Jolly LT-1516 User manual

USER MANUAL
Version:1.1

Table of content
1.Open-Package guidelines........................................................... .1
１.１Package............................................................................. ...1
2.Safety instructions................................................................... ...1
3.Operating determination....................................................... ......2
4.Rigging the fixture................................................................. ......3
4.1 Mounting.......................................................................... .......3
5.
6.
7.
7.1
7.2
7.3
8.DMX protocol........................................................................... ..11
9.Maintance and cleaning..................................................... ........14
10.Electric equipment specification........................................ .......15
10.1 Electrical paramters.......................................................... ..15
10.2
10.3
............
............
............
............
............
............
4.2Installing the Clamps............................................................................3
4.3 Power supply connection and cut off...................................................4
4.4 Power Connection...............................................................................4
4.5 DMX-512 connection/connection between fixtures.............................4
............
............
............
............
............
........
............
............
............
............
....................................................................15
Channel Characteristics...................................................................15
10.4 Menu Function.................................................................................15
11.Electronic drawing................................................................................16
Description of the device........................................................... ...6
Dimension.................................................................................. ..6
Display control......................................................................... ....7
Navigation in the Menu......................................................... ...7
Display Operation................................................................. ...7
Menu Maps................................................................................. 8
Weight and dimensions

Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and
the relative using information of this products. Plese refere this manual's relative instruction
when using this equipment.

2.Safety instructions
1.Open-Package guidelines
１.１Package
Unpacking the fixture
1.Open the flight case cover.
2.With one person on each side, lift the fixture out of the flight case.
Packing the fixture
1.Disconnect the fixture from power and allow it to cool.
2. djust the rotating support ,place it in the box.A
This equipment is made of new style,high intensity plastic.It fully shows the modem times light charac
teristic with beauty struture. And it is made accord to CE standard. Fully agree with the internation
512 agreement.
teris-
tic with
standard of DMX
1.Signal cable-1PC 2.Safty cable-1PC
3.User Manval-1PC 4. glare shield-1PCS
5.Power cable-1PC 5.Service card-1PC
When receive the product,please be careful to take and put,check if the product has damage or not be-
cause of transportation, and check the following parts:
This device has been shipped with our premises in absolutely perfect condition.In order to maintain this co-
ndition and toensure a safe operation,it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
Every person involvd with installation and maintenance of this device to:
-Be qualilfied
-Follow the instructions of this manual.
- 1 -
Never let the power-cord come into contact with other cables! Handle the power cord and all connections
with particular caution!
Make sure that the available voltage is not higher than stated on the rearpanel.
Always plug in the power plug least. Make suer that the power-switch is set to off-position before you con
ections with themains with particular caution!
Make sure that the power-cord is never crimped or damaged by sharp edges.Check the decice and the p-
ower-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power-cord by the plug,Never pull out the plug by tugging the powercord.
This device falls under protection class I.Therefore it is essential to connect the yellow/green conductor
to earth.
The electric connection,repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
Do not touch the device’s housing bare hands during its operation(housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
Eye damage!
Avoid looking directly into the light source(meant especially for epileptics)!

- 2 -
t 90
c°C
IP 65
t 40
a°C
Risk Group 2
According to
En62471
Minimum distance of illuminated objects
0.20 metres (8”) from the lens of the projector.
Maximum ambient temperature
Do not operate the fixture if the ambient temperatuer(Ta) exceeds 40°C (104°F).
Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting,in a ther-
mally steadystate,is 90°C (194°F).
IP65 protection rating
Completely prevent external intrusion and dust entering. Avoid the damages to devi-
ces of water coming from the nozzle from different directions.
Indoor use only
Not suitable for household illumination
Photobiological Safety
CAUTION.Possibly hazardous optical radiation emitted from this product.Do not stare at
operating lamp.May be harmful to the eyes.
Light collimation system
This product contains internal light collimation system.Avoid intense light from any angle.
The products to which this manual refers comply with the European Directives purs-
uant to:
•2006/95/EC - Safety of electrical equipment supplied at low voltage ( LVD)
•2004/108/EC - Electromagnetic Compatibility (EMC)
•2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
•2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)
Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I app-
liance according to standard EN 60598-1) .It is, moreover, recommended to protect the supply
lines of the projectors from indirect contact and/orshorting to earth by using appropriately
sized residual current devices.
The projector needs to be positioned so that the objects hit by the beam of light are at least
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device ha been exposed to drastic temperature fluctuation(e.g.after transportation).do not weitch it on imm-
ediately.The arising condensation water might damage your device,Leave the device switched off until it has rea-
ched room temperature.
Never run the device without lamp!
Do not shake the device,Avoid brute force when installing or operating the device.
Never life the fixture by holding it at the projectorhead, as the mechanics may be damaged. Always hold the fixtu-
re at the transport handles.
When choosing the installation-spot,please make sure that the device is not exposed to heat,moisture or dust.Th-
ere should not be any cables lying around.You endanger your own and the safety of others!
The minimum distance between light output and the illuminated surface must be more than 0.2 meters.
Make sure that the area below the installation place is blocked when rigging,derigging or servicing the fixture.
3.Operating determinations

