.
1
2
3
4
Warning: it is necessary to make sure that
the installation location is perfectly appropriate,
and the installation location is safe and reliable.
mounting plate
secure chain
omega holder
Lock catch
4.3 Power supply connection and cut off
Connect the light source to the main power source with the plug of the power cord, or cut off the power
supply:
Connection: according to procedures, the power plug and socket is inserted into the groove one one
alignment, rotation.
Cut off: according to procedures, press the button on the rotating plug, pull out.
12
3
1
2
2
4
旋钮
灯钩
保险绳
底板
1
2
3
4
1
3

6
2 1
3
2 1
3
5 1
4 2
3
5 1
4 2
3
5 1
4 2
3
1:Ground
2:Signal( -)
3:Signal( +)
1:Ground
2:Signal( -)
3:Signal( +)
4:N.A.
5:N.A.
2 1
3
5 1
4 2
3
4.5 DMX-512 connection/connection between fixtures
Only use stereo shieded cable and 3-pin XLR-plugs and connectors in order to connect.
Warning: please verify the power of the power
supply equipment prior to the connection! Earth wire
must be grounded!
Caution
At the last fixture,the DMX-cable has to be terminated with a terminatou. solder a 120 resistor between
signal(-) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
DMX iutput
3-pin XLR socket
DMX iutput
5-pin XLR socket
DMX output
3-pin XLR socket
DMX output
5-pin XLR socket
4.4 Power Connection
mains with the enclosed power cable and plug.
If you wish to change the power supply settings, see the chapter appendix Connect the fixture to the
L
N
CABLE(EU) CABLE(US) Pin
Brown Black Live
Yellow/Green Green Earth
Light blue White Neutral
INTERNATIONAL
DMX512 DMX512

5.Description of the device
7
DMX Terminator Diagram
-For installations where the DMX cable has to run a long distance or
is In an electrically noisy environment it is recommended to use a
DMX terminator. This help in preventing corruption of the signal by
electrical noise. The DMX terminato r is simply an XLR plug witha
120 resistor connected between pins 2 and pins3, which is then
plugged into a the output XLR socket of the last ifxture in the chain.
Ω
1
2
3
120Ω
PIN2 PIN3
CINTROL PANEL
4 3
5 Power-in
6
7 5-pin XLR female
8 I
9 3
-pin XLR male
. -pin XLR female
.
.Power switch
.
.nsurance seat
. -pin XLR male
10.5
DESIGN CONSTITUTION
1.Head
2.Arm
3.Base
11 13
16
14 15
12
13.Touch screen(LCD display)
14.MODE button
15.UP button
16.DOWN button
BACK PANEL
11.
12.ENTER button
Status indicator lamp
4
8
910
5
76
1
2
3

8
17
6.Dimension
17.WDMX wire

7.Display control
7.1 Navigation in the Menu
7.2 Display Operation
Using the buttons or touch screen, and this can be simply and easily set the address code and
code.
functions
If you view or modify the lighting feature set, then press ENTER button, the display will enter the menu
interface. Both there is sub menu corresponding to the functional operation of the main menu. Each of the
menus is representative of the specific features of the lamp. The specific contents shows as the table
menu below.
Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu.Press the UP or DOWN can change the nume-
rical (increase or decrease in value).
Press the MODE button to return to menu. Set a time 1 to 10 minutes automatically exit menu interface
and close the screen.
Put through power supply, open the power switch of lamps and lanterns, display show the company
website. According to the main interface, as shown in figure:
In the main interface, press "MODE" button to view the software version, press the "UP" "DOWN" can m-
odify the DMX address.
If the screen " " icon is green,said DMX signal connection is normal, this state can be used to check th-
elamps and lanterns and connection between the control table is normal.
LOGO
9
This lamp can be set to turn off the automatic flip screen function, touch this " “ icon can be manually
flip screen.
menu interface
E12:BusErr1 01
E15:Ballast Error 0 7
E17:BD1 BUS Error 9 9
E18:BD2 BUS Error 9 9
E19:BD3 BUS Error 9 9
Mode EnterUp Down
001
1
001-021Settings
1
Main interface
A
001
1
001-020
Settings
1
Dmx Input
Wired Input
Wireless Input
Wireless In/
XLR out
Dmx Input
Mode EnterUp Down
Dmx Address
0 10
Mode EnterUp Down
Set Up
Inforamtion
Personality
Manual Control
Advanced
Mode EnterUp Down
Fixture ID
00 10
Channel Mode
Mode1 1-24
Mode2 1-24
Mode3 1-27
Mode EnterUp DownMode EnterUp Down
Press this area for 2 seconds
to modify the DMX address.
Main interface
Can view the company LOGO,web
site, hardware, software version, date.
CH-001: 000.0% 000
CH-002:PAN Fine 000.0% 000
CH-003:Tilt 000.0% 000
CH-004:Tilt Fine 000.0% 000
CH-005:Cyan 000.0% 000
CH-006:Magenta 000.0% 000
CH-007:Yellow 000.0% 000
PAN
Mode EnterUp Down

