Jolly X-Beam 440 User manual

USER MANUAL

Table of content
1.Open-Package guidelines........................................................... .1
１.１Package............................................................................. ...1
2.Safety instructions................................................................... ...1
3.Operating determination....................................................... ......3
4.Rigging the fixture................................................................. ......4
4.1 Mounting.......................................................................... .......4
5.
6.
7.
7.1
7.2
7.3
8.DMX protocol........................................................................... ..12
9.Maintance and cleaning..................................................... ........16
10.Electric equipment specification........................................ .......16
10.1 Electrical paramters.......................................................... ..16
10.2
10.3
............
............
............
............
............
............
4.2Installing the Clamps............................................................................4
4.3 Power supply connection and cut off...................................................5
4.4 Power Connection...............................................................................6
4.5 DMX-512 connection/connection between fixtures.............................6
............
............
............
............
............
........
............
............
............
............
....................................................................16
Channel Characteristics...................................................................16
10.4 Menu Function.................................................................................16
10.5 light table........................................................................................17
10.6 Gobo wheel......................................................................................18
10.7 Color wheel......................................................................................19
11.Electronic drawing................................................................................20
Description of the device........................................................... ...7
Dimension.................................................................................. ..8
Display control......................................................................... ....9
Navigation in the Menu......................................................... ...9
Display Operation................................................................. ...9
Menu Maps................................................................................. 11
Weight and dimensions

Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and
the relative using information of this products. Plese refere this manual's relative instruction
when using this equipment.

2.Safety instructions
1.Open-Package guidelines
１.１Package
Unpacking the fixture
1.Open the flight case cover
2.With one person on each side, lift the fixture out of the flight case.
3.Unlock pan and tilt before operating fixture.
Packing the fixture
1.Disconnect the fixture from power and allow it to cool.
2.lock arms and h as figure. (
3.Place the fix ture in the bottom of the flight case, and cover the case without forcing.
- Fig.1
ead - Fig.2 PAN Mechanism Lock and Release (every 45°)
- Fig.2-1)(Tilt Mechanism Lock and Release (every 45°) - Fig.2-2)
This equipment is made of new style,high intensity plastic.It fully shows the modem times light charac
teristic with beauty struture. And it is made accord to CE standard. Fully agree with the internation
512 agreement.
teris-
tic with
standard of DMX
1.Signal cable-1PC 2.Safty cable-1PC
3.User Manval-1PC 4.Omega holder-2PCS
5.Power cable-1PC 5.Service card-1PC
When receive the product,please be careful to take and put,check if the product has damage or not be-
Arm lock
LOC K E D UNLO C K ED
cause of transportation, and check the following parts:
This device has been shipped with our premises in absolutely perfect condition.In order to maintain this co-
ndition and toensure a safe operation,it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Every person involvd with installation and maintenance of this device to:
-Be qualilfied
-Follow the instructions of this manual.
Fig.2-2
Level vertical transportation lock Fig.2
PAN Mechanism Lock Tilt Mechanism Lock
Fig.2-1
Aviation box Fig.1
Head lock
- 1 -
45°
45°
45°
45°
45°
45°
45°
45°
45°
45°
45°
45°

- 2 -
Never let the power-cord come into contact with other cables! Handle the power cord and all connections
with particular caution!
Make sure that the available voltage is not higher than stated on the rearpanel.
Always plug in the power plug least. Make suer that the power-switch is set to off-position before you con
ections with themains with particular caution!
Make sure that the power-cord is never crimped or damaged by sharp edges.Check the decice and the p-
ower-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power-cord by the plug,Never pull out the plug by tugging the powercord.
This device falls under protection class I.Therefore it is essential to connect the yellow/green conductor
to earth.
The electric connection,repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation(housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
t 80
c°C
IP20
t 40
a°C
Eye damage!
Avoid looking directly into the light source(meant especially for epileptics)!
Minimum distance of illuminated objects
18 metres from the lens of the projector.
Maximum ambient temperature
Do not operate the fixture if the ambient temperatuer(Ta) exceeds 40°C (104°F).
Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting,in a ther-
mally steadystate,is 80°C (176°F).
IP20 protection rating
The fitting is protected against penetration by solid of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water,rain,splashes or jets of water (second digit 0).
Indoor use only
Not suitable for household illumination
Photobiological Safety
CAUTION. Do not look directly at the light source.Do not look at the light beam with optical de-
vices or any other tool that could cause light convergence.
The fixture must be positioned so that the minimum distance between the front lens and human
eye is at least 3metres to prevent personal photobiological risks.
Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
The products to which this manual refers comply with the European Directives purs-
uant to:
•2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
•2004/108/EC - Electromagnetic Compatibility (EMC)
•2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
•2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)
Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I app-
liance according to standard EN 60598-1) .It is, moreover, recommended to protect the supply
The projector needs to be positioned so that the objects hit by the beam of light are at least
F
Risk Gr oup 1
Accor ding to
En624 71