Always fix the fixture with an appropriate safety rope, Fix the safety rope at the correct holes only.
Operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastend.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may ex-
plose and emit a hign ultraviolet radiat, which may cause burns.
The maximum ambient temperature 40°C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not qua-
lified for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modifications on the device are forbidden due to safety reasonsl.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void.Furthermore, any other operation may lead to dangers like short-circ-
uit,burns, electric shict,burns due to ultraviolet radiation,lamp explosion,crash etc.
- 3 -
4.1 Mounting
For the various mounting positions of the FIXTURE(standing on the floor, sideways or hanging different
accessories kits are available.
Through this a safe and firm installation is assured.
You’ll find special connectors on the bottom side of the system which are put to use here.
4.2 Installing the Clamps
Please consider the respective national norm s during the Installation!The installation must only be car-
ried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the wei-
ght for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g.an appropriate catch
net.This secondary safety attachment must be constructed in a way that no part of the installation can
fall if the main attachment fails.
When servicing the fixture staying in the area below the installation place,on bridges,under high working
places and other endangered areas is forbidden.
4.Rigging the fixture
Pay attention to the regulations of CE.
Installation by qualified staff to complete.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert before taking into operation for the first time and after changes before taking into operation an-
other time.
The operator has to make sure that safety-relating and machine-technical installations are approved by
an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by
a skilled person once a year.

The projector should be installed outside areas where persons m ay walk by or be seated.
Important!Overhead rigging requires extensive expering CE,including (but not limited to)calculating
working load limits, installation material being used, and periodic safety inspection of all installation ma-
terial and the projector. If you lack these qualifications, do not attempt the installation yourself, but inste-
ad use a professional structural rigger. Improper installation can result in bodilyinjury and or damage to
property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing system s have
to be used. The projector must never be fixed swinging freely in the room .
Caution Projectors may cause severe injuries when crashing down! If you have doubts concerning the
safety of a possible installation, do not install the projector!
Before rigging make sure that the installation area can hold a minim um point load of 10 times the
projector s weight.
- 4 -
The projector can be placed directly on the stage floor or rigged in any orientation on atruss without alte-
ring its operation characteristics.
For overhead use,always install a safety-rope that can hold at least 10 times the weight of the fixture.You
must only use safety-ropes with screw on carabines.Pull the safety-rope through the two apertures on the
bottom of the base and over the trussing system etc.
Warning: it is necessary to make sure that
the installation location is perfectly appropriate,
and the installation location is safe and reliable.
4.3 Power supply connection and cut off
Connect the light source to the main power source with the plug of the power cord, or cut off the power
supply:
Warning: please verify the power of the power
supply equipment prior to the connection! Earth wire
must be grounded!
4.4 Power Connection
mains with the enclosed power cable and plug.
If you wish to change the power supply settings, see the chapter appendix Connect the fixture to the
L
N
CABLE(EU) CABLE(US) Pin
Brown Black Live
Yellow/Green Green Earth
Light blue White Neutral
INTERNATIONAL
4.5 DMX-512 connection/connection between fixtures
Only use stereo shieded cable and 3-pin XLR-plugs and connectors in order to connect.