10
CODE ERRO INFO CHECK MEASURMENT NOTE
E001 SpiFlashError Check the welding of memory IC
E002 Program Err 1 Check the welding of Chip
E003 Program Err 2 Check the welding of master IC EP3C
E005 BD1Init Error
E006 BD2Init Error
E007 BD3Init Error
E012 BusErr Check main cable ABAB（485） chip
E014 SPDError Check the welding of master IC
E017 BD1 BUS Error
E018 BD2 BUS Error
E019 BD3 BUS Error
E021 Pan FB. Err
E023 Tilt FB. Err
E022 Pan Zero Err
E024 Tilt Zero Err
E025 Prism Err1
E026 Prism Err2
E027 R.Gobo Err1
E028 R.Gobo Err2
E029 A.Gobo Err
E031 Zoom Err
E032 Focus Err
E033 St. Gobo Err
E034 ColourW. Err
E035 Iris Err
E036 Cyan Err
E037 Magenta Err
E038 Yellow Err
E039 CTO Err
E040 Frost Err
E042 B.Fan1 Error
E044 B.Fan2 Error
E053 L.Fan1 Error
E055 L.Fan2 Error
Check the fan of head
Check if the fan(80) of the lamp holder is working
Check the light coupling line, optical coupling switch and a plate of
the relative position measurement
Check cable of sensor, distance and location of ,magnets and sensor
RESET
ERROR
Check the communication signal 485& 485 chip & memory IC
Check the communication signal& welding of communication chip
*Click on the main menu of the icon and value to view set of the relevant lighting information. If there is
symbol of the " " on the display, it indicates that the device may be wrong , if the symbol was blue, the
contents are errors appeared, click to clear. When the symbol is yellow, you can click on the view and
according to the references information to modify, If there is any doubt, please consult the relevant
technical personnel. (-for details see attached table).

11
7.3 Unit Menu
Remark
Dmx Address 001~XXX Dmx Address
Mode1 1~24
Mode2 1~24
Mode3 1~27
Fixture Id 0001~9999 Lamps address
Fixture Times XXXXX h XX m Total working hours
Led Times XXXXh XXm Led working hours
Reset Led Time Reset Led Time
Error List Error details
BOARD 1: XX.XX%
BOARD 2: XX.XX%
BOARD 3: XX.XX%
Fans Monitor Fans Monitor
DMX Values DMX Values
Pan Reverse ON/OFF Pan Reverse（defaul OFF）
Tilt Reverse ON/OFF Tilt Reverse（defaul OFF）
Feedback ON/OFF Pan/Tilt Auto Switch（defaul ON）
Wired Input Wired Input（defaul）
Wireless Input Wireless Input
Wireless In/XLR out Wireless In/XLR out
English
Chinese
Brightness Brightness
Screen Time out 0-10m Screen Time out
Touch Screen ON/OFF Touch Screen（defaul OFF）
Auto Screen ON/OFF Auto Screen（defaul ON）
Reset ALL
Reset Pan/Tilt
Reset Colour
Reset Gobo
Reset other
Channel Chanel Testing
Calibration lnput Password XXXX Chanel Adgusting
Factory Default ON/OFF Reset to orignal parameters
Touch Calibration Touch screen adjusting
Firware UP date Firware UP date
Screen
Manual
Control
Reset
Language language choice
Information
LED Times
Diagnosis Diagnosis
Pan/Tilt
Dmx Input
Advanced
Personality
Set up Channel Mode default Mode1