Disposing
This product is supplied in compliance with European Directive 2012/19/EU-Waste Electrical and
Electronic Equipment (WEEE) . To preserve the environment please dispose/recycde this product at
the end of its life according to the local regulation.
Battery
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery.To preserve the
environment,please dispose the battery at the end of its life according to the regulation in force.
Lamp
The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the
apparatus. -Carefully read the "operating instructions" provided by the lamp manufacturer.
-Immediately replace the lamp if damaged or deformed by heat.
Maintenance
Before starting any maintenance work or cleaning the projector,cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the like
lihood of the lamp exploding is virtually small.If it is necessary to replace the lamp,wait for another 15
minutes to avoid getting burnt.The fitting is designed to hold in any splinters produced by a lamp expl-
oding.
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device ha been exposed to drastic temperature fluctuation(e.g.after transportation).do not weitch it on imm-
ediately.The arising condensation water might damage your device,Leave the device switched off until it has rea-
ched room temperature.
Never run the device without lamp!
Do not shake the device,Avoid brute force when installing or operating the device.
Never life the fixture by holding it at the projectorhead, as the mechanics may be damaged. Always hold the fixtu-
re at the transport handles.
When choosing the installation-spot,please make sure that the device is not exposed to heat,moisture or dust.Th-
ere should not be any cables lying around.You endanger your own and the safety of others!
The minimum distance between light output and the illuminated surface must be more than 0.2 meters.
Make sure that the area below the installation place is blocked when rigging,derigging or servicing the fixture.
Always fix the fixture with an appropriate safety rope, Fix the safety rope at the correct holes only.
Operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastend.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may ex-
plose and emit a hign ultraviolet radiat, which may cause burns.
The maximum ambient temperature 40°C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qua-
lified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasonsl.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void.Furthermore, any other operation may lead to dangers like short-circ-
uit,burns, electric shict,burns due to ultraviolet radiation,lamp explosion,crash etc.
3.Operating determinations
lines of the projectors from indirect contact and/orshorting to earth by using appropriately sized
residual current devices.
E
!
- 3 -

4.1 Mounting
For the various mounting positions of the FIXTURE(standing on the floor, sideways or hanging different
accessories kits are available.
Through this a safe and firm installation is assured.
You’ll find special connectors on the bottom side of the system which are put to use here.
4.2 Installing the Clamps
Please consider the respective national norm s during the Installation!The installation must only be car-
ried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the wei-
ght for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g.an appropriate catch
net.This secondary safety attachment must be constructed in a way that no part of the installation can
fall if the main attachment fails.
When servicing the fixture staying in the area below the installation place,on bridges,under high working
places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert before taking into operation for the first time and after changes before taking into operation an-
other time.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by
a skilled person once a year.
The projector should be installed outside areas where persons m ay walk by or be seated.
Important!Overhead rigging requires extensive expering CE,including (but not limited to)calculating
working load limits, installation material being used, and periodic safety inspection of all installation ma-
terial and the projector. If you lack these qualifications, do not attempt the installation yourself, but inste-
ad use a professional structural rigger. Improper installation can result in bodilyinjury and or damage to
property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing system s have
to be used. The projector must never be fixed swinging freely in the room .
Caution Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do not install the projector!
Before rigging make sure that the installation area can hold a minim um point load of 10 times the
projector s weight.
4.Rigging the fixture
Pay attention to the regulations of CE.
Installation by qualified staff to complete.
- 4 -