- 5 -
5 1
4 2
3
5 1
4 2
3
5 1
4 2
3
1:Ground
2:Signal(-)
3:Signal(+)
4:N.A.
5:N.A.
5 1
4 2
3
Caution
At the last fixture,the DMX-cable has to be terminated with a terminatou. solder a 120 resistor between
signal(-) and Signal (+) into a 5-pin XLR-plug and plug it in the DMX-output of the last fixture.
DMX iutput
5-pin XLR socket
DMX output
5-pin XLR socket
DMX Terminator Diagram
-For installations where the DMX cable has to run a long distance or
is In an electrically noisy environment it is recommended to use a
DMX terminator. This help in preventing corruption of the signal by
electrical noise. The DMX terminato r is simply an XLR plug witha
120 resistor connected between pins 2 and pins3, which is then
plugged into a the output XLR socket of the last ifxture in the chain.
Ω
1
2
3
12 0Ω
PIN2 PIN3
DMX512

- 6 -
5.Description of the device
6.Dimension
1.
2.
4.
7.
8.
9.
Power-In
Power-Out
ENTER button
DOWN button
UP button
MODE button
LED display
10.Respirator
3-pin XLR male
3.3-pin XLR female
5.
6.
10
1 2
34
9
5
6
7
8
1007
108
121
97
153
181

- 7 -
7.Display control
7.1 Navigation in the Menu
7.2 Display Operation
Using the buttons, and this can be simply and easily set the address code and function code.
If you view or modify the lighting feature set, then press ENTER button, the display will enter the menu
interface. Both there is sub menu corresponding to the functional operation of the main menu. Each of the
menus is representative of the specific features of the lamp. The specific contents shows as the table
menu below.
Set or browse lighting function, press UP or DOWN button.
Press ENTER to save your changes or enter the submenu.Press the UP or DOWN can change the nume-
rical (increase or decrease in value).
Press the MODE button to return to menu.
-When the power on, if the display is flashing, it indicates that the DMX signal connection is unnormal.
-Once powering on, the display indicates as following:
>Main
DMX
>Main
Personality
>Main
Stand-Alone
>Main
Service
>Main
Information
menu interface
Main interface
CLIKE ENTER OF HOME PAGE TO SELECT:
Mode
DMXA 0 0 1
Std.12
DMX address code

- 8 -
If there is a channel failure in the reset process, the LCD screen will display the corresponding fault info-
rmation, can be compared to the information content of the lamp to be amended, if in doubt, consult the re-
levant technical personnel. - (Error List)
7.3 Menu Maps
CODE #
ERRO INFO CHECK MEASURMENT NOTE
E01 SpiErr Check the welding of memory IC
E02 PrgErr 1 Upgrade again
E03 BD1Err
E04 BD2Err
E05 BD3Err
RESET
ERROR
Check main cable ABAB（485） chip
Adress 1-XXX
Standard - 12 *
Advanced - 17
Pattern - 27
RGBW - 4
Easy - - 6
Pixel - 76
PIX RGBW - 64
PIX Dim - 28
Rocket-85
On *
Off
Reset via DMX ON*/OFF
Closed *
Hold
Play P 1
Play P 2
Play P 3
Refresh xxx Hz
Color 0-255
Red 0-255
Green 0-255
Blue 0-255
White 0-255
Shutter 0-255
Dimmer 0-255
CTO 0-255
Patt 0-255
Patt Sp 0-255
Patt Fa 0-255
DMX
Mode
RDM
No DMX
DMX Live

- 9 -
Linear *
Theat
Square
Inv Sq
Fast *
Smooth
500 Hz
1000 Hz *
2000 Hz
4000 Hz
OFF
1 Min *
5 Min
60 Min
ON*
OFF
Celsius *
Fahrenh
OFF *
ON
Password **** Yes / No
Auto *
DMX
Static
Program
DMX Hi P ON * / OFF
Test Run / Cancel *
Alone *
Master
Slave 1
Slave 2
Slave 3
C Wheel 0-255
Red 0-255
Green 0-255
Blue 0-255
White 0-255
Shutter 0-255
Dimmer 0-255
CTO 0-255
Patt 0-255
Static
Mode
Stand-Alone Personality
Lock
Boot
Master
D Curve
D Speed
Dim clk
Display
Shut-off
No sig fla
Select
Slave
Temp U

