Jura Impressa F9 guide User manual

Sensor-Touch Display
Right
Control Buttons
Hot
Water Steam
Left Control Buttons
RINSE
2Cup
Ground
Coffee
ON/OFF
1Cup
PROGRAM
SELECT PRODUCT
ST@RT
Big Cup Coffee Espresso Mild Normal Strong
Impressa F9 Quick Reference Guide
This Guide does not replace the Operating Instructions.
For details and cautions you must read all instructions.
Traces of Coffee Grounds in New Machine?
This is normal! Grinder was tested during assembly with beans.
Despite cleaning, traces of ground coffee may be found.
GREEN TEXT represents information in the display.
A) First Time Ever Preparation
1. Fill water in tank and beans in bean container.
2. DO NOT install the Claris Filter Cartridge now!
3. Push ON/OFF button. When the display reads FILL
SYSTEM / WATER PORTION place a cup underneath
the frother and push the HOT WATER button. When the
F9 stops pumping: YOUR MACHINE IS HEATING.
4. Then PRESS MAINT.Place a cup under the coffee
spouts and press the RINSE button. Display reads SELECT
PRODUCT and the complete touch screen is illuminated.
5. Place a cup underneath the coffee spout, touch the
ESPRESSO symbol, then touch the 3-BEAN symbol,
ESPRESSO STRONG.Touch and hold the ST@RTsymbol
until machine starts grinding. Repeat once. Discard the
first two cups of coffee.
B) Daily Preparation
•Fill fresh water in tank and check bean container.
• Push ON/OFF button. HELLO YOUR MACHINE IS HEAT-
ING.PRESS MAINT. Place a cup under the coffee spout
and press the RINSE button. SELECT PRODUCT.

C) Factory Settings
.......................
D) Grinding and Brewing Coffee
Nine coffee options in the Sensor Touch Display: BIG CUP,
COFFEE, ESPRESSO each in MILD, NORMAL, STRONG.
• Select a coffee option and gently touch and hold
ST@RT for two seconds until grinding starts.
Two coffee options with the 1-Cup and 2-Cup buttons.
Push either button. Grinding and brewing starts immediately.
E) Changing the Grinder Fineness
Important:You can only adjust the fineness during the actual
grinding process.
•Open the bean container lid and turn the dial while grinding.
Thicker bars: coarser; thinner bars: finer.
•For darker, oily beans, grind somewhat coarser.
•For lighter beans, grind somewhat finer.
F) Using Hot Water
Place a cup underneath the steam nozzle. Push the HOT
WATER button. WATER PORTION.Push button again to stop.
G) Using Steam (Frothing and Steaming)
Important:Frother parts must be tightly connected and clean.
• Cappuccino: One shot espresso plus ~4 oz. of steamed
and frothed milk. Metal frother sleeve DOWN.
• Latte: One shot espresso plus 4 to 5 oz. of steamed milk.
Metal frother sleeve UP.
1. Push the STEAM button. The button’s red light starts
blinking. YOUR MACHINE IS HEATING.After 20 sec.:
SELECT PRODUCT.
2. Immerse the frother into a pitcher with milk and push the
STEAM button again. STEAM PORTION.Steam pushes
into the milk.
3. Push the STEAM button again to stop. SELECT PRODUCT.
To continue steaming push the STEAM button again.
4. After steaming you can immediately brew coffee.
Knocking Noise during Frothing:The F9 pumps water
droplets for steam. This is normal. Please note: Skim and
1% milk will produce more froth than 2% or regular milk.
Regulating Milk Temperature
To increase the milk temperature use the steaming position.
H) Cleaning the Frother
Should be done right after use, takes less than 15 sec. !
Place a cup underneath the frother. Push the HOT WATER
button. After 5 sec. push the button again to stop.
I) Programming
Filter .................... No
Hardness Level ... 2
Aroma................... Strong
Temperature ........ High
Time ..................... Not set
Unit (auto) On ..... Not set
Auto Off ............... 2 hours
BIG CUP ................ 240 ml (8 oz)
COFFEE.................. 150 ml (5 oz)
ESPRESSO............. 60 ml (2 oz)
1-CUP...................... 120 ml (4 oz)
2-CUP...................... 240 ml (8 oz)
WATER PORTION... 5 oz
LANGUAGE............ English