12
8.DMX protocol
Mode 1Mode 2Mode 3 Fade Type Function Dmx Value
1 20 23 Pan Pan 0-255
2 21 24 Pan Fime Pan Fime 0-255
3 22 25 Tilt Tilt 0-255
4 23 26 Tilt Fime Tilt Fime 0-255
Empty position 0
White→ red 1-19
red 20
red→green 21-39
green 40
green→blue 41-59
blue 60
blue→orange 61-79
orange 80
orange→pink 81-99
pink 100
pink→CTO 101-119
CTO 120
CTO→fluorescence 121-139
fluorescence 140
red 141-146
green 147-152
blue 153-158
orange 159-164
pink 165-170
CTO 171-182
fluorescence 183-188
CW,fast or slow 189-213
stop 214-219
CCW,slow or fast 220-243
Random slow color 244-247
Random medium color 248-251
Random fast color 252-255
6 3 4 Cyan Linear Cyan movement 0-255
7 4 5 Magenta Linear Magenta movement 0-255
8 5 6 Yellow Linear Yellow movement 0-255
9 6 7 CTO Linear CTO movement 0-255
Empty position 0-4
Gobo 1 5-7
Gobo 2 8-10
Gobo 3 11-13
Gobo 4 14-16
Gobo 5 17-19
Gobo 6 21-23
Gobo 1 24-26
Gobo 2 27-29
Gobo 3 30-32
Gobo 4 33-35
Gobo 5 36-39
Gobo 6 40-42
Gobo 1 43-72
Gobo 2 73-102
Rotation
Gobo
Select
9810
color
RotaTing gobo Select 11/9/10
Rotation - set rotation on channel 11/9/10
Gobo Shakes at variable speed from slow to fast 11/9/10
Whatever Position
5 7 8 Single step rotation
The color of the water
Random color

13
Gobo 3 103-132
Gobo 4 133-162
Gobo 5 163-192
Gobo 6 193-222
Forwards gobo wheel rotation from fast to slow 223-237
No rotation 238-240
Backwards gobo wheel rotation from slow to fast 241-255
Gobo indexing 0-255
No rotation 0-2
Forwards gobo rotation from fast to slow 3-126
No rotation 127-129
Backwards gobo rotation from slow to fast 130-253
No rotation 254-255
12 10 11 Fine Gobo
Rotation Fine Gobo Rotation 0-255
Unused Range 0-9
Gobo 1 10-19
Gobo 2 20-29
Gobo 3 30-39
Gobo 4 40-49
Gobo 5 50-59
Gobo 6 60-69
Gobo 7 70-79
Gobo 1 80-99
Gobo 2 100-119
Gobo 3 120-139
Gobo 4 140-159
Gobo 5 160-179
Gobo 6 180-199
Gobo 7 200-219
Forwards gobo wheel rotation from fast to slow 220-236
No rotation 237-238
Backwards gobo wheel rotation from slow to fast 239-255
Prism out 0-10
Prism indexing - set position on channel 15/16/17 11-138
Prism rotation - set position on channel 15/16/17 139-255
Prism indexing 0-255
No rotation 0-2
Forwards Prism rotation from fast to slow 3-126
No rotation 127-129
Backwards Prism rotation from slow to fast 130-253
No rotation 254-255
16 14 15 Frost Focus moves linearly into the light beam 0-255
Open →closed 0-131
Slow pulsation fast pulsation 132-171
Slow open,slow close- fast open,fast close 172-211
Fast open,fast close -fast open,fast close 212-251
Close 252-255
18 12 13 Animation Linear Animation disk insertion 0-255
Continuous Animation disk clockwise rotation at
linearly variable speed from fast to slow 0-124
Stop rotation 125-130
Continuous Animation disk couneter-clockwise
rotation at linearly variable speed from slow to fast 131-255
Rotation
Gobo
Select
11
14
15 17
1615
10 8 9
Animation
disk
rotation
Static
gono
Change
Rot. gobo
indexing
and
rotation
141319
1213
Gobo rotation - set position on channel 10/8/9
Iris
Gobo indexing - set position on channel 10/8/9
9 10
16 Prism
rotation
Prism
insertion
Positioning
Shaking gobos from slow to fast
Prism indexing - set position on channel 14/15/16
Prism rotation - set position on channel 14/15/16
17 1817
11
Mode1 Mode2 Mode3 Fade Type Function Dmx Value