- 10 -
Patt Sp 0-255
Patt Fa 0-255
Yes
No
Step 01-30
Capture Yes / Cancel
C Wheel 0-255
Red 0-255
Green 0-255
Blue 0-255
White 0-255
Shutter 0-255
Dimmer 0-255
CTO 0-255
Yes
No
Hold Tim 000-999
Fade Tim 000-999
Prog 2 (See above)
Prog 3 (See above)
Pro 1
Pro 2
Pro 3
Pro 1
Pro 2
Pro 3
Reset All
Reset Reset /Cancel
Enable
Disable *
Red 0-255
Green 0-255
Blue 0-255
White 0-255
Factory No/Yes
Reset xxx Hours
Total xxx Hours
Clear Clear / Cancel
Actual xxx C / F
Max xxx C / F
Reset Max Cancel/Confirm
version x.x.x.x
Fix ID xxxx
Info Stand-Alone
Static
Mode
Service
Temp.
Reset All
Prog 1
P Edit
C Offset
Reset Al
Calibrat
Time
P Play
P Reset

- 11 -
8.DMX protocol
Standard Advanced
Pattern RGBW Compressed
RGBW Pixel Compressed Pixel
Pixel
Dim
Rocket
Mode Fade Type Function Dmx Value
No Function, RGBW Colour mixing 0 - 5
LEE 790-Moroccan Pink 6-10
LEE 157-Pink 11-15
LEE 332-Special Rose Pink 16 - 20
LEE 328-Follies Pink 21 - 25
LEE 345-Fuchsia Pink 26 - 30
LEE 194-Surprise Pink 31 - 35
LEE 181-Congo Blue 36 - 40
LEE 071-Tokyo Blue 41 - 45
LEE 120-Deep Blue 46 - 50
LEE 079-Just Blue 51 - 55
LEE 132-Medium Blue 56 - 60
LEE 200-Double CT Blue 61 - 65
LEE 161-Slate Blue 66 - 70
LEE 201-Full CT Blue 71 - 75
LEE 202-Half CT Blue 76 - 80
LEE 117-Steel Blue 81 - 85
LEE 353-Lighter Blue 86 - 90
LEE 118-Light Blue 91 - 95
LEE 116-Medium Blue Green 96 - 100
LEE 124-Dark Green 101 - 105
LEE 139-Primary Green 106 - 110
LEE 089-Moss Green 111 - 115
LEE 122-Fern Green 116 - 120
LEE 738-JAS Green 121 - 125
LEE 088-Lime Green 126 - 130
LEE 100-Spring Yellow 131 - 135
LEE 104-Deep Amber 136 - 140
LEE 179-Chrome Orange 141 - 145
LEE 105-Orange 146 - 150
LEE 021-Gold Amber 151 - 155
LEE 778-Mellennium Gold 156 - 160
LEE 135-Deep Golden Amber 161 - 165
LEE 164-Flame Red 166 - 170
Coulourwheel rotation forward (fast - slow) 171 - 185
Coulourwheel rotation stop 186 - 190
Coulourwheel rotation backward (fast - slow) 191 - 205
Coulourwheel rotation stop 206 - 210
Fast –211 - 225
Tungsten Simulation 226 - 230
Warm white - 3200K 231 - 235
Neutral white - 4200K 236 - 240
Cold white - 5600K 241 - 245
Cold white - 7200K 246 - 250
Cold white - 8000K 251 - 255
2 2 2 1 1 2 2 Red Red 0-100% 0 - 255
3 Red fine Red fine 0-100% 0 - 255
3 4 3 2 2 3 3 Green Green 0-100% 0 - 255
5 Green fine Green fine 0-100% 0 - 255
4 6 4 3 3 4 4 Blue Blue 0-100% 0 - 255
7 Blue fine Blue fine 0-100% 0 - 255
5 8 5 4 4 5 5 White White 0-100% 0 - 255
9 White fine White fine 0-100% 0 - 255
Shutter Closed 0-15
Random Strobe (slow –16-47
Ramp Up (slow – fast)48-79
Ramp Down (slow – fast)80-111
Ramp UP & down (slow –112-143
Strobe Pause 5s – 1s (slow – fast)144-199
Strobe 1Hz – 20 Hz (slow – fast)200-239
Shutter Open 240-255
7 11 7 6 7 7 66 Dimmer Dimmer 0-100% 0 - 255
Colourwheel rotation effects
Random colours
White hue
1
6
1
10
1
6
1
65
1
6
Colour Wheel
Shutter effects65
12 8 Dimmer fine Dimmer fine 0-100% 0 - 255
8 13 8 9 8 CTO CTO 0 - 255
9 14 10 9 Pattern Pattern 0 - 255
10 15 11 10 Pattern Speed Pattern Speed 0-100% 0 - 255
11 16 11 Pattern Fade Pattern Fade 0-100% 0 - 255
9 68 Pattern 1 Pattern 1 0 - 255