Push and hold the Pbutton until two Red Arrows show in
the display. First message: FILTER NO.Repeatedly pushing
the right arrow accesses different factory settings. Push the
Pbutton again to return to SELECT PRODUCT.
Here is how to change some of the settings (for all other set-
tings refer to the Operating Instructions).
a) Programming Cup Size for Sensor Touch Symbols
BIG CUP, COFFEE and ESPRESSO symbols can be pro-
grammed between 1 and 8 oz. each (30 to 240 ml).
1. Press and hold the Pbutton until FILTER NO.Press the
Right Arrow 4times: WATER QUANTITY
2. Touch ST@RT and touch the cup symbol for which you
want to change the cup size, e.g. COFFEE 5 OZ (120ml)
3. Press either arrow repeatedly to change the cup size.
Touch ST@RT to confirm. WATER QUANTITY.
4. You can touch another cup symbol and proceed as above.
5. Press Pbutton to return to SELECT PRODUCT.
b) Programming 1-CUP Button
The 1-CUP button can be programmed between 1 and 8 oz.
The 2-CUP button delivers always twice as much coffee.
1. Press and hold the Pbutton until FILTER NO.Press the
Right Arrow 5times: 1-CUP 4 OZ (120 ML)
2. Press either arrow repeatedly to change. Touch ST@RT to
confirm. 1-CUP STRONG.Touch one of the bean symbols
to select MILD, NORMAL or STRONG, e.g. 1-CUP NORMAL.
Touch ST@RT to confirm. 1-CUP NORMAL.
3. Press Pto return to SELECT PRODUCT.
c) Programming Hot Water Portion
Hot water portion can be programmed between 1 and 16 oz.
1. Press and hold the Pbutton until FILTER NO.Press the
Right Arrow 7times: WATER PORTION
2. Touch [e-mail] KEY.Place a cup under the frother
and press the HOT WATER button. Hot water will be
released. ENOUGH WATER? PRESS KEY.When the
desired amount of hot water is in your cup press the HOT
WATER button to stop. WATER PORTION.This amount
of hot water is now programmed.
3. Press Pto return to SELECT PRODUCT.
d) Setting Time and Programming Auto-On
1. Press and hold the Pbutton until FILTER NO.Press the
Right Arrow 8times: TIME --.--
2. Touch [e-mail] touch the arrows to set the
hours (military time!). Touch ST@RT to confirm.
3. Repeatedly touch the arrows to set the minutes. Touch
ST@RT to confirm.
4. Press the Right Arrow once UNIT ON --.--. Touch ST@RT.
5. Set the Auto-On time like the time (arrows for hours,
ST@RT to confirm, arrows for minutes, ST@RT to confirm.
6. Press Pto return to SELECT PRODUCT.
The F9 will turn on automatically at the preset time.

J)Installing the Claris Cartridge (F9 is on)
1. Rinse cartridge under running water and insert
into water tank reception. Close cartridge holder.
2. Fill tank with cold water. Push and hold the Pbutton:
FILTER NO.Touch [e-mail] starts blinking.
3. Touch red arrow once: FILTER YES.Touch ST@RT to
confirm.
4. INSERT FILTER / WATER PORTION.Place a large
container (30 oz.) under the frother and push the
HOT WATER button. FILTER RINSING.After ~90
sec.: YOUR MACHINE IS HEATING then SELECT
PRODUCT.
The F9 automatically reminds you when it’s time to
replace the cartridge. Please note: When the Claris
program is activated, the decalcifying monitor is
turned off .
K) Replacing the Cartridge
The display shows REPLACE FILTER / SELECT
PRODUCT
• Remove old filter, rinse new filter under running
water and insert (see above). Place a large container
(30 oz.) under the frother. Turn the machine off.
Now, push and hold the RINSE button.
•WATER PORTION / INSERT FILTER.Push the
HOT WATER button.
Important:If message REPLACE FILTER does not
appear after 6 weeks, you must still replace the filter.
L) Cleaning with Special Tablet
This cleaning cycle removes coffee oils inside the
machine. This message will appear after 200 cups of
coffee: CLEAN MACHINE / SELECT PRODUCT. Takes
less than 10 minutes!
Important:Only use special round cleaning tablets!
Important:Once started, do not interrupt the program!
1.Fill water tank. Push and hold the RINSE button.
EMPTY TRAY.Please note:You must remove the
tray for 20 seconds, even if it is empty. Replace tray.
2.PRESS MAINT.Push the RINSE button. MACHINE
CLEANING.After a moment the display shows
TABLET / PRESS MAINT.
3. Drop one white tablet into the "ground coffee funnel."
Push the RINSE button. MACHINE CLEANING.
After a few minutes: EMPTY TRAY.Carefully lift,
remove and empty tray and replace. The F9 returns
to its standard message SELECT PRODUCT and
resets itself.
M) Decalcifying
If a water hardness level is selected (see Operating
Instructions), the decalcifying monitor is active. The F9
needs to be de-calcified when the message MACHINE
SCALED SELECT PRODUCT appears.

