JUMO mTRON T 570 User manual

JUMO mTRON T
Measuring, Control, and Automation System
Operating panels
Operating Manual
70506500T90Z001K000
V2.00/EN/00672050

3
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.1 Available technical documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.2 Base units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1.3 Input/output modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.4 Special modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.5 Operating, visualization, recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1.6 Power supply units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.1 Warning symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.2 Note signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2.3 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2.4 Qualification of personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3 Acceptance of goods, storage, and transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.1 Checking the delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.2 Notes on storage and transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.3 Returning goods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.4 Device version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.4.1 Order details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.4.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.4.3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5 Brief description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.6 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.7 Content of this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.1 Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 LAN connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.1 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Creating a PLC application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.1 Starting CODESYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.2 Mapping a variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.3 Select CODESYS feature set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.4 Install the repository package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.5 Insert the operating panel into the device tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.6 Transfer current firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.7 Add data server and data source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.8 Configure visualization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2.9 Close CODESYS project and save configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.2.10 Start CODESYS for debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Contents
4
3.2.11 Load configuration in operating panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.12 Create a boot application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.2.13 Close CODESYS project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.1 Operating panel 350 (type 705065/0x-1...) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2 Operating panel 570 (type 705065/0x-2...) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.3 Operating panel 1040 (type 705065/0x-5...) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5
1 Introduction
1.1 Available technical documentation
The documents specified below are available for the measuring, control, and automation sys-
tem (previous document number in parentheses).
1.1.1 General information
1.1.2 Base units
Product Type of documentation No. Printed PDF file
Measuring,
control, and
automation system
Data sheet 70500000T10... - X
System manual1
1Accessory subject to charge
70500000T90...
(B 705000.0) X-
Setup program manual 70500000T96...
(B 705000.6) -X
System description2
2Includes an overview of the purpose and content of all documents
70500000T98...
(B 705000.8) -X
Product Type of documentation No. Printed PDF file
Central
processing unit Data sheet 70500100T10... - X
Operating manual 70500100T90...
(B 705001.0) -X
Modbus interface description 70500100T92...
(B 705001.2.0) -X
PROFIBUS-DP interface description 70500103T92...
(B 705001.2.3) -X
digiLine interface description 70500106T92... - X
Installation instructions 70500100T94...
(B 705001.4) XX
CODESYS OPC server
operating manual 70500151T90... (B 705001.5.1) -X
Process engineering application
operating manual 70500152T90... - X
Operating manual
Thyristor power controller (type
70906x; integrationin the measuring,
control, and automation system)
70500153T90... - X

1 Introduction
6
1.1.3 Input/output modules
1.1.4 Special modules
Product Type of documentation No. Printed PDF file
Multichannel
controller module Data sheet 70501000T10... - X
Operating manual 70501000T90...
(B 705010.0) -X
Installation instructions 70501000T94...
(B 705010.4) XX
Relay module
4-channel Data sheet 70501500T10... - X
Operating manual 70501500T90...
(B 705015.0) -X
Installation instructions 70501500T94...
(B 705015.4) XX
Analog
input module
4-channel
Data sheet 70502000T10... - X
Operating manual 70502000T90...
(B 705020.0) -X
Installation instructions 70502000T94...
(B 705020.4) XX
Analog
input module
8-channel
Data sheet 70502100T10... - X
Operating manual 70502100T90...
(B 705021.0) -X
Installation instructions 70502100T94...
(B 705021.4) XX
Analog
output module
4-channel
Data sheet 70502500T10... - X
Operating manual 70502500T90... - X
Installation instructions 70502500T94... X X
Digital input/
output module
12-channel
Data sheet 70503000T10... - X
Operating manual 70503000T90...
(B 705030.0) -X
Installation instructions 70503000T94...
(B 705030.4) XX
Product Type of documentation No. Printed PDF file
Router module Data sheet 70504000T10... - X
Installation instructions 70504000T94...
(B 705040.4) XX

7
1 Introduction
1.1.5 Operating, visualization, recording
1.1.6 Power supply units
Product Type of documentation No. Printed PDF file
Multifunction
panel 840 Data sheet 70506000T10... - X
Operating manual 70506000T90...
(B 705060.0) -X
Modbus interface description 70506000T92...
(B 705060.2.0) -X
Installation instructions 70506000T94...
(B 705060.4) XX
Operating panels Data sheet 70506500T10... - X
Operating manual 70506500T90... - X
Product Type of documentation No. Printed PDF file
24 V power supply
units Data sheet 70509000T10... - X
Operating instructions QS5.241 X -
Operating instructions QS10.241 X -

