Jonti-Craft Young time 7104YT User manual

DHCJW –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 1 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
WARNING:
CHOKING HAZARD/SHARP POINTS- Assembly
hardware contains small parts and components
with sharp points. Adult assembly required.
Attention: This unit must be attached to a wall to
prevent tipping over!!
Hardware Illustrations
Not Actual Size
Tools Required:
-4mm Hex Wrench, (Provided)
-Medium Phillips Screwdriver
Instructions for:
7104YT Coat Locker, Wall, 10-Section
Hardware Package HCJW
Qty. Description
(1) XAUS 4mm Hex Wrench
(12)XAUR 2" Decorative Screw
(3) XCPT #8 X 0-7/8” washerhead Screw
(10)XBTX #6 X 0-5/8" Trusshead Screw
(3) XAFH #8 X 3” Drywall Screw
(2) XAEB #6 X 1-1/4” Drywall Screw
(5) XCLX Nylon Coat Hook
Parts:

DHCJW –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 2 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
Assembly Instructions:
1. Place Hook Rail-Gon flat surface and install 5-XCLX Coat Hooks with 10-XBTX Screws using
Phillips Screwdriver. Note location of rounded edge in respect to hook placement. Set aside for
installation later.
2. Install Top-C, Bottom-A, and Shelf-Bto LH Side-Dby aligning dowels. Ensure back grooves all
align and rounded edge of shelf is down. Secure with 6-XAUR Decorative Screws with 4mm Hex
Wrench provided.
3. Install RH-Side-Eby aligning dowels. Ensure back groove is up and aligns with other grooves.
Loosely install with 6-XAUR Decorative Screws with 4mm Hex Wrench provided.

DHCJW –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 3 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
4. Drop in 8-Hardboard Dividers-Jinto groves with rounded edge down.
5. Insert 2-Backs-I by inserting into LH Side groove on one end, bowing into other groove on
opposite end, and sliding into full length grooves on Top and Bottom.
6. Install Hanging Bracket-F and Hook Rail-G by aligning dowels. Ensure Backs (previously installed)
are seated into Top, Bottom, and Side grooves. Note location and orientation of mitred edge of
Hanging Bracket and hooks on Hook Rail. Tighten 6-XAUR Decorative Screws previously installed.

DHCJW –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 4 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
7. Locate predrilled holes in middle shelf and install 3-XCPT Washer head Screw with Phillips Driver.
8. Instructions for Wall Mounting:
a) After selecting the location and mounting height on the wall, determine the positioning of the
wall studs and attach the Wall Mounting Bracket-Hto the wall studs using included 3-XAFH 3”
Drywall Screws (note orientation of mitre of wall bracket in diagram below).
NOTE: Wall mounting bracket must be secured to at least two wall studs.
b) Lift the Wall Locker up into position above the wall mounted bracket and allow the unit to slide
down into position on the wall mounted bracket.
c) Finish securing the unit by inserting 2-XAEB 1-1/4” Drywall Screws through the back of the
unit and into the wall mounting bracket secured to the wall. This step will ensure that the unit
will not lift off the wall mounted bracket.
9. If you experience any difficulties when assembling this product, please contact the Jonti-Craft
Customer Relations Team at [phone] or [e-mail]. All other requests for
assistance must be directed to your Jonti-Craft Dealer.
General Care & Maintenance Guidelines: www.jonti-craft.com/generalcare