The projector can be placed directly on the stage floor or rigged in any orientation on atruss without alte-
ring its operation characteristics.
For overhead use,always install a safety-rope that can hold at least 10 times the weight of the fixture.You
must only use safety-ropes with screw on carabines.Pull the safety-rope through the two apertures on the
bottom of the base and over the trussing system etc.
1
2
3
4
mounting plate
secure chain
omega holder
Lock catch
12
3
1
2
- 5 -
Warning: it is necessary to make sure that
the installation location is perfectly appropriate,
and the installation location is safe and reliable.
4.3 Power supply connection and cut off
Connect the light source to the main power source with the plug of the power cord, or cut off the power
supply:
Connection: according to procedures, the power
plug and socket is inserted into the groove one one
alignment,rotation.
Cut off:according to procedures,press the button
on the rotating plug,pull out.
2
1
43

2 1
3
2 1
3
5 1
4 2
3
5 1
4 2
3
5 1
4 2
3
1:Ground
2:Signal(-)
3:Signal(+)
1:Ground
2:Signal(-)
3:Signal(+)
4:N.A.
5:N.A.
2 1
3
5 1
4 2
3
4.5 DMX-512 connection/connection between fixtures
Only use stereo shieded cable and 3-pin XLR-plugs and connectors in order to connect.
Caution
At the last fixture,the DMX-cable has to be terminated with a terminatou. solder a 120 resistor between
signal(-) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
DMX iutput
3-pin XLR socket
DMX iutput
5-pin XLR socket
DMX output
3-pin XLR socket
DMX output
5-pin XLR socket
4.4 Power Connection
mains with the enclosed power cable and plug.
If you wish to change the power supply settings, see the chapter appendix Connect the fixture to the
L
N
CABLE(EU) CABLE(US) Pin
Brown Black Live
Yellow/Green Green Earth
Light blue White Neutral
INTERNATIONAL
Warning: please verify the power of the power
supply equipment prior to the connection! Earth wire
must be grounded!
- 6 -
DMX512 DMX512

5.Description of the device
DMX Terminator Diagram
-For installations where the DMX cable has to run a long distance or
is In an electrically noisy environment it is recommended to use a
DMX terminator. This help in preventing corruption of the signal by
electrical noise. The DMX terminato r is simply an XLR plug witha
120 resistor connected between pins 2 and pins3, which is then
plugged into a the output XLR socket of the last ifxture in the chain.
Ω
1
2
3
120Ω
PIN2 PIN3
- 7 -
Head
Tilt °,
244 Fixture could auto
reset.
3.
Arm
Pan °,540 Fixture could auto
reset.
Base
2.
1.
17.WDMX wire
BACK PANEL
4.3-pin XLR female
5.5-pin XLR female
6.Power-in
7. Power switch
8.Main Fuse
9.5-pin XLR male
10.3-pin XLR male
CINTROL PANEL
11.Status indicator lamp
12.Touch screen(LCD display)
13.MODE button
14.UP button
15.DOWN button
16.ENTER button
17.WDMX Wire
4 65 7
10 9 8
11 12 1314
16 15

