Juniper SSR1500 Installation instructions

SSR1500 Appliance Hardware Guide
Published
2022-12-13

Juniper Networks, Inc.
1133 Innovaon Way
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc.
in the United States and other countries. All other trademarks, service marks, registered marks, or registered service
marks are the property of their respecve owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right
to change, modify, transfer, or otherwise revise this publicaon without noce.
SSR1500 Appliance Hardware Guide
Copyright © 2022 Juniper Networks, Inc. All rights reserved.
The informaon in this document is current as of the date on the tle page.
YEAR 2000 NOTICE
Juniper Networks hardware and soware products are Year 2000 compliant. Junos OS has no known me-related
limitaons through the year 2038. However, the NTP applicaon is known to have some diculty in the year 2036.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentaon consists of (or is intended for use
with) Juniper Networks soware. Use of such soware is subject to the terms and condions of the End User License
Agreement ("EULA") posted at hps://support.juniper.net/support/eula/. By downloading, installing or using such
soware, you agree to the terms and condions of that EULA.
ii

Table of Contents
About This Guide | vi
1
Overview
SSR1500 Appliance Overview | 2
Benets of SSR1500 | 2
Field-Replaceable Units in SSR1500 Appliances | 3
SSR1500 Chassis | 3
Front Panel of an SSR1500 | 4
Rear Panel of an SSR1500 | 5
Chassis Physical Specicaons for SSR1500 | 5
Chassis Status LEDs | 6
Network Port LEDs | 7
Cooling System | 8
Power System | 9
2
Site Planning, Preparaon, and Specicaons
Site Preparaon Checklist for SSR1500 | 14
SSR1500 Site Guidelines and Requirements | 15
General Site Installaon Guidelines | 16
Site Electrical Wiring Guidelines | 16
Environmental Requirements and Specicaons for SSR1500 | 18
Clearance Requirements for Hardware Maintenance of SSR1500 | 18
Rack Requirements for SSR1500 | 19
Cable Specicaons and Pinouts for SSR1500 | 22
Transceiver Support for SSR1500 | 22
3
Inial Installaon and Conguraon
iii

Unpack and Mount an SSR1500 | 25
Tools and Parts Required to Unpack the SSR1500 Appliance | 25
Unpack an SSR1500 | 25
Verify Parts Received with the SSR1500 | 26
Install the SSR1500 in a Rack | 27
Connect SSR1500 to Power | 31
Connect Earth Ground to SSR1500 | 31
Connect Power to SSR1500 | 33
Power O the SSR1500 | 35
Connect SSR1500 to External Devices | 36
Connect SSR1500 to a Management Console | 36
Onboarding SSR Conductor Managed SSR1500 onto Mist | 37
4
Maintaining Components
Maintaining the SSR1500 Hardware Components | 47
SSR1500 Fan Maintenance | 47
Remove a Fan from the SSR1500 | 48
Install a Fan in the SSR1500 | 48
SSR1500 Power Supply Maintenance | 49
Replacing an AC Power Supply on the SSR1500 | 49
Remove an AC Power Supply from an SSR1500 | 50
Install an AC Power Supply in an SSR1500 | 50
Unmount the SSR1500 Chassis | 51
Remove the SSR1500 from a Rack | 51
5
Contacng Customer Support and Returning the Chassis or Components
Contacng Customer Support and Returning the Chassis or Components | 54
How to Return a Hardware Component to Juniper Networks, Inc. | 54
Locate the Chassis Serial Number ID Label | 56
iv

Contact Customer Support to Obtain Return Material Authorizaon | 56
Guidelines for Packing and Shipping Hardware Components | 57
6
Safety and Compliance Informaon
Denions of Safety Warning Levels | 59
General Safety Guidelines and Warnings | 60
Restricted Access Warning | 62
Qualied Personnel Warning | 63
Prevenon of Electrostac Discharge Damage | 64
Fire Safety Requirements | 65
Laser and LED Safety Guidelines and Warnings | 67
Chassis and Component Liing Guidelines | 70
Radiaon from Open Port Apertures Warning | 70
Maintenance and Operaonal Safety Guidelines and Warnings | 71
Acon to Take Aer an Electrical Accident | 77
General Electrical Safety Guidelines and Warnings | 77
SSR1500 Agency Approvals | 79
FCC Declaraons | 81
Lithium Baery Declaraon | 81
v

