Jumbo SmartBox SF-1315 User manual

Flat
* M connectors for extention only
4. Insert rubber stoppers for 750 mm floor
Socket cap
panel x3
panels by hand into horizontal tubes.
panel x10
DC
tube 750 mm are facing inward.
R
head
M
L connector x4
*Make sure that screw holes of horizontal
*Make sure that the concave holes on both
screw
Socket cap screw X8
* Fix the R connector to the left side and M connector to
* L connector for left side
R
the frame B.
3. Press one side corner into the frame and then others,
Vertical frame x4
1. * Fix the L connector to the inside of frame A with a screw.
L
stopper x8
375 mm Steel
screw
Socket cap
B
2. Attach the horizontal tube to the connector and
750 mm Steel
then rotate it by 90 degrees by hand.
A
screw
MR
the right side of frame B with a flat screw.
Causion:
R connector x8
pat the panel corner in one by one.
Rubber
* R connector for right side
M4 Hex screwdriver X1
sides of the horizontal tube are facing up.
R connector x4
M connector x8
375 mm Horizontal tube x8
Assembly Instructions
750 mm Horizontal tube x4
Flat head screw X8
Flat
head
screw
Causion:
* Fix the connectors to the frame C in the same order as
* Fix the R connector to the inside of frame D with a screw.
Model No.: SF-1315
Modellnummer: SF-1315
Montageanleitung
Vertikaler Rahmen x4 L-Verbindungsstecker x4 M-Verbindungsstecker x8
R-Verbindungsstecker x8 R-Verbindungsstecker x4 M4 Innensechskantschlüs- sel X1 Gummi-Stopfen x8
750 mm Stahlblech x3 375 mm Stahlblech x10 Flachkopfschraube x8 Innensechskantschraube x8 375 mm horizontales Rohr x8
750 mm horizontales Rohr x4
Innen-
sechskant-
schraube Innensechs-
kantschraube
Flach-
kopf-
schraube
Flach-
kopf-
schraube
1. * Befestigen Sie den L-Verbindungsstecker mit einer Schraube an der
Innenseite von Rahmen A.
* Befestigen Sie den R-Verbindungsstecker an der linken Seite und
den M-Verbindungsstecker an der rechten Seite von Rahmen B mit
hilfe einer Flachkopfschraube.
* Befestigen Sie die Verbindungsstecker am Rahmen C in der glei-
chen Reihenfolge wie am Rahmen B.
*Befestigen Sie den R-Verbindungsstecker mit einer Schraube an der
Innenseite von Rahmen D.
Achtung: * L-Verbindungsstück für linke Seite
* R-Verbindungsstecker für die rechte Seite
* M-Verbindungsstecker nur für Erweiterung
2. Befestigen Sie das horizontale Rohr an den Verbindungsste-
ckern und drehen Sie es dann von Hand um 90 Grad.
Achtung: * Stellen Sie sicher, dass die konkaven Löcher an beiden Seiten des
horizontalen Rohrs nach oben zeigen.
* Stellen Sie sicher, dass die Schraubbohrungen des horizontalen
750-mm-Rohrs nach innen weisen.
3. Drücken Sie zuerst eines der Seitenbleche in den Rahmen und dann
die anderen; klopfen Sie die Ecken der Bleche nacheinander fest.
4. Gummistopfen für 750 mm Bodenblech von Hand in horizontale
Öffnungen einlegen.

Flat
* M connectors for extention only
4. Insert rubber stoppers for 750 mm floor
Socket cap
panel x3
panels by hand into horizontal tubes.
panel x10
DC
tube 750 mm are facing inward.
R
head
M
L connector x4
*Make sure that screw holes of horizontal
*Make sure that the concave holes on both
screw
Socket cap screw X8
* Fix the R connector to the left side and M connector to
* L connector for left side
R
the frame B.
3. Press one side corner into the frame and then others,
Vertical frame x4
1. * Fix the L connector to the inside of frame A with a screw.
L
stopper x8
375 mm Steel
screw
Socket cap
B
2. Attach the horizontal tube to the connector and
750 mm Steel
then rotate it by 90 degrees by hand.
A
screw
MR
the right side of frame B with a flat screw.
Causion:
R connector x8
pat the panel corner in one by one.
Rubber
* R connector for right side
M4 Hex screwdriver X1
sides of the horizontal tube are facing up.
R connector x4
M connector x8
375 mm Horizontal tube x8
Assembly Instructions
750 mm Horizontal tube x4
Flat head screw X8
Flat
head
screw
Causion:
* Fix the connectors to the frame C in the same order as
* Fix the R connector to the inside of frame D with a screw.
Model No.: SF-1315
Modèle n° : SF-1315
Instructions d‘assemblage
Cadre vertical x4 Connecteur G x4 Connecteur M x8
Connecteur D x8 Connecteur D x4 Clé allen hexagonale M4 x1 Bouchon de caoutchouc x8
Panneau d‘acier
750 mm x3
Panneau d‘acier
375 mm x10 Vis à tête plate x8 Vis à tête cylindrique x8 Tube horizontal 375 mm x8 Tube horizontal 750 mm x4
Vis à tête
cylindrique Vis à tête
cylindrique
Vis à
tête plate
Vis à
tête plate
1. * Fixez le connecteur G à l‘intérieur du cadre A avec une vis.
* Fixez le connecteur D sur le côté gauche et le connecteur M sur le
côté droit du cadre B à l’aide d’une vis plate.
* Fixez les connecteurs au cadre C dans le même ordre que pour le
cadre B.
* Fixez le connecteur D à l‘intérieur du cadre D avec une vis.
Attention: * Le connecteur G est destiné au côté gauche
* Le connecteur D est destiné au côté droit
* Les connecteurs M sont réservés aux extensions
2. Fixez le tube horizontal au connecteur, puis faites-le pivoter de
90 degrés à la main.
Attention: * Assurez-vous que les trous concaves des deux côtés du tube
horizontal soient bien orientés vers le haut.
* Assurez-vous que les trous des vis sur le tube horizontal de
750 mm soient bien orientés vers l‘intérieur.
3. Enfoncez l‘un des coins dans le cadre, puis les autres coins, et
enfoncez bien chaque coin du panneau un par un.
4. Insérez à la main les bouchons de caoutchouc des panneaux
750 mm dans les tubes horizontaux.
GDD D

