JuicePro ALI-VJP-W2 Manual

For Customer Care visit www.juice-pro.com.au
1300 764 325
Alibaba Imports Pty Ltd
c/- Perks & Associates
180 Greenhill Road
Parkside SA 5063 Australia
www.juice-pro.com.au
Congratulations on your purchase
of a JuicePro Cold Press Juicer
Note: Please read through the instructions carefully before using or installing the product and ensure that the
manual is kept in a safe place for future reference.
The system must be properly installed and located in accordance with the installation instructions before it is used.
Electrical Requirements:
Australia / New Zealand 240V / 230V 50Hz
Due to manufacturing alterations product may
vary slightly from that is pictured.
N 31230

INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU 1
OPERATION CONDITIONS & SAFETY PRECAUTIONS
• All components need to be installed in accordance with the
user manual instructions for correct per formance of unit.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• To protect against risk of electrical shock, do not put the main
body (motor) in water or any other liquid.
• Unplug from outlet when not in use, before assembling or
taking off parts and before cleaning.
• Avoid contact of moving parts.
• Do not use attachments not recommended or sold by the
manufacturer as it may lead to fire, electric shock or injury.
• Always ensure you switch the juicer to the off position and the
motor has stopped completely before disassembling.
• Do not put your fingers or foreign objects into the juicer while
it is in operation. If food becomes lodged in the inlet use the
plunger to push it down, or use the reverse button on the
machine to dislodge. If this is not possible turn juicer off and
wait for motor to completely stop before disassembling juicer to
remove food.
• Do not use outdoors.
• Do not use appliance for other than intended purpose.
• Lift appliance with the handle only.
• Do not put any parts into the dishwasher,
NOT dishwasher safe.
• Do not use appliance continuously for more than 15 minutes
as overheating will automatically shut down the unit. This unit
is for household use only and warranty is not extended to units
used for commercial purposes.
• Do not use the appliance to juice hard materials, including pips,
ice, frozen fruit, large seeds.

2INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU
INSTALLATION & OPERATING INSTRUCTIONS
A. Component identification & content check list:
ALI-VJP-W2 / ALI-VJP-R2 - JuicePro Cold Press Juicer
Ref Description Qty
Main Components
A Hopper 1
B Squeezing Screw 1
C Strainer (yellow) - less pulp 1
D Spinning Brush 1
E Bowl 1
F Base 1
G Cleaning Brush 1
H Pusher 1
I Container 2
Note: Do not pre-operate before inputting materials or do not
operate with an empty bowl.
Important: The Base, Bowl and Hopper must be correctly
aligned for the machine to operate correctly. (See Fig 1).
Fig 1
A
B
C
D
E
Pulp
outlet Juice outlet
HI
F
G

INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU 3
B. Assembly Instructions:
Important: Prior to Assembling the Juicer please check this point:
At the base of the bowl there is a rubber stopper. When in place
the stopper ensures all of the juice only exits via the juice outlet.
Before juicing always ensure that the rubber stopper is firmly in
place. (See Fig 2).
1. Assemble the bowl on the base
(See Fig 3).
A. Make sure the bowl is sitting
securely on the base.
2. The strainer supplied is a fine strainer and will reduce the
amount of pulp in your juice.
A. Insert the strainer into the spinning brush.
B. Align the dot on the strainer
with the dot on the bowl and
insert strainer + spinning
brush into the bowl. When the
dots are correctly aligned the
strainer + spinning brush will
lock in place. (See Fig 4).
3. Insert the squeezing screw
into the strainer and turn
until it drops into position.
(See Fig 5).
Fig 2
Rubber stopper
Fig 3
A
Bowl
Fig 5
Squeezing
screw
Fig 4
Dot on
strainer
Strainer Spinning
brush
Dot on the
bowl

4INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU
4. Assemble the hopper onto
the bowl. (See Fig 6).
A. Align the small arrow on the
hopper with the dot on the bowl.
B. Twist the hopper clockwise
so that the plastic tab on the
hopper is in line with the on/off
switch and handle. (See Fig 7).
Note: The small arrow from part
4.A will no longer be aligned with
the dot once the hopper is locked
to the close position. (See Fig 7).
C. Operating Instructions:
Warning:
• Do not operate the juicer with wet hands as it may cause an
electric shock.
• Do not operate the juicer prior to imputing juicing materials.
• Do not operate for more than 15 minutes at one time.
Important:
To protect the motor and provide you with a long lasting machine
the Juice Pro has an auto shut down feature. If the components
are not aligned or installed correctly, the motor overheats due to
extended juicing or the strainer becomes clogged the machine will
automatically shut down. This is normal and prevents damage to
your Juice Pro.
If this happens switch the machine off. Check components are
correctly installed and that there is no food caught in the strainer.
Wait 5 minutes for the motor to cool then recommence normal
operation.
Fig 7
Fig 6
dot on bowl
hopper arrow on
hopper
A.
B.

INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU 5
1. Plug in the juicer.
2. Place a container below the juice outlet and a container below
the pulp outlet.
3. The juicer power button (located at the top of the handle)
has 3 positions.
A. ON - This starts the motor and juicing process.
B. OFF - Is the central position of the button. It switches off
the appliance.
C. REV - Is reverse. Only use this function when something is
stuck in the juicer and it needs to be unclogged.
4. Prepare the material you wish to juice. The Juice Pro is
designed to juice many different materials. The preparation for
each material will differ, the below points are a guide. Please
read page 8 and 9. Getting started with your Juice Pro for
further tips on Juicing.
• Ensure juice material is cut into small portions for optimal juice
extraction. Each portion should easily fall down the hopper
chute without the need for force.
• Remove any large pips or seeds. This includes stones from
stone fruits and peel from citrus fruits.
• Always pre-wash food before juicing.
5. Switch the power button to ‘ON’. Insert the food into
the hopper.
• Insert food slowly one piece at a time and allow juicer
time to work.
• Do not overstuff the hopper
or force food in. The pusher
is only to be used if food
becomes stuck. (See Fig 8).
6. When you are finished switch
the power button to ‘OFF’.
Note: If you are making multiple
juices in one session to avoid
cross over of flavours, pour
water into the hopper between
drinks to clean the unit. Capture
rinsing water in a separate bowl
so as not to dilute your juice.
Depending on the material being
juiced you may need to clear
some pulp from the strainer.
ON
REV
OFF
A
B
C
Fig 8
Insert pieces
Pusher

6INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU
D. If the machine becomes clogged and inoperable:
1. Turn the machine off and press the reverse button for a few
seconds then try operating again. Note: The reverse button
works with a ‘pulse’ motion.
2. If the reverse button does not work turn off the machine
and switch off at the power point. Disassemble the unit to
dislodge any material then reassemble as per the instructions
and try again.
E. How to disassemble and clean the unit:
1. Switch off the unit.
2. Twist the hopper anti clockwise then lift off.
(See Fig 9). Lift the bowl straight up to remove from the base.
3. Disassemble the parts from the bowl in the order shown by the
diagram. (See Fig 10).
4. Use the brush to clean all of these parts thoroughly in warm
soapy water then dry thoroughly. Ensure the pulp outlet on
the bowl is clear (the end of the cleaning brush is designed to
clear trapped material from the pulp outlet). Unplug the rubber
stopper for easier access to the pulp outlet.
Caution: Before juicing ensure the rubber stopper is firmly in place.
(See Fig 2, Page 3).
5. Use a damp cloth to wipe down the base of the unit.
Cleaning Tips:
• Periodically remove the silicone brushes from the spinning
brush and clean thoroughly before reassembling.
• Thoroughly clean immediately after each use to minimize staining.
• Pull out the rubber stopper on the base of the bowl to clean
bowl effectively. Always ensure the rubber stopper is re-inserted
prior to juicing otherwise it may cause a leak.
• Do not use harsh abrasives or chemicals to clean the juicer.
• Do not clean in the dishwasher.
1 2 3 4
Fig 10
Fig 9

INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU 7
TROUBLE SHOOTING
BEFORE YOU CALL FOR SERVICE PLEASE REVIEW THE TROUBLE SHOOTING TIPS FIRST.
Problem Possible Causes What To Do
No power to juicer.
Juicer not plugged in. Check the juicer is plugged in.
Incorrect assembly. Reassemble the juicer according to the instructions.
Motor has stopped.
Bowl has been overfilled with material. Press the reverse power button to try and clear the clog.
May need to be try this a few times.
Overuse has caused the motor to shut
down as a precaution to overheating. Switch off and let the motor cool before using again.
Leaking from beneath the
bowl.
Rubber plug on base of bowl not correctly
inserted. Rubber plug on base of bowl not correctly inserted.
A small amount of residual juice is normal. It is normal to find a small amount of juice, clean from
the appliance with damp cloth.
Stain on the bowl, strainer,
spinning brush. Natural colour from juicing materials.
This is perfectly normal. To reduce discolouration
ensure you rinse and clean the appliance immediately
after use.
Squeaking noise during
operation. Juicing noise from squeezing screw. This is perfectly normal. Ensure you do not overload
the juicer.
Damage to the strainer. Frozen foods, ice, pips, seeds, unknown
substance or too much material in the bowl.
Ensure you read the instructions carefully on the correct
use of the juicer. Do not overfill the juicer.
Spare parts available, visit www.juice-pro.com.au

8INSTALLATION AND OPERATING INSTRUCTIONS | WWW.JUICE-PRO.COM.AU
Material Size and Juicing Speed
The size of the material and the speed at which you feed it
into your juicer is very important in achieving good results.
To familiarise yourself with the process we recommend you
start with easy to juice materials such as citrus fruits.
(Remember to always remove the peel first!).
Cut the material into small portions that will easily fall down
the hopper chute without being forced. The harder the fruit or
vegetable type the smaller the portion should be, for example
carrot and beetroot should be cut into 2cm segments.
Feed the material into the hopper, generally a segment at a time.
Allow the juicer time to work and process the material before
adding more. Gradually increase the feeding rate, through trial and
error you will soon familiarise yourself with the right material size
and feeding speed.
You will find that harder materials like beetroot may need longer to
process than softer materials like citrus fruit.
Time to Experiment
Once you are confident in using your juicer get creative and
experiment, who knows you may just invent a new flavour!
Here are a few ideas to get you started:
• You can try all sorts of fruit / vegetable combinations - don’t
forget to try adding beetroot, cucumber, broccoli, berries or
tomatoes to name a few.
• Juice leafy greens such as spinach or wheat grass.
(See page 9 for juicing for leafy greens.)
• Try adding fennel for an aniseed flavour.
• To get a nice kick add a small amount of Ginger or Garlic.
• Make an almond or soy milk. (See page 9 for Soy & Nut milks.)
Getting started with your Juice Pro
Juicing is a fun and easy way to enjoy fruit and vegetables.
The different taste combinations are endless and only limited by your imagination!
The Juice Pro Cold Press Juicer is not a conventional juicer and therefore cannot be used in the same way.
Take the time to get to know the mechanics of your juicer and how it works best, to do this we suggest you
start with easy to juice items and work up to experimenting with different flavour combinations.