Juniper Srx1500 Setup guide

The SRX1500 Services Gateway is a next generation secure connectivity services

gateway for the cloud-enabled distributed enterprise edge and small to medium

data centers. Its advanced security and threat mitigation capabilities makes the

SRX1500 Services Gateway ideal for small to medium enterprises.

The SRX1500 Services Gateway has a modular 1-U chassis with twelve 1-Gigabit

Ethernet ports, four 1-Gigabit Ethernet SFP ports, four 10-Gigabit Ethernet SFP +

ports, and a 120 GB SSD (with 100 GB usable space). The SRX1500 Services

Gateway is available in both AC and DC models.

How to Set Up Your SRX1500 Services Gateway

Package Contents

Back Panel

Front Panel

g000879

Ethernet

ports

10G

SFP+

ports

Serial

Console

port

Reset

Conﬁg

button

Power

button

Control

port

ESD

point

LEDs

Mini-USB

Console

port

MGMT

port

USB

port

SFP

ports

Air inlet

WAN

PIM

slots

g000880

Grounding point

Fans Power supply slots

Speciﬁcation Value

Dimensions (H x W x D) 1.75 in. x 17.5 in. x 18.2 in.

(4.45 cm x 44.45 cm x 46.23 cm)

Chassis weight 15 lb. (6.8 kg)

Average power consumption 150 W

Maximum thermal output 300 BTU/hour

Relative humidity 5% to 90%, noncondensing

Noise level 66.5 dBA

g000878

SRX1500

USB cable

AC or DC power supply

Warranty and Registration

Information

DB-9 adapter

Screws

• End User License Agreement

• Safety Guide

• Quick Start Guide

Mounting brackets

AC power cable

RJ-45 cable

NOTE: The SRX1500 Services Gateway shipment package contains a

packing list. Check the parts in the shipment against the items on the

packing list. If anything is missing or damaged, contact your Juniper

Networks customer service representative.

How to Set Up Your SRX1500 Services Gateway 2

Factory-Default Settings

Interfaces

Interface Security Zone DHCP State IP Address

fxp0 192.168.1.1/24

ge-0/0/0 untrust Client Dynamically assigned

ge-0/0/1 trust Server 192.168.2.1/24

ge-0/0/2 trust 192.168.3.1/24

ge-0/0/3 trust 192.168.4.1/24

xe-0/0/16 trust 192.168.5.1/24

xe-0/0/17 trust 192.168.6.1/24

Security Policies

Source Zone Destination Zone Policy Action

trust trust permit

trust untrust permit

NAT Rules

Source Zone Destination Zone Policy Action

trust untrust Source NAT to untrust zone

interface

Services

SSH

HTTPS

NETCONF over SSH

Screens

Basic set of screens are enabled on the untrust zone

Initial Conﬁguration Process

g043458

Install Device

in a Rack

Connect

the Grounding

Cable

Conﬁgure Root

Authentication

Connect

to the

Console Port

Power On

the Device

Install the Device in a Rack

NOTE: Installing the device in a rack requires two people: one person lifts

the device while the other secures it to the rack.

1. Position a mounting bracket on each side of the chassis. Use a number-2

Phillips screwdriver to install the screws that secure the mounting brackets to

the chassis.

g000871

2. Have one person grasp the sides of the device, lift it, and position it in the rack.

Align the bottom hole in each mounting bracket with a hole in each rack rail,

making sure that the chassis is level.

3. Have a second person install a mounting screw into each of the two aligned

holes. Use a number-2 Phillips screwdriver to tighten the mounting screws.

How to Set Up Your SRX1500 Services Gateway 3

4. Install the second screw in each mounting bracket.

g000872

5. Verify that the mounting screws on one side of the rack are aligned with the

mounting screws on the opposite side and that the device is level.

Connect the Grounding Cable

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist,

and connect the strap to the ESD point on the chassis.

2. Connect the grounding cable to a proper earth ground.

3. Place the grounding cable lug over the grounding point on the upper rear of

the chassis.

