Jumbuck HS-16JCG601-B User manual

NATURAL GAS CONVERSION INSTRUCTIONS
This kit is only compatible with BBQ models listed on the table within
this instruction manual. Check your BBQ model is listed BEFORE
undertaking gas conversion using this kit.
Contents of this conversion kit
6 x 1.62mm Short injectors
6 x 1.65mm Short injectors
1 x 1.50mm Long injector
1 x 1.50mm Short injector
1 x 30cm Natural Gas hose
1 x brass fitting (Hose to Natural Gas regulator)
1 x Natural Gas regulator
1 x Ground fixing bracket and fasteners
1 x Natural Gas sticker
This kit does NOT include the gas line from supply point to the regulator inlet as each installation will
require a different length, connection type and diameter to meet gas flow requirements.
Introductory Statement
Your BBQ has been configured for use with LPG from a gas cylinder. If you want to connect
your BBQ to a permanent Natural Gas supply, the following steps must be undertaken.
1. Contact a licensed plumber or gas fitter and arrange a quote to convert your BBQ to
Natural Gas and supply any pipework necessary to bring a natural gas supply line to the BBQ
installation area. All works must be made in accordance with AS5601.1.
2. Undertake conversion to Natural Gas using these instructions and the parts contained in
this kit.
3. Obtain a certificate of compliance from your licensed gas fitter.
IMPORTANT: Refer to the instruction manual provided with your BBQ for installation
clearances.
Version 7
Release 9/11/2021 Page 1
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only

The injector is a precise gas metering restrictor, it is small and made of brass so
take care when removing and installing injectors.
The following steps must be followed to prevent damage to the injectors.
1. Use the correct size socket to remove the injectors. Do not use pliers,
vice grips, multi grips, or shifters.
2. Turn the socket anti clockwise to remove the injector.
3. After the first anti clockwise rotation, if you feel excess resistance, don’t force
the socket to turn anticlockwise, instead, turn the socket clockwise half a turn,
then continue to unscrew the injector anticlockwise, repeat if necessary. This
can help to loosen the sealant which is sometimes used during injector
installation.
4. After removal, blow air to clear the valve thread of any debris, check the valve
thread is clear, then install the replacement injectors with a socket and don’t
over tighten.
5. We recommend using a suitable gas connection thread sealant on the
replacement injector thread to prevent rework in case you encounter an
injector sealing face which does not seal on the valve seat. DO NOT use a
permanent thread locker.
6. When installing the replacement injectors, do not over torque the injectors.
INJECTOR/JET REMOVAL AND
INSTALLATION WARNING
Page 2
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021

Natural Gas Configuration for Jumbuck Stardom, Comet & Comet Plus
Natural Gas Configuration for Jumbuck Stardom II & Astro
This kit suits the models shown in the tables below. Ensure to set the aeration correctly and ensure to
install the correct injectors.
Note: If the LPG injector is a long type, you must replace it with a natural gas injector of the same length.
Page 3
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
MODELS
DESCRIPTION
HS-20201
Stardom II 2 Burner BBQ
HS-20401
Stardom II 4 Burner BBQ
HS-20601
Stardom II 6 Burner BBQ
HS-20JOK401
Stardom II Outdoor Kitchen BBQ
SYGP 4B
Astro 4 Burner SS BBQ
SYGP 6B
Astro 6 Burner SS BBQ
SYGP 4BB
Astro 4 Burner SS built in BBQ
BURNER
INJ.
JET
AERATION
SETTING
CONSUMPTION
(per burner)
BBQ
1.65
2mm Open
13 MJ/h
SIDE
1.5
Full Open
11.5 MJ/h
MODELS
DESCRIPTION
HS-884302
Stardom 2 Burner BBQ
HS-884502
Stardom 4 Burner BBQ
HS-885602
Stardom 6 Burner BBQ
HS-JOK403
Stardom Outdoor Kitchen BBQ
HS-18JOK403-2
Stardom Outdoor Kitchen BBQ
HS-16JCG401-S
Comet 4 Burner SS BBQ
HS-16JCG601-S
Comet 6 Burner SS BBQ
HS-16JCG401-B
Comet 4 Burner built in BBQ
HS-16JCG601-B
Comet 6 Burner built in BBQ
HS-18JCG401-GS
Comet Plus 4 Burner SS BBQ
HS-18JCG601-GS
Comet Plus 6 Burner SS BBQ
HS-18JCG401-GB
Comet Plus 4 Burner built in BBQ
HS-18JCG601-GB
Comet Plus 6 Burner built in BBQ
BURNER
INJ.
JET
AERATION
SETTING
CONSUMPTION
(per burner)
BBQ
1.62
2mm Open
13 MJ/h
SIDE
1.5
Full
Open
11.5 MJ/h
Version 7
Release 9/11/2021