Important:If you use the Claris filter and the above
message appears then the Claris activation was not
performed. Repeat all steps of Chapter J. This will turn
off the decalcifying monitor.
Important:Never interrupt the decalcifying program.
• Use only the special decalcifying tablets (not the
cleaning tablets!). For supplies see below.
1. Turn the F9 off and let cool down for one hour.
Push and hold the RINSE button until display shows
EMPTY TRAY.
2. Remove and empty tray. You must remove the tray
for 20 seconds even if it is empty. Replace tray.
Decalcifying Session:
3. AGENT IN TANK / PRESS MAINT.Dissolve three
large square tablets in 16 oz. of water and pour
mixture into water tank. Place a container (at least
16 oz.) under frother.
4. Push the RINSE button. MACHINE DESCALED.
After a few minutes: EMPTY TRAY.Carefully
remove cup and tray, empty and replace.
Cleaning Session:
5. FILL WATER.Rinse water tank and fill with cold
water (16 oz.) and replace. Place a container under
the frother.
6. PRESS MAINT.FILL WATER.Push the RINSE
button. MACHINE DESCALED.After a few minutes:
EMPTY TRAY.Carefully remove cup and tray, empty
and replace.
7. PRESS MAINT.Push the RINSE button. The F9
returns to SELECT PRODUCT and resets itself.
8. Clean the chrome front and grid with a moist, soft
cloth.
CAPRESSO CUSTOMER SERVICE
1-800-220-5701
M-F 9AM - 9PM; Sat. 9AM - 5PM EST
FAX: [phone]
[email protected]
N) Supplies
Order through Customer Service or Mail Order Form or
www.capresso.com:
•Claris Water Filter Cartridge: #7520
•Special Cleaning Tablets: #1151 or #62205 or
#62535
•Decalcifying Tablets: #61848
•Grand Aroma Coffee Beans: #921

O) Using the
frothXpress
PLUS system
The frothXpress PLUS
is separately available
for the F9.This system
siphons milk and
automatically produces
preprogrammed
amounts of hot frothed
or hot steamed milk
right into your cups,
never wasting any milk!
1. Disconnect the Dual-
Frother PLUS from the
steam nozzle (turn to
loosen and pull down
to remove).
2. Fill milk container with milk and assemble milk container
(see above). Attach the frothXpress to the steam nozzle.
Attach the milk container to the frothXpress (see above).
Important:Make sureall parts are connected tightly, other
wise siphoning does not work.
3. Set the dial to the (–) minus sign (12 o’clock) of the frothing
range for cappuccino or to the (–) minus sign (6 o’clock)
of the steaming range for latte.
4. Place cup underneath the frother.
5. Push the STEAM button. The button’s red light starts
blinking. YOUR MACHINE IS HEATING.After ~ 20 sec.:
SELECT PRODUCT.
6. Push the STEAM button again. STEAM PORTION.The F9
will create hot frothed or steamed milk right in your cup .
When you have enough milk in your cup push the STEAM
button to stop.
7. If you like morefrothed milk push the STEAM button again.
8. For hotter milk in either position move the dial more
towards the (+) plus symbols.
(The extra long hose lets you siphon milk from any carton
without using the special milk container.)
Tip:Use Chocolate milk to make great Hot Chocolate!
P) Cleaning the frothXpress PLUS system
Should be done right after use, takes less than 30 seconds.
• Store the milk container in the refrigerator and remove the
frothXpress from the steam nozzle.
• Drop the hose and the frothXpress in a cup of hot water.
This will push out any milk residue and prevents milk from
hardening inside the system.
•Place a cup underneath the steam nozzle and push the
HOT WATER button for three seconds.
•Replace frothXpress system.
1
2
3
frothXpress
Plus
attached
Milk
Container
Assembly
Frothing
range
Steaming
range
Steam only
no
siphoning
DIAL
+
+
_
_