CAUTION: The device should be permanently connected to ground

during normal operation. A licensed electrician must attach a cable lug

to the grounding cable. A cable with an incorrectly attached lug can

damage the device.

g000882

Grounding point

on the chassis

Grounding

lug

Grounding

screw

Locking

washer

4. Secure the grounding cable lug to the grounding point with the screw.

How to Set Up Your SRX1500 Services Gateway 4

Power On the Device

1. If you are using the AC model, perform the following steps:

a. Insert the appliance coupler end of the power cord into the appliance inlet

on the power supply and the power cord plug into an external AC power

source receptacle. Use a power cord retainer to hold the power cord in

place.

g000883

Power cord Power cord

retainer

b. Turn on the power to the AC power receptacle

2. If you are using the DC model, perform the following steps:

WARNING: Before performing the following procedure, ensure that

there is no power in the DC circuit. To ensure that all power is cut o,

locate the circuit breaker on the panel board that services the DC circuit,

switch the circuit breaker to the OFF (0) position, and tape the switch

handle of the circuit breaker in the OFF position.

a. Ensure that the voltage across the DC power source cable leads is 0 V

and that the cable leads do not become active while you are connecting

DC power.

b. Verify that the DC power cables are correctly labeled before making

connections to the power supply. In a typical power distribution scheme

where the return is connected to chassis ground at the battery plant, you

can use a multimeter to verify the resistance of the -48V and RTN DC

cables to chassis ground:

•The cable with very high resistance (indicating an open circuit) to chassis

ground will be connected to the V- (input) DC power input terminal.

•The cable with very low resistance (indicating a closed circuit) to chassis

ground will be connected to the V+ (return) DC power input terminal.

c. Remove the clear plastic cover from the terminal studs on the faceplate.

d. Remove the screws on the terminals by using a Phillips (+) screwdriver,

number 2.

e. Secure each positive (+) DC source power cable lug to a RTN (return)

terminal. Secure each negative (–) DC source power cable lug to a -48V

(input) terminal.

g0008

f. Replace the clear plastic cover over the terminal studs on the faceplate.

g. Remove the tape from the switch handle of the circuit breaker on the panel

board that services the DC circuit and switch the circuit breaker to the ON

(|) position.

How to Set Up Your SRX1500 Services Gateway 5

3. Note the following LED indications. Wait until the status LED (STAT) is solid

green before proceeding to the next step.

g000881

LED State

STAT •Solid green (operating normally)

ALARM •Solid amber (noncritical alarm)

•Solid red (critical alarm)

•O (no alarms)

SSD •Blinking green (the services gateway is transferring data

to or from the SSD storage device)

•O (SSD storage device not present)

PWR •Solid green (receiving power)

•Blinking green (receiving power—the services gateway is

in the bootup phase before OS initialization)

•Solid red (power supply unit failure)

HA •Solid green (all HA links are available)

•Solid amber (some HA links are unavailable)

•Solid red (device is inoperable because of a monitor

failure)

RPS •Solid green (redundant power supply is operating

normally)

•Solid red (the redundant power supply is not operating

normally)

•O (no redundant power supply)

Connect to the Console Port

1. Attach an ESD grounding strap to your bare wrist, and connect the strap to

the ESD point on the chassis.

2. Plug one end of the Ethernet cable into the Console port on your services

gateway.

g00088

Ethernet port

Console port

3. Connect the other end of the Ethernet cable to the RJ-45—to—DB-9 serial

port adapter supplied with your services gateway.

4. Connect the RJ-45—to—DB-9 serial port adapter into the serial port on the

management device. Use the following values to conﬁgure the serial port:

Baud rate—9600; Parity—N; Data bits—8; Stop bits—1; Flow control—None.

NOTE: Alternately, you can use the USB cable to connect to the mini-

USB console port on the services gateway. To use the mini-USB console

port, you must download a USB driver to the management device from

the Silicon Labs page.

How to Set Up Your SRX1500 Services Gateway 6

Conﬁgure Root Authentication

Before you can use J-Web to conﬁgure your device, you must access the CLI to

conﬁgure the root authentication and the management interface.

