JVC KD-AV7100 Guide

1
l
c
KD-AV7100
Installation/Connection Manual
This unit is designed to operate on 12 V DC, NEGATIVE
ground electrical systems. If your vehicle does not have
this system, a voltage inverter is required, which can be
purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location
where;
– it may obstruct the steering wheel and gearshift lever
operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air
bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the
steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving. It
may lead to carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to
look around carefully or you may be involved in a traffic
accident.
• If the parking brake is not engaged, the following warning
appears on the monitor, and no playback picture will be
shown.
CAUTION!!!
IT’S UNLAWFUL TO OPERATE A VEHICLE WHILE
VIDEO IS DISPLAYED IN THE DRIVERS VIEWING
AREA
ENGAGE EMERGENCY BRAKE TO ENJOY VIDEO
– This warning appears only when the parking brake lead
is connected to the parking brake system built in the car.
Notes on electrical connections:
•Replace the fuse with one of the specified rating. If the
fuse blows frequently, consult your JVC car audio dealer.
•It is recommended to connect speakers with a maximum
power of more than 50 W (both at the rear and at the
front, with an impedance of 4 Ω to 8 Ω).
•To prevent short circuits, cover the terminals of the
UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
o
Remote controller
Parts list for installation and connection
The following parts are provided for this unit. If anything is missing, contact your dealer immediately.
a
Main unit
0508MNMMDWSKP
EN
©2008 Victor Company of Japan, Limited
b
Sleeve
c
Trim plate
LVT1824-006D
[A]
j
Mounting bolt
d
Power cord
l
Handles
k
j
b
c
Do the required electrical
connections.
Bend the appropriate tabs to
hold the sleeve firmly in place.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as illustrated so
that the unit can be removed.
k
Rubber cushion
f
Special cable for iPod
e
Parking brake lead
n
Cleaning cloth
Heat sink
g
Round head screw
(M5 x 5 mm)
i
Tapping screw
m
Stay
When shipped from the factory,
the battery is installed in the
remote controller.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in
common?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in
common?
• This unit does not work at all.
* Have you reset your unit?
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to your
specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer
or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
h
Round head screw
(M4 x 2.5 mm)
KD-AV7100A_Install.indb 1KD-AV7100A_Install.indb 1 08.12.8 10:53:41 AM08.12.8 10:53:41 AM

2
b
g/i
j
m
g/h
g/h
50˚
33
136
2.5
43
110˚
167
44
Install the unit at an angle of less than 30˚, taking it into
account that the monitor would eject when in use (see
below).
Required space for the monitor ejection
Unit: mm
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
When using the stay
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
Fire wall
Dashboard
Use the supplied screws
For No.1 – 4
For No.5 – 9
M4 x 2.5 mm
M5 x 5 mm
Note :
When installing the unit on the mounting bracket, make sure to use the
supplied screws. Using other screws (than supplied ones) may damage the unit.
Bracket *1
Pocket
Lock nut *1
Washer *1
Bend the supplied stay.
*1Not included for this unit.
1234
567 89
KD-AV7100A_Install.indb 2KD-AV7100A_Install.indb 2 08.12.8 10:53:49 AM08.12.8 10:53:49 AM

KD-AV7100
PARKING
2
1
2
3
4
5
8
6
7
1
3
A
B
C
A
OE REMOTE
PARKING
AV OUT
SUB WOOFER
CENTER
FRONT
REAR
CAMERA
AV IN
B
iPod
ILLUMI
REVERSE
REMOTE
ACC
MEMORY
GND
P.ANTENNA
FRONT L+ FRONT L– FRONT R+ FRONT R– REAR L+ REAR L– REAR R+ REAR R–
3
Connect the parking brake lead to the parking brake system built in the car.
To metallic body or chassis of the car
Parking brake switch (inside the car)
Parking brake Parking brake lead (light green)
Crimp connector
(not supplied)
A
Parking brake lead (supplied)
Connecting the parking brake lead
10 A fuse
Ignition switch
Fuse block
White with
black stripe White Gray with black
stripe
Gray Green with black
stripe
Green Purple with black
stripe
Purple
Right speaker (front) Left speaker (rear) Right speaker (rear)
To a live terminal in the fuse block connecting to the car
battery (bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
For dimmer function. See page 11 of the INSTRUCTIONS.
Black
Yellow *4
Red
Blue with white stripe
Orange with white stripe
Purple with white stripe
A
: See the diagram below.
ABC
: See each diagram on page 4.
*3
Left speaker (front)
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.
3Finally connect the wiring harness to the unit.
To automatic antenna if any (250 mA max.)
Blue
To the remote lead of other equipment (200 mA max.)
To metallic body or chassis of the car *3
*2
To the reverse lamp lead (see
B
on page 4)
*2Not used for this unit.
*3Not included for this unit
*4
Before checking the operation of this unit
prior to installation, this lead must be
connected, otherwise power cannot be
turned on.
KD-AV7100A_Install.indb 3KD-AV7100A_Install.indb 3 08.12.8 10:53:49 AM08.12.8 10:53:49 AM

KD-AV7100
REVERSE
L
R
L
R
L
R
L
R
CAMERA
AV IN
AV OUT
*7
4
KD-AV7100
You can connect amplifiers to upgrade surround system in the car compartment.
• Connect the amplifiers to 5.1-ch analog discrete output plugs to enjoy multi-channel source.
• After you have connected the center speaker, make sure to activate the center speaker; otherwise, no sound comes out of the connected center speaker, see page 43 of the
INSTRUCTIONS.
• Disconnect the speakers from the unit, and connect them to the amplifier. Leave the speaker leads of the unit unused.
*5Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place
uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure
to do so may cause damage to the unit.
Subwoofer
Rear speakers
Center speaker
Front speakers
Navigation System or playback source
Connecting the audio/video cords
JVC Amplifier
JVC Amplifier
JVC Amplifier
JVC Amplifier
A
*6Audio/video cords (not supplied)
*7Required only when connecting a rear view camera to CAMERA plug.
*8When using a monitor other than KV-MR9010, use the monitor which can switch the color
system (NTSC/PAL) automatically.
To reverse lamp
Reverse lamp lead
To car battery
Reverse lamps
Connecting the external amplifiers
*6
*5
• You can supply the power to the amplifiers by
connecting the remote leads (blue with white stripe)
of this unit and amplifiers. (To connect more than one
amplifier using the remote leads, Y-connectors need to
be separately purchased.)
KD-AV7100
Remote lead (Blue with white stripe)
Y-connector (not supplied
for this unit)
Remote lead
JVC Amplifier
To the remote lead of other
equipment
*6
*5
*5
*5
KD-AV7100
iPod
B
C
KV-CM1
Rear view camera (not supplied)
KV-MR9010*8
9-INCH WIDESCREEN MONITOR (not supplied)
KS-HP2
Cordless headphones
(not supplied)
Connecting an Apple iPod
Apple iPod
You can connect an iPod to this unit using the supplied
special cable for iPod.
• iPod is a trademark of Apple Inc., registered in the
U.S. and other countries. Special cable for iPod
KD-AV7100A_Install.indb 4KD-AV7100A_Install.indb 4 08.12.8 10:53:50 AM08.12.8 10:53:50 AM