About This Guide
Use this guide to install hardware and perform inial soware conguraon, roune maintenance, and
troubleshoong for the SSR1500 appliance. Aer compleng the installaon and basic conguraon
procedures covered in this guide, refer to the Session Smart Router soware documentaon for
informaon about further soware conguraon.
vi

1
CHAPTER
Overview
SSR1500 Appliance Overview | 2
SSR1500 Chassis | 3

SSR1500 Appliance Overview
IN THIS SECTION
Benets of SSR1500 | 2
Field-Replaceable Units in SSR1500 Appliances | 3
The Juniper Networks SSR1500 is a 1-U xed-conguraon appliance that is ideal for large data center
or campus deployments. Powered by the Juniper Session Smart Router (SSR) soware, the SSR1500
provides secure and resilient WAN connecvity.
The SSR1500 provides high port density with four Ethernet ports and twelve SFP28 ports. The SFP28
ports support port speeds of 1/10/25 Gbps. Dual hot-swappable AC power supplies provide 1+1
redundancy.
NOTE: To use the SSR1500, you must purchase the SSR soware subscripon license that is sold
separately. You can onboard and monitor the SSR1500 in a cloud network by using Juniper
Mist™.
Benets of SSR1500
•Zero Trust Security (ZTS)—The SSR1500 ensures ZTS by authencang all routes and encrypng all
session trac. Applicaons, devices, or users cannot iniate any session that does not comply with
the authencaon policies and access rules. The SSR1500 supports Layer 2 through Layer 5 stateful
rewall funcons, including DoS/DDoS protecon, NAT, encrypon, VPN, and trac ltering.
•Adapve encrypon—The SSR1500 automacally detects trac encrypted using HTTPS or IPsec
and does not re-encrypt such trac. This capability results in improved performance and reduced
overhead due to double encrypon.
•Simplied onboarding and monitoring with Juniper Mist WAN Assurance—You can quickly onboard
the SSR1500 to the Mist Cloud using the claim code (QR code). This helps in reducing the
operaonal complexity and simplifying the deployment and conguraon process.
2

NOTE: Starng from SSR Release 6.0, you can manage the SSR1500 using Juniper Mist WAN
Assurance.
Field-Replaceable Units in SSR1500 Appliances
Field-replaceable units (FRUs) are components that you can replace at your site. Following are the two
types of the SSR1500 FRUs:
• Hot-insertable and hot-removable—You can remove and replace these components without powering
o the appliance or disrupng the appliance funcon.
• Hot-pluggable—You can remove and replace these components without powering o the appliance,
but the appliance funcon is interrupted unl you replace the component.
The FRUs in SSR1500 appliances are:
• Fans (hot-insertable and hot-removable)
• Power supplies (hot-insertable and hot-removable)
• Transceivers (hot-pluggable)
SSR1500 Chassis
IN THIS SECTION
Front Panel of an SSR1500 | 4
Rear Panel of an SSR1500 | 5
Chassis Physical Specicaons for SSR1500 | 5
Chassis Status LEDs | 6
Network Port LEDs | 7
Cooling System | 8
Power System | 9
3

Front Panel of an SSR1500
Figure 1 on page 4 shows the front panel of an SSR1500. The SSR1500 comes with a claim code (QR
code) that you can use to onboard the SSR1500 to Juniper Mist.
Figure 1: Front Panel Components of SSR1500
1—Chassis LEDs 5—RJ-45 Console port
2—USB 3.0 ports
NOTE: Do not use SanDisk Ultra Fit
USB 3.1 SDCZ430 32GB/64GB/
128GB and SanDisk Ultra USB 3.0
SDCZ48 32 GB USBs.
6—1 GbE management port (for Mist operaons)
3—1/10/25 GbE SFP28 ports (2/0 through 4/3) 7—RESET buon
4—1 GbE Ethernet ports (1/0 through 1/3) 8—Claim code
4

