JR ProPo PDX16 User manual

■PDX16(This product)
■E-Switch Adapter
■Accessory
■Serial Bus Adapter (2)
■8chSignal Cables(2)
■Manual
OPERATION
MANUAL
man_pdx16_en
Failure to follow these instructions can cause
serious injury or death to the user or others.
■By using high capacity batteries, it enables servos to be powered reliably.
■
Integrated electric switch for added safety.
■ Capable to use for any other radio manufacturer systems, as it
only by-passes the signals.
■ For serial bus connection, Separate sold Bus adapter shall ease
the connection to the unit.
■Product name: PDX 16
■Dimensions: 2.36 x 3.54 x 0.59 inch / 60x90x15 mm
■Weight: 3.44oz/ 97.5 gram
■Operating voltage: under 12.6 V
■Connection Port: 16 ports
DANGER
●Do not use this product in the rain as water may cause electronic devices to malfunction.
●This product carries a risk of injury due to heat, fire and electric shock.
●Never disassemble or modify this product.
●Only use the correct input voltage.
●Be sure to check the polarity when you input the battery connector to this product.
●Reversing connection/polarity may damage this product.
●Be sure to check the battery capacity upon operating this product, if the battery capacity
is under the operational voltage, this product may not function properly.
●Please check that all screws are securely tightened on product.
●Do not use this product if there is even slight damage to the wire harness, connectors,
or other assemblies.
●Properly secure excess wires in place to avoid excess movement and damage.
Thank you for purchasing this product.
To allow correct and safe use of this product,
please read this operation manual
FEATURES
SPECIFICATION
CONTENTS
Konishi Mokei Co., Ltd. (RC DEPOT)
1-3-17 Izumi, Noda-City, Chiba-Pref. 270-0239 JAPAN
For U.S.A.: [email protected] (Ph: 217-369-2854)
For Australia: [email protected] (Ph:07-3879-6692)
For other overseas Countries: [email protected]
▲ ▲
T B
TOP▶
BOTTOM▶
BOTTOM▶
TOP▶
XT60 DEANS
There are two choice
of the battery conne-
ctor available as
Deans or XT60
※There is no polarity on switch plug.
Electric Switch
−)
Negative terminal
＋
)Positive terminal
−)Negative line (Black)
※ Besuretoinserttheconnector
harnessincorrectdirection
Signal Output Ports
＃1−＃8
Signal Output Ports
＃9−＃16
Signal input Ports
Receiver
Battery
such as
Li-Po 3S
＋)Positive line (RED)
−)
Negative terminal
＋
)Positive terminal
Signal terminal
Thisproductshallfeedtheexactinputvoltagetotheservooperating
voltage.Besuretousespecifiedvoltageontheservo.
配置図 SERVO OUTPUT PORT
Input signal is directly sent unre-
gulated to the output terminals.
■PWM Input => PWM Output
■Bus Input => Bus Output
Note: Under the Serial connection
use, never connect PWM servos.
Quick feature on this product.
Be sure to check the polarity before
actual insertion of the connectors.
◆Using a high capacity , the PDX16 by-passes the
receiver, delivering maximum reliable power directly
to the servos. The PDX16 safely delivers the correct
voltage requirements to the receiver. The receiver now
delivers only the control signals to the servos through
the PDX16, not the power.
◆PDX16 works with both PWM and Serial Bus
technology and is compatible with most other radio
manufacturer’ s systems.
◆PDX16 is compatible with super hi voltage servos
(12v)3S Li-Po(12.6v) packs can be used with 12v super
high voltage servos.

Be sure to insert the negative terminal
of the connector facing towards
the bottom side of unit.
−
terminal
＋
terminal
Signal terminal
Serial bus adapter
Serial Bus channel shall
be decided by the
program on the
transmitter
PWM servo require
to use separate sold
PWM converter on
XBus serial connection.
Input XBus signal shall
output to every servo
out port.
XBus servo shall activate depending
on the designatedID channels.
Serial Bus connection by using
separate sold Bus adapter
This product shall feed the exact input voltage to the servo operating voltage.
Be sure to use the specified voltage on the servos.
RECEIVER
【1 】
XBUS
OUTPUT
RECEIVER
【2 】
XBUS
OUTPUT
Receiver
【2】
Bus signal
output to
the Port 9-16
Receiver
【1】
Bus signal
output to
the Port 1-8
Input PWM signal shall
output to the same
number of servo
output port.
PWM Connection by using the
8channel signal harness
Brown
Red
Orange
Yellow
Green
Blue
Purple
Gray
White
Black
Color of harness
RX ch
−
+
1ch
2ch
3ch
4ch
5ch
6ch
7ch
8ch
Connection list in
8ch receiver and
8ch PWM signal harness
16
14
12
10
15
13
11
9
1
3
5
7
2
4
6
8
CONNECTION
DIAGRAM-1
CONNECTION
DIAGRAM-2
8ch
RECEIVER
【2 】
PWM
OUTPUT
Single battery connection
shall supply power to
both receiver connector
terminals.
Be sure to check the polarity before
actual insertion of the connectors.
Be sure to check the polarity before
actual insertion of the connectors.
*Note on Current JR servo
harness: White wire is the signal
wire, center wire is Positive and
the other side is negative.
Single battery connection
shall supply power to
both receiver connector
terminals.

This product shall feed the exact input voltage to the servo operating voltage.
Be sure to use the specified voltage on the servos.
Serial bus adapter
Serial Bus channel shall
be decided by the
program on the
transmitter
PWM servo require
to use separate sold
PWM converter on
XBus serial connection.
XBus servo shall activate depending
on the designatedID channels.
Diagram showing the connection of XBus receiver and Barvarian Demon's "CORTEX PRO"
Insert Lead Harness "B" connector to CORTEX PRO on port "A and "B" from XBus receivers.
Note: Port "B" is the primary port on single serial Bus connection.
Insert the Serial Bus adapter's connector to PDX16 from CORTEX PRO terminal 5 and 6.
PDX16 shall output XBus Serial signals on all the servo output port.
Note: Failsafe function must be set at CORTEX PRO
RECEIVER
【1 】
XBUS
OUTPUT
RECEIVER
【2 】
XBUS
OUTPUT
Bus signal
output to
the Port 9-16
Bus signal
output to
the Port 1-8
CONNECTIONDIAGRAM-3 Be sure to check the polarity before
actual insertion of the connectors.
Single battery connection
shall supply power to
both receiver connector
terminals.
Negative terminal (
−)
Positive terminal (
＋
)
Signal terminal
6 5 4321DCB A
Serial bus adapter 2Serial bus adapter 1
−
terminal
＋
terminal
Signal terminal
※ForfurtherdetailonCORTEXPRO,
refertotheirownmanualontheir
website.
https://www.bavariandemon.com/
* Be sure to check the
polarity on connector.
* Be sure to check the
polarity on connector.
* Port "B" is the primary
serial Bus port