Natural Gas Conversion Procedure
Gas conversion must be conducted by a licensed plumber or gas fitter only.
ŸInstall a gas isolation valve
at the gas supply point in an
easily accessible area.
ŸEnsure the pipework to the Natural Gas regulator is of sufficient diameter to meet the
demand of the BBQ.
ŸRemove BBQ burners and set aeration shutters to 2mm open.
ŸRemove side burner and set aeration shutter to full open.
ŸRemove LPG injectors and replace with Natural Gas injector sizes as stated on the
data label. The Natural gas configuration is also stated in the tables within this
instruction sheet.
ŸInstall burners.
ŸRemove 2.75kPa LPG hose and regulator assembly and replace with 10mm ID
Natural gas hose, brass adaptor and ½”BSP, 1.0kPa, Natural gas regulator.
ŸThread sealant or teflon tape must be used on all thread seal connections.
ŸLeak test all connections.
ŸSet the pressure to 1.0kPa with all burners on high.
ŸTest the operation of all burners on high and low to complete the commissioning
process.
Page 4
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021

Natural Gas Conversion Procedure - Continued
ŸFix the BBQ to the floor with the ground fixing bracket to prevent strain on the hose
and gas connections. This bracket fits in the LPG cylinder hole.
ŸInstruct the consumer on correct use of the BBQ and the location of the supply
isolation valve which must be closed after each use.
Page 5
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021

Page 6
Notes
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021

Page 7
This warranty in Australia is given by Pacific
Gas & Heating Pty Ltd, Tel: [phone].
Email: service@pacifictrends.com.au
The warranty in New Zealand is given by
Bunnings NZ Ltd, PO BOX 14436, Panmure,
Auckland, 1741.
Tel: [phone] Fax: [phone]
Email: [email protected]
Any claim under this warranty must be made
within 12 months of the date of purchase of
the product. Proof of purchase must be
presented.
Goods presented for repair may be replaced
by refurbished goods of the same type rather
than being repaired. Refurbished parts may
be used to repair the goods.
FOR AUSTRALIAN CUSTOMERS
To make a claim under the warranty please
contact the store where the product was
purchased or contact Pacific Gas & Heating
Pty Ltd directly.
CONDITIONS OF THE WARRANTY
The warranty covers domestic use only and
does not apply to commercial applications.
You may submit details and proof to our store
for consideration. The warranty covers
manufacture defects in materials,
workmanship and finish under normal use.
This warranty is provided in addition to other
rights and remedies you may have under law:
our goods come with guarantees which
cannot be excluded under the Australian
Consumer Law.
You are entitled to replacement or refund for a
major failure and to compensation for other
reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or
replaced if the goods fail to be acceptable
quality and the failure does not amount to a
major failure.
FOR NEW ZEALAND CUSTOMERS
To make a claim under the warranty, take the
product (with proof of purchase) to any
Bunnings store (See for www.bunnings.co.nz
store locations). This warranty is provided in
addition to other rights and remedies you may
have under law: our goods come with
guarantees which cannot be excluded under
the Consumer Guarantees Act 1993(NZ). You
are entitled to replacement or refund for a major
failure and to compensation for other
reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
Goods presented for repair may be replaced by
refurbished goods of the same type rather than
being repaired. Refurbished parts may be used
to repair the goods.
The warranty excludes damage resulting from
product misuse or product neglect.
The warranty covers domestic use only and
does not apply to commercial applications.
Thank you for purchasing one of our quality Jumbuck products. Your Jumbuck product is
covered against defects for a period of 12 months for parts and labour, repair or replacement.
This warranty excludes surface rust and damage caused by abuse or neglect.
PRODUCT WARRANTY
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021

Page 8
Please thoroughly read conditions of
warranty.
ŸThe appliance must be operated and
maintained in accordance with the
instructions supplied in the operating
manual.
ŸAny repair does not extend the
warranty period.
ŸAny parts other than original Jumbuck
parts will void this warranty.
INSTALLATION CONDITIONS
ŸAll installations must conform to the
applicable Electrical and Building
standards as laid down by the local
codes or state or region.
WHAT IS NOT COVERED IN THE
WARRANTY
ŸRemoval or re-installation costs. This
warranty does not cover costs for
transit nor in home service.
ŸLack of maintenance, abuse, neglect,
misuse, accidental or improper
installation of this appliance.
ŸScratches, dents, corrosion or
discolouration caused by heat,
abrasive chemical cleaners or
chipping.
ŸCorrosion or damage caused by
exposure to the elements such as
insects, weather or hail.
ŸCleaning and wear and tear; service
calls of this nature are chargeable.
ŸCommercial use of the product.
ŸUnauthorised repairs or modifications
during the warranty period.
ŸConsumable items, example –
heating elements.
RECORD THE FOLLOWING INFORMATION
Attach a copy of the purchase receipt here:
Date of purchase………………………………..
Purchased from………………………………...
Location………………………………………..
Model name and number……………………..
Date of manufacture……………………………
Receipt number………………………………...
FOR TECHNICAL ASSISTANCE
For Australian customers
If you experience any technical issues with your
Jumbuck product, in the first instance review the
instruction manual or call the warranty service
agent below.
For New Zealand Customers
If you experience any technical issues with your
Jumbuck product, in the first instance review the
instruction manual or call your local Bunnings
store.
WARRANTY CLAIMS
For Australian customers
Please contact Pacific Gas & Heating Pty Ltd,
Tel: [phone].
Email: service@pacifictrends.com.au
For New Zealand Customers
Please contact the store where the product was
purchased.
NG Conversion Instructions
Suits Jumbuck models Stardom, Stardom II, Comet, Comet Plus & Astro only
Version 7
Release 9/11/2021