1. Log in to the device as root. When the device is powered on with the factory-

default conﬁguration, you do not need to enter a password.

2. At the (%) prompt, type cli to start the CLI and press Enter. The prompt

changes to an angle bracket (>) when you enter the CLI operational mode.

root%cli

root>

3. At the (>) prompt, type conﬁgure and press Enter. The prompt changes from

> to # when you enter the conﬁguration mode.

root> congure

Entering conguration mode

[edit]

root#

4. Set the root authentication password by entering a cleartext password, an

encrypted password, or an SSH public key string (DSA or RSA).

root# set system root-authentication plain-text-password

New password: password

Retype new password: password

5. Conﬁgure the route for the management interface (optional, required only if

you do not connect the MGMT port directly to the management device).

root# set routing-options static route <destination

prex> next-hop <gateway>

6. Commit the conﬁguration changes.

root# commit

7. Connect the MGMT port on the device to the Ethernet port on the

management device using an RJ-45 cable.

8. Conﬁgure an IP address on the 192.168.1.0/24 subnetwork for the

management device. By default, the management interface is conﬁgured with

the 192.168.1.1/24 IP address. If you need to change the IP address, perform

the following steps or else proceed to Step 9:

a. Delete the default management interface IP address:

root# delete interface fxp0 unit 0 family inet address

192.168.1.1/24

b. Conﬁgure a new IP address for the management interface:

root# set interfaces fxp0 unit 0 family inet address

ad dress/prex-length

c. Commit the conﬁguration changes.

root# commit

d. Conﬁgure an IP address for the management device. Ensure that the IP

address is on the same subnetwork as the management interface (fxp0).

9. Launch a Web browser from the management device and access the services

gateway using the URL https://192.168.1.1. If you changed the management

interface IP address in Step 8, then use the URL https://<management IP

address> to access the services gateway.

NOTE: As the system-generated certiﬁcate is not trusted by default, an

alert is displayed. You can ignore this alert and proceed to access the

services gateway.

The J-Web login page is displayed. This indicates that you have successfully

completed the initial conﬁguration and that your SRX1500 Services Gateway

is ready for use.

How to Set Up Your SRX1500 Services Gateway 7

10. Log in as root and proceed with conﬁguring the settings based on your

requirements.

Verify Device Operation

1. Connect port 0/0 to the ISP device to obtain a dynamic IP address.

2. Connect a laptop to the ge-0/0/1 port. In default conﬁguration mode,

the ge-0/0/1 port acts as a DHCP server and assigns an IP address and

conﬁguration settings such as nameserver and gateway IP address to the

client (laptop).

Once this process is complete, open a webpage to verify that you can access

the Internet. This ensures that you can pass trac through the services

gateway.

Power O the Device

To power o the device, press the Power button on the front of the device and

hold it for 10 seconds.

Reset the Conﬁguration

Pressing and holding the RESET CONFIG button for 5 seconds or more deletes

all conﬁgurations (backup conﬁgurations and rescue conﬁguration) on the

device, and loads and commits the factory conﬁguration.

Next Steps

For information on conﬁguring features on your services gateway, refer the

following:

•Junos OS Documentation/Feature Conﬁguration

http://www.juniper.net/techpubs/en_US/release-independent/junos/

information-products/pathway-pages/srx-series/product/index.html

•Getting Started Knowledge Base Article

https://kb.juniper.net/InfoCenter/index?page=content&id=KB15694

Reference

Technical Support

http://www.juniper.net/support/requesting-support.html

SRX1500 Services Gateway Hardware Guide

http://www.juniper.net/techpubs/en_US/release-independent/junos/

information-products/pathway-pages/hardware/srx1500/index.html

Supported Transceivers

https://pathﬁnder.juniper.net/hct/product/#prd=SRX1500

Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper

Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks

reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Part Number: 530-072461 Revision 01, October 2016.

Other manuals for SRX1500

Table of contents

Other Juniper Gateway manuals