Flat
* M connectors for extention only
4. Insert rubber stoppers for 750 mm floor
Socket cap
panel x3
panels by hand into horizontal tubes.
panel x10
DC
tube 750 mm are facing inward.
R
head
M
L connector x4
*Make sure that screw holes of horizontal
*Make sure that the concave holes on both
screw
Socket cap screw X8
* Fix the R connector to the left side and M connector to
* L connector for left side
R
the frame B.
3. Press one side corner into the frame and then others,
Vertical frame x4
1. * Fix the L connector to the inside of frame A with a screw.
L
stopper x8
375 mm Steel
screw
Socket cap
B
2. Attach the horizontal tube to the connector and
750 mm Steel
then rotate it by 90 degrees by hand.
A
screw
MR
the right side of frame B with a flat screw.
Causion:
R connector x8
pat the panel corner in one by one.
Rubber
* R connector for right side
M4 Hex screwdriver X1
sides of the horizontal tube are facing up.
R connector x4
M connector x8
375 mm Horizontal tube x8
Assembly Instructions
750 mm Horizontal tube x4
Flat head screw X8
Flat
head
screw
Causion:
* Fix the connectors to the frame C in the same order as
* Fix the R connector to the inside of frame D with a screw.
Model No.: SF-1315
Modello n.: SF-1315
Istruzioni per il montaggio
Telaio verticale x4 Connettore L x4 Connettore M x8
Connettore R x8 Connettore R x4 Cacciavite esagonale M4 x1 Tappo in gomma x8
Pannello d‘acciaio
da 750 mm x3
Pannello d‘acciaio
da 375 mm x10 Vite a testa piatta x8 Vite a esagono incassato x8 Tubo orizzontale da 375 mm x8 Tubo orizzontale da 750 mm x4
Vite a
esagono
incassato
Vite a
esagono
incassato
Vite a
testa
piatta
Vite a
testa
piatta
1. * Fissare il connettore L all‘interno del telaio A con una vite.
* Fissare il connettore R sul lato sinistro e il connettore M sul lato destro
del telaio B con una vite a testa piatta.
* Fissare i connettori al telaio C nello stesso ordine del telaio B.
* Fissare il connettore R all‘interno del telaio D con una vite.
Attention: * Il connettore L è per il lato sinistro
* Il connettore R è per il lato destro
* I connettori M sono da usare solo per la parte centrale
2. Attaccare il tubo orizzontale al connettore, quindi ruotarlo a mano
di 90 gradi.
Attention: * Assicurarsi che i fori concavi su entrambi i lati del tubo orizzontale
siano rivolti verso l‘alto.
* Assicurarsi che i fori per le viti del tubo orizzontale da 750 mm siano
rivolti verso l‘interno.
3. Inserire i pannelli un angolo alla volta, dare dei colpetti su ogni angolo
 noalloroinserimentoneltelaio.
4. Inserire a mano i tappi di gomma per i pannelli da 750 mm della base,
nei tubi orizzontali.

Flat
* M connectors for extention only
4. Insert rubber stoppers for 750 mm floor
Socket cap
panel x3
panels by hand into horizontal tubes.
panel x10
DC
tube 750 mm are facing inward.
R
head
M
L connector x4
*Make sure that screw holes of horizontal
*Make sure that the concave holes on both
screw
Socket cap screw X8
* Fix the R connector to the left side and M connector to
* L connector for left side
R
the frame B.
3. Press one side corner into the frame and then others,
Vertical frame x4
1. * Fix the L connector to the inside of frame A with a screw.
L
stopper x8
375 mm Steel
screw
Socket cap
B
2. Attach the horizontal tube to the connector and
750 mm Steel
then rotate it by 90 degrees by hand.
A
screw
MR
the right side of frame B with a flat screw.
Causion:
R connector x8
pat the panel corner in one by one.
Rubber
* R connector for right side
M4 Hex screwdriver X1
sides of the horizontal tube are facing up.
R connector x4
M connector x8
375 mm Horizontal tube x8
Assembly Instructions
750 mm Horizontal tube x4
Flat head screw X8
Flat
head
screw
Causion:
* Fix the connectors to the frame C in the same order as
* Fix the R connector to the inside of frame D with a screw.
Model No.: SF-1315