- 12 -
13 1 1 Red 1 Red 1 0-100% 0 - 255
14 2 2 Green 1 Green 1 0-100% 0 - 255
15 3 3 Blue 1 Blue 1 0-100% 0 - 255
16 4 4 White 1 White 1 0-100% 0 - 255
17 5 5 Red 2 Red 2 0-100% 0 - 255
18 6 6 Green 2 Green 2 0-100% 0 - 255
19 7 7 Blue 2 Blue 2 0-100% 0 - 255
Standard Advanced
Pattern RGBW Compressed
RGBW Pixel Compressed Pixel
Pixel
Dim
Rocket
Mode Fade Type Function Dmx Value
10 69 Pattern 1 Speed Pattern 1 Speed 0-100% 0 - 255
11 70 Pattern 1 Fade Pattern 1 Fade 0-100% 0 - 255
12 71 Pattern 1 Red Pattern 1 Red 0-100% 0 - 255
13 72 Pattern 1 Green Pattern 1 Green 0-100% 0 - 255
14 73 Pattern 1 Blue Pattern 1 Blue 0-100% 0 - 255
15 74 Pattern 1 White Pattern 1 White 0-100% 0 - 255
CLOSED 0-3
STROBE SLOW→FAST（1→25 flash/sec） 4-103
OPEN 104-107
PULSATION SLOW→FAST(0.5-25 flash/sec) 108-207
OPEN 208-212
RANDOM STROBE (slow – fast) 213-251
Shutter Open 252-255
17 76 Pattern 1 Dimmer Pattern 1 Dimmer 0-100% 0 - 255
18 77 Pattern 2 Pattern 2 0 - 255
19 78 Pattern 2 Speed Pattern 2 Speed 0-100% 0 - 255
20 79 Pattern 2 Fade Pattern 2 Fade 0-100% 0 - 255
21 80 Pattern 2 Red Pattern 2 Red 0-100% 0 - 255
22 81 Pattern 2 Green Pattern 2 Green 0-100% 0 - 255
23 82 Pattern 2 Blue Pattern 2 Blue 0-100% 0 - 255
24 83 Pattern 2 White Pattern 2 White 0-100% 0 - 255
CLOSED 0-3
STROBE SLOW→FAST(1→25 flash/sec) 4-103
OPEN 104-107
PULSATION SLOW→FAST(0.5-25 flash/sec) 108-207
OPEN 208-212
RANDOM STROBE (slow – fast) 213-251
Shutter Open 252-255
26 85 Pattern 2 Dimmer Pattern 2 Dimmer 0-100% 0 - 255
Reserved 0 - 55
Dimmer Speed: Smooth 56 - 60
Dimmer Speed: Fast 61 - 65
Reserved 66 - 70
Dimmer Curve: Linear 71 - 75
Dimmer Curve: Threatrical 76 - 80
Dimmer Curve: Sqaure Law 81 - 85
Dimmer Curve: Inverse Sqaure Law 86 - 90
Reserved 91 - 95
No DMX: Hold 96 - 100
No DMX: Shutter Closed 101 - 105
No DMX: Play Program 1 106 - 110
Reserved 111 - 115
Display Backlight: On 116 - 120
Display Backlight: Off 121 - 125
Reserved 126 - 135
DMX Mode: Standard 136 - 140
DMX Mode: Advanced 141 - 145
DMX Mode: Pattern 146 - 150
DMX Mode: Pixel 151 - 155
DMX Mode: Compressed Pixel 156 - 160
DMX Mode: Pixel Dim 161 - 165
DMX Mode: Rocket Mode 166 - 170
Reserved 171 - 180
Fixture Reset 181 - 185
Factory default(except DMX Address & Mode) 186 - 190
Reserved 191 - 200
PWM Rate: 600 Hz 201 - 205
PWM Rate: 1200 Hz 206 - 210
PWM Rate: 2000 Hz 211 - 215
PWM Rate: 2400 Hz 216 - 220
PWM Rate: 6000 Hz 221 - 225
Reserved 226 - 230
Boot Mode: Auto 231 - 235
Boot Mode: DMX 236 - 240
Boot Mode: Program Play 241 - 245
Boot Mode: Static 246 - 250
Reserved 251 - 255
12 17 27
16
25
12 12 67
Pattern 1 Shutter
Pattern 2 Shutter
Control
75
84

