JVC KD-BT22 User manual

ENGLISH
KD-BT22
CD RECEIVER KD-BT22
For canceling the display demonstration, see page 5.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0528-003A
[UT]
Cover_KD-BT22_003A_f.indd 1Cover_KD-BT22_003A_f.indd 1 1/9/08 11:49:03 AM1/9/08 11:49:03 AM

ENGLISH
2
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLA 1 LA ER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUT IDE THE UNIT.
[European Union only]
Warning:
If you need to operate the unit while driving, be sure to
look around carefully or you may be involved in a traffic
accident.
Caution:
If the temperature inside the car is below 0°C, the
movement of animation and text scroll will be halted
on the display to prevent the display from being
blurred. appears on the display.
When the temperature increases, and the operating
temperature is resumed, these functions will start
working again.
Caution on volume setting:
Digital devices (CD/U B) produce very little noise
compared with other sources. Lower the volume before
playing these digital sources to avoid damaging the
speakers by sudden increase of the output level.
For sa ety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• top the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
EN02-07_KD-BT22_001A_1.indd 2EN02-07_KD-BT22_001A_1.indd 2 12/12/07 12:02:42 PM12/12/07 12:02:42 PM

ENGLISH
3
How to reset your unit
• Your preset adjustments will also be erased (except the
registered Bluetooth device, see pages 13 and 14).
How to orcibly eject a disc
“Please Eject” appears on the display.
• Be care ul not to drop the disc when it ejects.
• I this does not work, reset your unit.
CONTENTS
INTRODUCTIONS
Preparation .................................................. 5
OPERATIONS
Basic operations ........................................... 6
• Using the control panel ............................... 6
• Using the remote controller (RM-RK50) ...... 7
Listening to the radio ................................... 8
Disc operations ............................................. 10
Listening to the U B device .......................... 12
Using the Bluetooth
® devices ....................... 13
• Using the Bluetooth cellular phone ............ 15
• Using the Bluetooth audio player ............... 18
EXTERNAL DEVICES
Listening to the CD changer ......................... 19
Listening to the iPod .................................... 20
Listening to the other external
components .............................................. 22
SETTINGS
electing a preset sound mode .................... 23
General settings — P M .............................. 26
Bluetooth settings ....................................... 30
Title assignment .......................................... 31
REFERENCES
More about this unit .................................... 32
Troubleshooting ........................................... 37
Maintenance ................................................ 41
pecifications ............................................... 42
EN02-07_KD-BT22_001A_1.indd 3EN02-07_KD-BT22_001A_1.indd 3 12/12/07 12:02:44 PM12/12/07 12:02:44 PM

ENGLISH
4
Detaching the control panel
Attaching the control panel
How to use the M MODE and SEL
buttons
If you use M MODE or SEL (select), the display and some
controls (such as the number buttons,
4 /¢ buttons, 5/∞ buttons, and the
control dial) enter the corresponding control mode
Ex : When you press number button 1 after pressing
M MODE, to operate the FM tuner
To use these controls for original functions, press
M MODE again
• However, pressing SEL makes the unit enters a
different mode
• Waiting for about 15 seconds without pressing any of
these buttons will automatically cancels the control
Avoid touching the connectors
EN02-07_KD-BT22_001A_f.indd 4EN02-07_KD-BT22_001A_f.indd 4 1/2/08 11:07:04 AM1/2/08 11:07:04 AM

ENGLISH
5INTRODUCTIONS
Preparation
Cancel the display demonstration and set the clock
• ee also pages 26 and 27.
1Turn on the power.
2Enter the PSM settings.
3Cancel the display demonstrations
elect “Demo,” then “Off.”
Set the clock
elect “Clock Hr” (hour), then adjust the hour.
elect “Clock Min” (minute), then adjust the minute.
elect “24H/12H,” then “24Hours” or “12Hours.”
4Finish the procedure.
Changing the display in ormation and pattern
When the power is turned off: Check the current clock time
Ex.: When tuner is selected as the source
ource operation display
• If a station has been assigned a title, station
title appears after about 5 seconds.
• To assign a title to a station, see pages 31 and
32.
Audio level meter display
(see “LevelMeter” on page 26)
EN02-07_KD-BT22_001A_1.indd 5EN02-07_KD-BT22_001A_1.indd 5 12/12/07 12:02:45 PM12/12/07 12:02:45 PM