6.Dimension
- 8 -

7.Display control
7.1 Navigation in the Menu
7.2 Display Operation
Using the buttons or touch screen, and this can be simply and easily set the address code and
code.
functions
If you view or modify the lighting feature set, then press ENTER button, the display will enter the menu
interface. Both there is sub menu corresponding to the functional operation of the main menu. Each of the
menus is representative of the specific features of the lamp. The specific contents shows as the table
menu below.
Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu.Press the UP or DOWN can change the nume-
rical (increase or decrease in value).
Press the MODE button to return to menu. Set a time 0 to 10 minutes automatically exit menu interface
and close the screen.
Put through power supply, open the power switch of lamps and lanterns, display show the company
website. According to the main interface, as shown in figure:
In the main interface, press "MODE" button to view the software version, press the "UP" "DOWN" can m-
odify the DMX address.
If the screen " " icon is green,said DMX signal connection is normal, this state can be used to check th-
elamps and lanterns and connection between the control table is normal.
LOGO
This lamp can be set to turn off the automatic flip screen function, touch this " “ icon can be manually
flip screen.
- 9 -
menu interface
E12:BusErr1 01
Mode EnterUp Down
001
1
001-022Se t t ing s
1
Main interface
A
001
1
001-022
Sett ings
1
Dmx Input
Wired Input
Wireless Input
Wireless In/
XLR out
Dmx Input
Mode EnterUp Down
Dmx Address
0 10
Mode EnterUp Down
Set Up
Inforamtion
Personality
Manual Control
Advanced
Mode EnterUp Down
Fixture ID
00 10
Lamp Control
ON
OFF
Confirm
Channel Mode
Mode1 1-22
Mode2 1-22
Mode3 1-16
Mode EnterUp Down Mode EnterUp DownMode EnterUp Down
Press this area for 2 seconds
to modif y the DMX address.
Main interface
Can vi ew the company LOGO ,web
site , hardware, softw are version, date.
CH-001: 000.0 % 000
CH-002:PAN Fine 0 00.0% 000
CH-003:Tilt 000.0% 000
CH-004:Tilt Fine 000.0% 000
CH-005:Colour 1 000.0% 000
CH-006:Rotation Gobo Select 000.0% 000
CH-007:R.gobo indexing and rotation 0 00.0% 000
CH-008:R.gobo indexing and rotation-fine 0 00.0 % 000
CH-009:Static gobo wheel 000.0% 000
CH-010:Prism 0 00.0 % 000
PAN
Mode EnterUp Down

Click on the main interface of the icon, numerical to view view Settings related information of lamps and
lanterns.Symbols such as the main interface appear “ “,the following error message indicates that there
might be a lamps and lanterns,can click to view and control information content to modify the lamps and
lanterns.
- 10 -
CODE ERRO INFO CHECK MEASURMENT NOTE
E01 SpiFlashError Check the welding of memory IC
E02 Program Err 1 Check the welding of Chip
E03 Program Err 2 Check the welding of master IC EP3C
E04 MBDInit Error
E05 BD1Init Error
E06 BD2Init Error
E07 BD3Init Error
E12 BusErr1
E13 BusErr2
E14 SPDError Check the welding of master IC
E16 MFpga Error
E17 BD1 BUS Error
E18 BD2 BUS Error
E19 BD3 BUS Error
E21 Pan FB. Err
E23 Tilt FB. Err
E22 Pan Zero Err
E24 Tilt Zero Err
E25 Prism Err1
E26 Prism Err2
E27 Prism RtErr1
E28 Prism RtErr2
E29 R.Gobo Err1
E30 R.Gobo Err2
E32 Focus Err
E33 St.Gobo Err
E34 Colour Err
E37 B.Fan1 Error
E38 B.Fan2 Error
E39 B.Fan3 Error
E40 L.Fan1 Error
E41 L.Fan2 Error
E42 L.Fan3 Error
E43 L.Fan4 Error
E44 GOBO Fan Error Check the fan of head GOBO
E45 EthMDL Error Check the fan of ArtNet、communication signal
Check the communication signal 485& 485 chip & memory IC
Check the fan of head
Check cable of sensor, distance and location of ,magnets and
sensor
Check the light coupling line, optical coupling switch and a
plate of the relative position measurement
RESET
ERROR
Check if the blowing machine of lamp holder is working
Check if the fan(80) of the lamp holder is working
Check the communication signal& welding of communication
chip
Check main cable ABAB（485） chip