- 13 -
20 8 8 White 2 White 2 0-100% 0 - 255
21 9 9 Red 3 Red 3 0-100% 0 - 255
22 10 10 Green 3 Green 3 0-100% 0 - 255
23 11 11 Blue 3 Blue 3 0-100% 0 - 255
24 12 12 White 3 White 3 0-100% 0 - 255
25 13 13 Red 4 Red 4 0-100% 0 - 255
26 14 14 Green 4 Green 4 0-100% 0 - 255
27 15 15 Blue 4 Blue 4 0-100% 0 - 255
28 16 16 White 4 White 4 0-100% 0 - 255
29 17 17 Red 5 Red 5 0-100% 0 - 255
30 18 18 Green 5 Green 5 0-100% 0 - 255
31 19 19 Blue 5 Blue 5 0-100% 0 - 255
32 20 20 White 5 White 5 0-100% 0 - 255
33 21 21 Red 6 Red 6 0-100% 0 - 255
34 22 22 Green 6 Green 6 0-100% 0 - 255
35 23 23 Blue 6 Blue 6 0-100% 0 - 255
36 24 24 White 6 White 6 0-100% 0 - 255
37 25 25 Red 7 Red 7 0-100% 0 - 255
38 26 26 Green 7 Green 7 0-100% 0 - 255
39 27 27 Blue 7 Blue 7 0-100% 0 - 255
40 28 28 White 7 White 7 0-100% 0 - 255
41 29 29 Red 8 Red 8 0-100% 0 - 255
42 30 30 Green 8 Green 8 0-100% 0 - 255
43 31 31 Blue 8 Blue 8 0-100% 0 - 255
44 32 32 White 8 White 8 0-100% 0 - 255
45 33 33 Red 9 Red 9 0-100% 0 - 255
46 34 34 Green 9 Green 9 0-100% 0 - 255
47 35 35 Blue 9 Blue 9 0-100% 0 - 255
48 36 36 White 9 White 9 0-100% 0 - 255
49 37 37 Red 10 Red 10 0-100% 0 - 255
50 38 38 Green 10 Green 10 0-100% 0 - 255
51 39 39 Blue 10 Blue 10 0-100% 0 - 255
52 40 40 White 10 White 10 0-100% 0 - 255
53 41 41 Red 11 Red 11 0-100% 0 - 255
54 42 42 Green 11 Green 11 0-100% 0 - 255
55 43 43 Blue 11 Blue 11 0-100% 0 - 255
56 44 44 White 11 White 11 0-100% 0 - 255
57 45 45 Red 12 Red 12 0-100% 0 - 255
58 46 46 Green 12 Green 12 0-100% 0 - 255
59 47 47 Blue 12 Blue 12 0-100% 0 - 255
60 48 48 White 12 White 12 0-100% 0 - 255
61 49 49 Red 13 Red 13 0-100% 0 - 255
62 50 50 Green 13 Green 13 0-100% 0 - 255
63 51 51 Blue 13 Blue 13 0-100% 0 - 255
64 52 52 White 13 White 13 0-100% 0 - 255
65 53 53 Red 14 Red 14 0-100% 0 - 255
66 54 54 Green 14 Green 14 0-100% 0 - 255
67 55 55 Blue 14 Blue 14 0-100% 0 - 255
68 56 56 White 14 White 14 0-100% 0 - 255
69 57 57 Red 15 Red 15 0-100% 0 - 255
70 58 58 Green 15 Green 15 0-100% 0 - 255
71 59 59 Blue 15 Blue 15 0-100% 0 - 255
72 60 60 White 15 White 15 0-100% 0 - 255
73 61 61 Red 16 Red 16 0-100% 0 - 255
74 62 62 Green 16 Green 16 0-100% 0 - 255
75 63 63 Blue 16 Blue 16 0-100% 0 - 255
76 64 64 White 16 White 16 0-100% 0 - 255
13 Dimmer 1 Dimmer 1 0-100% 0 - 255
14 Dimmer 2 Dimmer 2 0-100% 0 - 255
15 Dimmer 3 Dimmer 3 0-100% 0 - 255
16 Dimmer 4 Dimmer 4 0-100% 0 - 255
17 Dimmer 5 Dimmer 5 0-100% 0 - 255
18 Dimmer 6 Dimmer 6 0-100% 0 - 255
19 Dimmer 7 Dimmer 7 0-100% 0 - 255
20 Dimmer 8 Dimmer 8 0-100% 0 - 255
21 Dimmer 9 Dimmer 9 0-100% 0 - 255
22 Dimmer 10 Dimmer 10 0-100% 0 - 255
23 Dimmer 11 Dimmer 11 0-100% 0 - 255
24 Dimmer 12 Dimmer 12 0-100% 0 - 255
25 Dimmer 13 Dimmer 13 0-100% 0 - 255
26 Dimmer 14 Dimmer 14 0-100% 0 - 255
27 Dimmer 15 Dimmer 15 0-100% 0 - 255
28 Dimmer 16 Dimmer 16 0-100% 0 - 255
Standard Advanced
Pattern RGBW Compressed
RGBW Pixel Compressed Pixel
Pixel
Dim
Rocket
Mode Fade Type Function Dmx Value