14
Mode1 Mode2 Mode3 Fade Type Function Dmx Value
19 Zoom Zoom linearly moves from narrow to wide beam 0-255
20 Zoom Fine Fine Zoom positioning
21 Focus Focus moves linearly from far to near position 0-255
22 Focus Fine Fine focus positioning 0-255
Close 0-3
STROBE SLOW→FAST 4-103
OPen 104-107
PULSATION SLOW→FAST 108-207
Open 208-212
Random slow Strobe 213-225
Random medium Strobe 226-238
Random fast Strobe 239-251
Open 252-255
2 Dimmer Dimmer 0-100% 0-255
3 Dimmer Dimmer Fime 0-255
Unused Range 0-9
Reset Complete -3 sec 10-14
Reset CMY, CTO and color wheel only-3 sec. 15-19
Reset Other -3 sec 20-24
Reset Pan/Tilt -3 sec 25-29
Reset Gobo -3 sec 30-34
Dimmer Curve 1 =linear(1 sec) 35-39
Dimmer Curve 2 =Gamma1.5(1 sec) 40-44
Dimmer Curve 3 =Gamma2.0(1 sec) 45-49
Dimmer Curve 4 =S(1 sec) 50-54
Unused Range 55-104
Disable zoom/focuslinking-1 sec. 105-109
Enable zoom/focus linking,near distance(5meters)
(default setting)-1 sec. 110-114
Enable zoom/focus 115-119
Enable zoom/focus linking, far distance(12meters) -
1 sec. 120-124
Unused Range 125-224
Autofocus priority rotation gobo 225-229
Autofocus priority FX wheel 230-234
autofocus priority Iris 235-239
Unused Range 240-255
Function
2
272424
22 1 Stopper/
Strobe
1
23
21
18
19
20

15
9.Maintance and cleaning
It is absolutely essential that the fixture is kept clean and that dust,dirt and smoke fluid residues must not
buildup on or within the fixture. Otherwise, the fixtures light-output will be significantly reduced. Regular
cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably
through out its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended,
under no circum stances should alcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues,reduc-
ing the light-output very quickly.The cooling-fans should be cleaned monthly.
The gobos may be cleaned with a soft brush,The interior of the fixture should be cleaned at least annua-
lly usinga vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device except for the lamp and the fuse.
Replacing the fuse: If the lamp burns out,the fine-wire fuse of the device might fuse,too.Only replace the
fuse by a fuse of same type and rating.Before replacing the fuse,unplug mains lead.
Maintenance and maintenance of the operation, please contact the manufacturer or distributor.
DANGER:Disconnect from the mains before starting any maintenance work.
10.1 Electrical paramters
10.Electric equipment specification
SOURCE:
POWER:
VOLTAGE:
440W White LED
750W
AC100-240V 50/60HZ
Color temperature：8000K
10.2 Weight and dimensions
Dimensions：543X4 X5
NET WEIGHT:36Kg
Dimensions（Carton package）:657X567X661mm
WEIGHT
5
Carton package
8 66
( ):42Kg
mm
10.3 Channel Characteristics
2．Scan: Pan540°,Tilt244°,Scan speed adjustable.Fixture could auto reset.
3．Colour wheel: one open+7colors.half-color effects,CMY function.
4．Gobo wh eel:one open+6 gobos.one , Fix gobo wheel :one open+7gobos.
5．Prism system:1 rotating of 8 faces.
6．Zoom:linear amplifier.
7．Focus:linear focus wi th auto function.
8．Demme r:electronic dimmi ng,linear dimme r.
9. Strobe:electronic strobe,with strobe mode of synchronistical,pulse and random.
10. Fire wh eel:fire wh eel wi th rotation.
1．Channel:24、24、27DM X-512.
10.4 Menu Function
1． .Touch screen，English/Chinese menu

16
10.5 light table
2.Each DMX Value displayable.
3. Time of automatic turning off is able to set on the display,when operating pan/tilt,Color and gobos,
gobos, strobe are turn off and able to set freely.
4. Display the time using of lighting feature and lamp as well as the times of turning on for lamp.
5. You can switch on and off the lamp via the control panel or via your DMX controller. It must be noted
that it has to be cold before re-stricking.
6.After the DMX signal is disconnected, the display will be bright and dark.
7.Software upgrade function.
Flare diameter(m)
The minimum Angle 8.6°Flare diameter(m)
Maximum Angle36°Flare diameter(m)
Projection distance(m)
10
15
20
Φ1.52
Φ0.7 6 Φ2.28
Φ6.4 8
Φ3.2 4 Φ9.72
2130 532
25
Φ3.0 4
Φ12. 96
132
236
28920 12517 31295563
5
Φ3.8 4
Φ16. 2
85
2002
36°
36 Lux)°Illuminance(Lux)(
8.6°Illuminance(Lux)(Lux)
8.6°

17
Effect wheel
Rgobo wheel
Glass design,Inside diameter34.7mm,effective diameter 30mm.
10.6 Gobo wheel
Integra，Inside diameter 162mm,effective
diameter 25.5mm
Integra，Inside diameter mm,effective
diameter 124mm
130
Fix gobo wheel

18
10.7 Color wh eel
CTO
Magnets
Pink
blue red
Green
orange
Fluorescent