7.3 Unit Menu
- 11 -
Remark
Dmx Address 001~XXX Dmx Address
Mode1 1~22
Mode2 1~22
Mode3 1~16
Fixture Id 0001~9999 Lamps address
IP Address
Net Mask
Universe
Fixture Times XXXXX h XX m Total working hours
Lamp On Times XXXXh XXm Lamp On working hours
Lamp Strike XXXX Lamp Strike
Reset Lamp Time Reset Lamp Time
Error List Error details
BOARD 1: XX.XX%
BOARD 2: XX.XX%
BOARD 3: XX.XX%
Fans Monitor Fans Monitor
DMX Values DMX Values
Power ON Light ON/OFF Power ON Light(default OFF)
Lamp On By DMX ON/OFF Lamp On By DMX(default ON)
Lamp ON Delay 0~60m Lamp ON Delay(defaul 0m)
Pan Reverse ON/OFF Pan Reverse(defaul OFF)
Tilt Reverse ON/OFF Tilt Reverse(defaul OFF)
Feedback ON/OFF Pan/Tilt Auto Switch(defaul ON)
Wired Input Wired Input(defaul)
Wireless Input Wireless Input
(use it under the module with Wireless)
Wireless In/XLR out Wireless In/XLR out
(use it under the module with Wireless)
Art-Net Input Art-Net Input
(use it under the module with art-net)
Art-Net In/XLR out Art-Net In/XLR out
(use it under the module with art-net)
Brightness Brightness
Screen Time out 0-10m Screen Time out
Touch Screen ON/OFF Touch Screen(defaul OFF)
Auto Screen ON/OFF Auto Screen(defaul ON)
English
Chinese
Lamp Control ON/OFF Lamp Control(defaul OFF)
Confirm Confirm
Reset ALL
Reset Pan/Tilt
Reset Colour
Reset Focus
Reset Dimmer
Channel Chanel Testing
Calibration lnput Password XXXX Chanel Adgusting
Factory Default ON/OFF Reset to orignal parameters
Touch Calibration Touch screen adjusting
default Mode1Channel Mode
Personality
Screen
Manual
Control
Lamp
Reset
Language
Information
Lamp Times
Diagnosis Diagnosis
Lamp
Pan/Tilt
Dmx Input
Advanced
language choice
Set up
Network Setup Art-Net Set up

8.DMX protocol
- 12 -
Mode1 Mode2 Mode3 Fade Type Function Dmx
Value
1 15 14 Pan Pan 0-255
2 16 Pan Fime Pan Fime 0-255
3 17 15 Tilt Tilt 0-255
4 18 Tilt Fime Tilt Fime 0-255
Empty position 0-3
Empty → colour 1 4-12
colour 1 → colour 2 13-21
colour 2 → colour 3 22-30
colour 3 → colour 4 31-39
colour 4 → colour 5 40-48
colour 5 → colour 6 49-57
colour 6 → colour 7 58-66
colour 7 → colour 8 67-75
colour 8 → colour 9 76-84
colour 9 → colour 10 85-93
colour 10 → colour 11 94-102
colour 1 103-107
colour 2 108-112
colour 3 113-117
colour 4 118-122
colour 5 123-127
colour 6 128-132
colour 7 133-137
colour 8 138-142
colour 9 143-147
colour 10 148-152
colour 11 153-157
Continuous gobo rotation at linearly variable
speed from fast to slow 158-201
Stop rotation 202-205
Continuous gobo rotation at linearly variable
speed from slow to fast 206-249
Auto random colour selection from fast to slow 250-255
RotaTing gobo Select 0
Empty position 1-4
Gobo 1 5-7
Gobo 2 8-10
Gobo 3 11-13
Gobo 4 14-16
Gobo 5 17-19
Gobo 6 20-22
Gobo 7 23-25
Gobo 8 26-28
Gobo 9 29-31
Gobo 1 32-34
Gobo 2 35-37
Gobo 3 38-40
Gobo 4 41-43
Gobo 5 44-46
Gobo 6 47-49
Gobo 7 50-52
Gobo 8 53-55
566
Positioning
Colour 1
Continual positioning
Gobo Shakes at variable speed from slow to fast.
Rotation
Gobo
Select
5 1 1