1 Introduction
8
1.2 Safety information
1.2.1 Warning symbols
1.2.2 Note signs
DANGER!
This symbol indicates that personal injury caused by electrical shock may occur if the re-
spective precautionary measures are not carried out.
WARNING!
This symbol in connection with the signal word indicates that personal injury may occur if the
respective precautionary measures are not carried out.
CAUTION!
This symbol in connection with the signal word indicates that damage to assets or dataloss
will occur if the respective precautionary measures are not taken.
CAUTION!
This symbol indicates that components could be destroyed by electrostatic discharge
(ESD = Electro Static Discharge) if the respective cautionary measures are not taken.
Only use the ESD packages intended for this purpose to return device inserts, assembly
groups, or assembly components.
READ DOCUMENTATION!
This symbol – placed on the device – indicates that the associated device documentation
has to be observed. This is necessary to recognize the kind of the potential hazards as
well as the measures to avoid them.
TIP!
This symbol refers to important information about the product, its handling, or additional
use.
REFERENCE!
This symbol refers to further information in other sections, chapters, or manuals.
FURTHER INFORMATION!
This symbol is used in the tables and refers to further information in connection with the
table.
&
DISPOSAL!
This device and the batteries (if installed) must not be disposed in the garbage can after
use! Please ensure that they are disposed properly and in an environmentally friendly
manner.

9
1 Introduction
1.2.3 Intended use
The measuring, control, and automation system is intended for use in an industrial environ-
ment, as specified in the technical data of the individual system modules. Other uses beyond
those defined are not viewed as intended uses.
The modules are manufactured in compliance with the relevant standards and directives as
well as the applicable safety regulations. Nevertheless, improper use may lead to personal in-
jury or material damage.
To avoid dangers, the modules may only be used:
• For the intended use
• When in good order and condition
• When taking the technical documentation provided into account
Even if a module is used correctly and according to the intended use, it may still pose applica-
tion-related dangers, for example as the result of missing safety devices or incorrect settings.
To avoid incorrect settings, this manual contains relevant safety information and warnings.
These must be complied with.
1.2.4 Qualification of personnel
This document contains the information required to ensure that the measuring, control, and au-
tomation system described is used as intended.
It is intended for technically qualified personnel who have received special training and have
the appropriate knowledge in the field of automation technology (measuring and control tech-
nology).
Understanding and technically correct observance of the safety information and warnings in the
technical documentation supplied are prerequisites for safe startup as well as safety during op-
eration. Only qualified personnel have the required specialist knowledge to correctly interpret
and implement the safety information and warnings contained in this document in specific sit-
uations.
1.3 Acceptance of goods, storage, and transport
1.3.1 Checking the delivery
• Ensure that the packaging and contents are not damaged
• Check that the delivery is complete using the delivery papers and the order details
• Inform the supplier immediately if there is any damage
• Store damaged parts until clarification is received from the supplier
1.3.2 Notes on storage and transport
• Store the module in a dry and clean environment. Observe the admissible ambient condi-
tions (see "Technical data")
• The transport of the module is to be shockproof
• The original packaging provides optimum protection for storage and transport

1 Introduction
10
1.3.3 Returning goods
In the event of repair, please return the module in a clean and complete state.
Use the original packaging to return goods.
Accompanying letter for repair
Please include the completed accompanying letter for repair when returning goods.
Do not forget to state the following:
• Description of the application and
• Description of the error that has occurred
The accompanying letter for repair can be downloaded online from the manufacturer's website
(use the search function if necessary).
Protection against electrostatic discharge (ESD)
(ESD = electrostatic discharge)
To prevent damage from ESD, electronic modules or components must be handled, packaged,
and stored in an ESD-protected environment. Measures against electrostatic discharge and
electrical fields are described in DIN EN 61340-5-1 and DIN EN 61340-5-2 "Protection of elec-
tronic devices from electrostatic phenomena".
When returning electronic modules or components, please note the following:
• Sensitive components must only be packaged in an ESD-protected environment. Work-
spaces such as this divert electrostatic charges to ground in a controlled manner and pre-
vent static charges due to friction capacities.
• Only use packaging for ESD-sensitive modules/components. These must consist of con-
ductive plastics.
No liability can be assumed for damage caused by ESD.
1.3.4 Disposal
Disposing of the device
Disposing of the packaging material
The entire packaging material (cardboard packaging, inserts, plastic film, and plastic bags) is
fully recyclable.
CAUTION!
Electrostatic charges occur in non-ESD protected environments.
Electrostatic discharges can damage modules or components.
For transport purposes, use only the ESD packaging provided.
DISPOSAL!
Devices and/or replaced parts should not be placed in the refuse bin at the end of their ser-
vice life as they consist of materials that can be recycled by specialist recycling plants.
Dispose of the device and the packaging material in a proper and environmentally friendly
manner.
For this purpose, observe the country-specific laws and regulations for waste treatment and
disposal.