Rear Panel of an SSR1500
Figure 2 on page 5 shows the rear panel of an SSR1500.
Figure 2: Rear Panel Components of SSR1500
1—AC power supply units 3—Fans
2—Power switch 4—Earth grounding
Chassis Physical Specicaons for SSR1500
Table 1 on page 5 summarizes the physical specicaons of SSR1500.
Table 1: Physical Specicaons of SSR1500
Model Height Width Depth Weight
SSR1500 44 mm 438 mm 610 mm 22 kg (48.51 lbs.)
5

Chassis Status LEDs
Figure 3 on page 6 shows the LEDs on the front panel, and Table 2 on page 6 describes the LEDs.
Figure 3: SSR1500 Chassis LEDs
Table 2: SSR1500 Front Panel LEDs
Callout LED Descripon
1 Power •Solid green—The device is
powered on.
•O—The device is powered o.
2 Status •Solid green—The device is
operang normally.
•Solid red—Indicates a major
alarm, such as a hardware
component failure.
•O—The device is not receiving
power.
3 SSD •Blinking amber—Indicates SSD
acvity.
•O—There is no SSD acvity.
6

Network Port LEDs
Each network port uses two LEDs to indicate the link acvity and speed. Figure 4 on page 7 shows
the locaon of the LEDs on the Ethernet and SFP28 ports.
Figure 4: LEDs on the Ethernet and 1/10/25G SFP28 Ports
Table 3 on page 7 describes the LEDs on the Ethernet ports.
Table 3: LEDs on the Ethernet Ports
Callout LED Descripon
1 Link Acvity (LED on the le) •Blinking amber—Link is
established and there is acvity
on the port.
•Solid amber—Link is established
but there is no acvity on the
port.
•O—There is no link
established.
2 Speed (LED on the right) •Solid amber—The link is
operang at 1 Gbps speed.
•Solid green—The link is
operang at 100 Mbps speed.
•O—The link is operang at 10
Mbps speed.
Table 4 on page 8 describes the LEDs on the SFP28 ports.
7

Table 4: LEDs on the 1/10/25G SFP28 Ports
Callout LED Descripon
1 Link Acvity (LED on the le) •Blinking green—Link is
established and there is acvity
on the port.
•Solid green—Link is established
but there is no acvity on the
port.
•O—There is no link
established.
2 Speed (LED on the right) •Solid green—The link is
operang at 1/10 Gbps speed.
•Solid amber—The link is
operang at 25 Gbps speed.
Cooling System
The cooling system of the SSR1500 consists of ve fans, which are hot-insertable and hot-removable
eld-replaceable units (FRUs). You can remove and replace them without powering o the appliance or
disrupng appliance funcons.
The SSR1500 appliances have front-to-back airow. The air is pulled in through the front of the chassis
toward the fan modules, from where it is exhausted out of the chassis.
8

Figure 5: Airow Through the SSR1500 Chassis
Power System
IN THIS SECTION
AC Power Cord Specicaons for SSR1500 | 10
The SSR1500 appliance ships with two AC power supply units (1+1 redundancy) preinstalled. Each
power supply unit is a hot-removable and hot-insertable eld-replaceable unit (FRU) when the second
power supply is installed and running. You can remove and replace either one of them without powering
o the appliance or disrupng the appliance funcons.
NOTE: If both power supply units are installed, and if only one power supply unit is connected to
the power source, the appliance raises an alarm.
Each power supply has its own fan and is cooled by its own internal cooling system.
Table 5 on page 10 lists the power specicaons for the SSR1500 appliance.
9