- 13 -
Mode1 Mode2 Mode3 Fade Type Function Dmx
Value
Gobo 9 56-59
Gobo 1 60-67
Gobo 2 68-75
Gobo 3 76-83
Gobo 4 84-91
Gobo 5 92-99
Gobo 6 100-107
Gobo 7 108-115
Gobo 8 116-123
Gobo 9 124-129
Gobo 1 130-137
Gobo 2 138-145
Gobo 3 146-153
Gobo 4 154-161
Gobo 5 162-169
Gobo 6 170-177
Gobo 7 178-185
Gobo 8 186-193
Gobo 9 194-199
Empty position 200 - 201
Continuous gobo rotation at linearly variable
speed from fast to slow 202 - 221
Stop rotation 222 - 223
Continuous gobo rotation at linearly variable
speed from slow to fast 224 - 243
Auto random gobo selection from fast to slow 244 - 255
Gobo indexing 0-255
No rotation 0
Forwards gobo rotation from fast to slow 1-127
No rotation 128-129
Backwards gobo rotation from slow to fast 130-255
8 8 7
Rot.gobo
indexing and
rotation-fine
Fine indexing (rotation) 0-255
Open/hole 0-3
Gobo 1 4-7
Gobo 2 8-11
Gobo 3 12-15
Gobo 4 16-18
Gobo 5 19-22
Gobo 6 23-26
Gobo 7 27-30
Gobo 8 31-34
Gobo 9 35-37
Gobo 10 38-41
Gobo 11 42-45
Gobo 12 46-49
Gobo 13 50-53
Gobo 14 54-56
Gobo 15 57-60
Gobo 16 61-64
Gobo 17 65-68
566
Gobo Shakes at variable speed from slow to fast.
Shaking gobos from slow to fast.
Rotation
Gobo
Select
Static gobo
wheel
45
Gobo indexing - set position on channel 6/6/5
Gobo rotation - set position on channel 6/6/5
Rot. gobo
indexing and
rotation
7 7 6
9

- 14 -
Mode1 Mode2 Mode3 Fade Type Function Dmx
Value
Gobo 18 69-71
Continuous gobo rotation at linearly variable
speed from fast to slow 72-113
Stop rotation 114-117
Continuous gobo rotation at linearly variable
speed from slow to fast 118-159
Gobo 1 160-165
Gobo 2 166-170
Gobo 3 171-175
Gobo 4 176-181
Gobo 5 182-186
Gobo 6 187-191
Gobo 7 192-197
Gobo 8 198-202
Gobo 9 203-207
Gobo 10 208-214
Gobo 11 215-218
Gobo 12 219-223
Gobo 13 224-229
Gobo 14 230-234
Gobo 15 235-239
Gobo 16 240-245
Gobo 17 246-250
Gobo 18 251-255
Open position 0-9
18-facet circular rotating prism-rotation 10-91
8-facet circular rotating prism-rotation 92-173
18+8-facet circular rotating prism-rotation 174-255
Prism indexing(0-540) 0-127
Forwards 18 prism rotation from fast to slow 128-190
No rotation 191-192
Backwards 18prism rotation from slow to fast 193-255
Prism indexing(0-540) 0-127
Forwards 8 prism rotation from fast to slow 128-190
No rotation 191-192
Backwards 8 prism rotation from slow to fast 193-255
13 12 11 Forst Frost from 0% to 100% 0-255
14 13 12 Focus Continuous adjustment from far to near 0-255
15 14 13 Focus fine Fine focusing 0-255
Shutter closed 0-3
Strobe-effect from slow to fast 4-103
Shutter open 104-107
Opening pulse in sequences from slow to fast 108-207
Shutter open 208-212
RANDOM SLOW STROBE 213-225
RANDOM MEDIUM STROBE 226-238
RANDOM FAST STROBE 239-251
Shutter open 252-255
17 3 3 Dimmer Dimmer 0-100% 0-255
18 4 Dimmer Fime Dimmer Fime 0-255
Unused Range 0-11
Fast Pan/Tilt Speed（default） 12-24
Normal Pan/Tilt Speed 25-37
normal dimmer(default) 38-50
linear dimmer 51-62
459
Function161919
16 2 2
11 10
Shaking gobos from slow to fast
9
Prism
18 Prism
rotation and
indexing
8 Prism
rotation and
indexing
Strobe
Static gobo
wheel
10 9 8
11 10
12

