Jumbuck HS-FP002 User manual

IMPORTANT! PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE!
IMPORTANT: READ THE ASSEMBLY INSTRUCTIONS IN THIS BOOKLET
BEFORE REMOVING THE CONTENTS OF THIS CARTON
IMPORTANT SAFETY INSTRUCTIONS
JUMBUCK RONDO MEDIUM 3180887
CHARCOAL SPIT ROASTER (HS-FP002)
SAFETY INSTRUCTIONS
FOR
OUTDOOR
USE ONLY
For outdoor use only.
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death.
Read the installation instructions thoroughly before installing this equipment.
Warning: accessible parts may be very hot. Keep young children away.
Do not move the appliance during use.
Any modification of the appliance may be dangerous and will void the
warranty.
Installer to leave instructions with the consumer and consumer to retain them
for future reference.
Please ensure all packaging and transit protection materials are removed prior
to using the spit roaster.
This appliance must only be used in an above
ground open-air situation with natural ventilation,
without stagnant areas, where products of
combustion are rapidly dispersed by
wind and natural convection
This SPIT ROASTER is an outdoor appliance only.
Under no circumstances should it be use indoors.
Do not store chemicals or flammable materials
near this appliance.
Unsupervised children should not be near the
SPIT ROASTER while cooking or during warm up
or cool down.
People with flammable clothing such as nylon
etc. should keep well away from the SPIT
ROASTER when it is operating.
Do not leave food unattended on the SPIT
ROASTER.
Particular care must be taken when removing the
ash OR used fuel. Hot ash can cause serious injury.
DO NOT OPERATE THIS APPLIANCE
BEFORE READING THE
INSTRUCTION BOOKLET
DO NOT PLACE ARTICLES ON OR
AGAINST THIS APPLIANCE
DO NOT STORE CHEMICALS OR
FLAMMABLE MATERIALS OR
SPRAY AEROSOLS NEAR THIS
APPLIANCE
DO NOT OPERATE THIS APPLIANCE
INDOORS
DO NOT ENCLOSE THIS APPLIANCE
DO NOT LIGHT OR OPERATE WITH THE
COVER ON(COVER NOT INCLUDED)

SPIT ROASTER OPERATING GUIDELINES
Lighting the spit roaster
solid fuel is to be used for this product (fire
wood, charcoal etc.)
place solid fuel into the spit roaster and light
using fire starters
let the solid fuel light (check occasional to
ensure fire is lit)
Cooking
ensure solid fuel is lit and that there is
sufficient heat for cooking
secure the food on the skewer, position skewer
at desired height and switch on the motor
the cooking grid can also be used to cook
regularly monitor temperature to ensure food
in not under or over cooked
Cleaning
once finish cooking, remove left over solid fuel
from the spit roaster
always ensure spit roaster is clean and free
from oil or grease (internally and externally) to
ensure longevity of the spit roaster
always keep spit roaster dry and under cover to
protect from weather and moisture
Pre-caution
always ensure hands are protected when
putting or removing food from the spit roaster
always ensure spit roaster is cool before
touching or cleaning the internal areas
always ensure hands are protected when
making adjustments to the air vent
do not use flammable liquids for igniting and
re-igniting
open flames and burning embers must never
be left unattended
after use, make sure the unit is allowed to cool
before moving

EXPLODED VIEW AND PARTS CODE
Part Number
Parts Description
Parts Code
1
Leg Back Asm
FP00201
2
Front Leg
FP00202
3
Wheel
FP00203
4
Body Asm
FP00204
5
Carbon Box
FP00205
6
Cooking Grid
FP00206
7
Right Motor Support
FP00207
8
Left Motor Support
FP00208
9
Motor
FP00209
10
Rotisserie Rod
FP00210
11
Rotisserie Brace
FP00211
12
Large Rotisserie Prong
FP00212
13
Rotisserie Support
FP00213
14
Rotisserie Handle
FP00214
15
Small Rotisserie Prong
FP00215

CARTON CONTENTS
1. Leg Back Asm ........ 2pcs
2.Front Leg.....….......... 2pcs
3. Wheel...…..…. 4pcs
4. Body Asm..………1pc
5. Carbon Box…….....1pc
6. Cooking Grid ..….…...2pcs
7.Right Motor Support…1pc
8.Left Motor Support…….1pc
9．Motor ……….1pc
10. Rotisserie Rod……….1pc
11. Rotisserie Brace…….1pc
12. Large Rotisserie Prong…….1pc
13.Rotisserie Support….1pc
14.Rotisserie Handle….2pcs
15. Small Rotisserie Prong….2pcs

HARDWARE PACK CONTENTS
A
Bolt M6x40mm
10pcs
B
Shrapnel ￠6
10pcs
C
Washer ￠6
10pcs
D
Nut M6
10pcs
E
Bolt M8X50
4pcs
F
Nut M8
4pcs
G
Bolt M6X10
1pc
H
Spanner
1PC

ASSEMBLY INSTRUCTIONS
Remove all contents from packaging, and make sure all the parts are present before attempting to
assemble! Tighten all bolt connections by hand first. When the spit roaster is fully assembled, retighten the
screws, nuts and bolts by using a wrench and screwdriver.
Step1: Assemble Front Leg (Part 2) to the Back Leg (Part 1), Use Bolt A, Shrapnel B Washer C Nut D to tighten
as shown.
Step 2: Assemble universal wheels to the legs.

Step 3: Assemble the two Leg Asm to the Body (Part 4), Use Bolt A, Shrapnel B Washer C Nut D to tighten as
shown.
Step 4: Put the Carbon Box (part 5) into the Body as shown.

Step 5: Insert the Cooking Grid (part 6) into the Body as shown.
Step 6: Assemble Right Motor Support (part 7) and Left Motor Support (Part 8) to the Leg, Use Bolt E Nut F to
tighten as shown.

Step 7: Insert Motor (Part 9) in the Right Motor Support (Part 7), as shown
Step 8: Insert Rotisserie Support (Part 13), Large Rotisserie Prong (Part 12), Rotisserie Brace (Part 11) , Small
Rotisserie Prong (Part 15) onto Rotisserie Rod (Part 10) as shown. Then assemble Rotisserie Handle (Part 14)
onto Rotisserie Support (Part 13) and Large Rotisserie Prong (Part 12), as shown.