Table 5: Power Supply Specicaons for SSR1500
Model AC Input
Voltage
(Operang
Range)
AC Input Line
Frequency
AC Input
Current Rang
Maximum
Power
Consumpon
Power Supply
Type
SSR1500 100–240 VAC 50–60 Hz 3–5 A 550 W External, hot
swappable
AC Power Cord Specicaons for SSR1500
We ship detachable region-specic AC power cords with the chassis. The coupler is type C15 as
described by Internaonal Electrotechnical Commission (IEC) standard 60320. The plug end of the
power cord ts into the power source outlet that is standard for your geographical locaon.
Table 6 on page 10 lists the AC power cords specicaons provided for the power supplies for each
country or region.
Table 6: AC Power Cord Specicaons for SSR1500
Country/
Region
Electrical
Specicaons
Plug Standards Juniper Model
Number
Graphic
Argenna 250 VAC, 10 A,
50 Hz
IRAM 2073 Type
RA/3
CBL-EX-PWR-C13-
AR
No graphic available
Australia 250 VAC, 10 A,
50 Hz
AS/NZS 3112 Type
SAA/3
CBL-EX-PWR-C13-
AU
Brazil 250 VAC, 10 A,
50 Hz
NBR 14136 Type
BR/3
CBL-EX-PWR-C13-
BR
No graphic available
10

Table 6: AC Power Cord Specicaons for SSR1500 (Connued)
Country/
Region
Electrical
Specicaons
Plug Standards Juniper Model
Number
Graphic
China 250 VAC, 10 A,
50 Hz
GB 1002-1996
Type PRC/3
CBL-EX-PWR-C13-
CH
Europe
(except
Italy,
Switzerland
, and
United
Kingdom)
250 VAC, 10 A,
50 Hz
CEE (7) VII Type
VIIG
CBL-EX-PWR-C13-
EU
India 250 VAC, 10 A,
50 Hz
IS 1293 Type
IND/3
CBL-EX-PWR-C13-IN No graphic available
Israel 250 VAC, 10 A,
50 Hz
SI 32/1971 Type
IL/3G
CBL-EX-PWR-C13-IL
Italy 250 VAC, 10 A,
50 Hz
CEI 23-16 Type
I/3G
CBL-EX-PWR-C13-IT
Japan 125 VAC, 12 A,
50 Hz or 60 Hz
SS-00259 Type
VCTF
CBL-EX-PWR-C13-JP
11

Table 6: AC Power Cord Specicaons for SSR1500 (Connued)
Country/
Region
Electrical
Specicaons
Plug Standards Juniper Model
Number
Graphic
Korea 250 VAC, 10 A,
50 Hz or 60 Hz
CEE (7) VII Type
VIIGK
CBL-EX-PWR-C13-
KR
North
America
125 VAC, 13 A,
60 Hz
NEMA 5-15 Type
N5-15
CBL-EX-PWR-C13-
US
South
Africa
250 VAC, 10 A,
50 Hz
SABS 164/1:1992
Type ZA/3
CBL-EX-PWR-C13-
SA
Switzerland 250 VAC, 10 A,
50 Hz
SEV 6534-2 Type
12G
CBL-EX-PWR-C13-
SZ
No graphic available
United
Kingdom
250 VAC, 10 A,
50 Hz
BS 1363/A Type
BS89/13
CBL-EX-PWR-C13-
UK
12

2
CHAPTER
Site Planning, Preparaon, and
Specicaons
Site Preparaon Checklist for SSR1500 | 14
SSR1500 Site Guidelines and Requirements | 15
Cable Specicaons and Pinouts for SSR1500 | 22

Site Preparaon Checklist for SSR1500
The checklist in Table 7 on page 14 summarizes the tasks you need to perform when preparing a site
for SSR1500 installaon.
Table 7: Site Preparaon Checklist for SSR1500 Installaon
Item or Task Addional Informaon
Environment
Verify that environmental
factors such as temperature
and humidity do not exceed
device tolerances.
"Environmental Requirements and Specicaons for SSR1500" on page 18
Power
Measure the distance
between the external power
sources and the device
installaon site.
Locate sites for connecon of
system grounding.
Calculate the power
consumpon and
requirements.
Rack Requirements
Verify that your rack meets
the minimum requirements.
"Rack Requirements for SSR1500" on page 19
Rack Installaon
14