- 15 -
Mode1 Mode2 Mode3 Fade Type Function Dmx
Value
Effects Reset -5 sec 63-75
Pan/Tilt Reset 76-87
Total reset 88-101
Lamp Off -5 sec 102-114
Lamp On -5 sec 115-234
Unused Range 235-255
20 20 Pan-Tilt time Pan-Fine Pan-Tilt-Tilt Fine 0-255
21 21 Colour time Cyan - Magenta - Yellow 0-255
22 22 Gobo time Static Gobo-Rotating Gobo 0-255
19 19 16 Function
Time table
BIT Seconds
0 Full
1 0.2
2 0.4
3 0.6
4 0.8
5 1
6 1.2
7 1.4
8 1.6
9 1.8
10 2
11 2.2
12 2.4
13 2.6
14 2.8
15 3
16 3.2
17 3.4
18 3.6
19 3.8
20 4
21 4.2
22 4.4
23 4.6
24 4.8
25 5
26 5.2
27 5.4
28 5.6
29 5.8
30 6
31 6.2
32 6.4
33 6.6
34 6.8
35 7
36 7.2
37 7.4
38 7.6
39 7.8
40 8
41 8.2
42 8.4
BIT Seconds
43 8.6
44 8.8
45 9
46 9.2
47 9.4
48 9.6
49 9.8
50 10
51 10.2
52 10.4
53 10.6
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
22
23
20
21
18
19
14
15
11
12
13
16
17
BIT Seconds
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
39
40
37
38
35
36
31
32
29
30
24
25
26
33
34
27
28
BIT Seconds
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
55
56
57
53
54
51
52
47
48
46
41
42
49
50
43
44
45
BIT Seconds
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
140
150
160
120
130
100
110
80
85
70
75
58
59
90
95
60
65
BIT Seconds
215 160
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255 Full
310
290
300
270
280
230
240
210
220
170
180
250
260
190
200

- 16 -
9.Maintance and cleaning
It is absolutely essential that the fixture is kept clean and that dust,dirt and smoke fluid residues must not
buildup on or within the fixture. Otherwise, the fixtures light-output will be significantly reduced. Regular
cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably
through out its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended,
under no circum stances should alcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues,reduc-
ing the light-output very quickly.The cooling-fans should be cleaned monthly.
The gobos may be cleaned with a soft brush,The interior of the fixture should be cleaned at least annua-
lly usinga vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device except for the lamp and the fuse.
Replacing the fuse: If the lamp burns out,the fine-wire fuse of the device might fuse,too.Only replace the
fuse by a fuse of same type and rating.Before replacing the fuse,unplug mains lead.
Maintenance and maintenance of the operation, please contact the manufacturer or distributor.
DANGER:Disconnect from the mains before starting any maintenance work.
10.1 Electrical paramters
10.Electric equipment specification
SOURCE:
POWER:
VOLTAGE:
Osram sirius hri 440W
700W
AC100-240V 50/60HZ
Color temperature：7000K
10.2 Weight and dimensions
Dimensions：424X423X560
NET WEIGHT:28Kg
Dimensions
WEIGHT
Dimensions
NET WEIGHT/WEIGHT
mm
（ ）:661X506X581mm
( ):34Kg
（Air boxes -2 lights):1010X520X780mm
(Air boxes -2 lights) :37Kg/97Kg
Carton package
Carton package
10.3 Channel Characteristics
2．Scan: Pa n540°,Tilt244°,Scan speed adjustable.Fi xture could auto reset.
3．Colour wh eel:one open+11colors.half-color effects.
4．Gobo wh eel:one open+9 gobos.Fix gobo wheel :one open+18gobos.
5．Prism system:one 8 faces wi th rotation, one 18 faces with rotation and both prisms can be overlapped.
6．Frost: linear frost.
7．Focus:linear focus wi th auto function.
8．Demme r:two stepper mo tor adjusting,linear dimme r.
9. Strobe:two stepper mo tor,wi th strobe mode of synchronistical,pulse and random.
1．Channel:22、22、16DMX -512.
10.4 Menu Function
1． .Touch screen，English/Chinese menu