- 14 -
9.Maintance and cleaning
DANGER:Disconnect from the mains before starting any maintenance work.
Ballast
Please change timely when each pin is getting yellow.
Be sure to maintain the device every 2 months,and make sure that all parts of the ballast,such as,scre-
ws,terminals,are locked well to ensure performance.Neglecting of maintenance may lead to failure of
devices.
Lamp
Turn off the lamp first to better protect the device when the fixture is turned off. Turn off the power after
running for at least 5 minutes
Don't touch the bulb with your hands.Once contacting with your hands,scrub with alcohol and then dry
with linen.
When the light is on, the bulb runs at high pressure,so there is a risk of broken.It is related to the duration
of using,temperature and unreasonable operation.Therefore, please do not use lamp over the life span.
The using of lamp should not exceed hours,otherwise it can damage device.Check the running
time of the fixure regularly.When the lamp is used around 10000 hours,We strongly recommend that you
change the lamp.After replacing it,the used time of lamp can be removed and reset.
Avoid operating in dirty and dusty environment, clean and maintain lamps regularly. Wipe the outside of
the lens at least every 20 days. Wipe the internal fan at least every 30 days
It is absolutely essential that the fixture is kept clean and that dust,dirt and smoke fluid residues must not
buildup on or within the fixture. Otherwise, the fixtures light-output will be significantly reduced. Regular
cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably
through out its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended,
under no circum stances should alcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues,reduc-
ing the light-output very quickly.The cooling-fans should be cleaned monthly.
The gobos may be cleaned with a soft brush,The interior of the fixture should be cleaned at least annua-
lly usinga vacuum-cleaner or an air-jet.
There are no serviceable parts inside the device except for the lamp and the fuse.
10000
Please disconnect the power supply before replacing the fuse and bulb. When replacing them, adopt the
same mode.

- 15 -
10.Electric equipment specification
10.1 Electrical paramters
SOURCE:
POWER:260
VOLTAGE:
RGBW 16 LED-15W 4IN1
W
AC100-240V 50/60HZ
Color temperature：6500K(W)
10.2 Weight and dimensions
Dimensions：
NET WEIGHT:7.5Kg
Dimensions
WEIGHT
1009X153X181
Carton package
Carton package
mm
( ): 11Kg
（ ）:1090X300X183mm
10.3 Channel Characteristics
2.Demme r: limear dimme r.
3.Shutter: electronic shutter, random strobe.
4.LED individual control, preseting automatical temp erature control system.
1.Channel:12、17、27、4、6、76、64、28、85 DMX -512.
10.4 Menu Function
2.Display the time using of lighting feature and lamp as well as the times of turning on for lamp.
3.
4.Software upgrade function.
1.
After the DMX signal is disconnected, the display will be bright and dark.
Each DMX Value displayable.

- 16 -
11.Electronic drawing
Note: The above contents for reference only and is subject to change without prior notice, please
take specification you have on hand and our company reserves the final right of interpretation.
-
+
DC12V
N
L
G
AC220V
OUTPUT
-
+
DC12V
N
L
G
AC220V
OUTPUT
2
13
46
57
8
911
10 12 14
13 14 15 16
16
8
6
4
2
22
1345
4
628
6823
24
NTC
721 22 22 910
10
12 11 21
12
14 13
14 23
15
16
24
12
10
AC220V
DMX DMX
NTC
16