ENGLISH
6
Basic operations
Using the control panel
9 • Select/adjust the sound mode.
• Enter the PSM settings [Hold].
p • TUNER: Select preset station.
• CD/USB/CD-CH: Select folder/track/disc (for D
changer).
• USB-iPod: Select preset top menu items.
• Bluetooth: Dial preset phone number *2.
q • Enter functions mode.
• Bluetooth: Activate Voice Dialing [Hold].
w hange the display information and pattern.
e • TUNER: Select the bands.
• USB-iPod: Start/pause playback.
• BT-AUD O: Start/pause playback.
*1 You cannot select these sources if they are not ready
or not connected.
*2 For storing preset phone number, see page 17.
1 • TUNER: Select preset station.
• CD/USB/CD-CH: Select folder.
• USB-iPod: Enter the main menu [Hold].
• iPod: Enter the main menu/Pause playback/
onfirm selection.
2 • Turn on the power.
• Turn off the power [Hold].
• Attenuate the sound (if the power is on).
• Bluetooth: Switch the conversation media
during a phone call conversation.
3 Display window
4 • Enter/exit Bluetooth menu.
• Display the dialed list [Hold].
5 Flip down the control panel.
• To eject the disc, flip down the control panel
then press 0 on the unit.
6 AUX (auxiliary) input jack
7 • TUNER: Search for station.
• CD/USB/CD-CH/USB-iPod/iPod: Select track.
• BT-AUD O: Reverse skip/forward skip.
8 • Volume control [Turn].
• Select the source [Press] .
TUNER = CD *1 = USB *1 (or USB-iPod) *1
= CD-CH *1/iPod *1 (or EXT N) = BT-AUD O
= AUX N = (back to the beginning)
EN02-07_KD-BT22_001A_f.indd 6EN02-07_KD-BT22_001A_f.indd 6 1/2/08 11:07:35 AM1/2/08 11:07:35 AM

ENGLISH
7OPERATIONS
Installing the lithium coin battery (CR2025)
Caution:
Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
If the effectiveness of the remote controller
decreases, replace the battery
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bri ht li ht
(direct sunli ht or artificial li htin ).
Warning (to prevent accidents and damage):
• Do not install any battery other than CR2025 or its
equivalent.
• Do not leave the remote controller in a place (such
as dashboards) exposed to direct sunli ht for a lon
time.
• Store the battery in a place where children cannot
reach.
• Do not rechar e, short, disassemble, heat the battery,
or dispose of it in a fire.
• Do not leave the battery with other metallic materials.
• Do not poke the battery with tweezers or similar tools.
• Wrap the battery with tape and insulate when
throwin away or savin it.
Using the remote controller (RM-RK50)
Remote sensor
1 • Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
• Switches the conversation media durin a phone
call conversation.
2 • Chan es the FM/AM bands with 5 U.
• Chan es the preset stations with D ∞.
• Chan es the folder of the MP3/WMA/AAC/WAV.
• While playin an MP3 disc on an
MP3-compatible CD chan er:
– Chan es the disc if pressed briefly.
– Chan es the folder if pressed and held.
• While listenin to an Apple iPod:
Connected to KS-PD100:
– Pauses or resumes playback with D ∞.
– Enters the main menu with 5 U.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selectin buttons.)*
* 5 U : Returns to the previous menu.
D ∞ : Confirms the selection.
Connected to the USB cable:
– Enter the main menu if pressed and held.
– Select the desired menu if pressed briefly.
– Fast skip in every layer of the main menu if
pressed and held.
3 Adjusts the volume level.
4 Selects the sound mode (iEQ: intelli ent equalizer).
5 Selects the source.
6 For Bluetooth cellular phone:
– Answers calls if pressed briefly.
– Rejects calls if pressed and held.
– Holds calls if pressed briefly durin phone call
conversation.
Continued on the next page
EN02-07_KD-BT22_001A_f.indd 7EN02-07_KD-BT22_001A_f.indd 7 1/2/08 3:41:24 PM1/2/08 3:41:24 PM

ENGLISH
8
Listening to the radio
1Select “TUNER.”
2Select the bands.
3Search for a station to listen—Auto Search.
Manual Search: Hold either one of the buttons until “M” lights up on the display, then
press it repeatedly.
• When receiving an FM stereo broadcast ith sufficient signal strength, lights up
on the display.
7 • Searches for stations if pressed briefly.
• Fast-for ards or reverses the track if pressed and
held.
• Changes the tracks if pressed briefly.
3 Exit from the setting.
• While listening to an iPod (in menu selecting
mode):
Connected to S-PD100:
– Selects an item if pressed briefly. (Then, press
D ∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
Connected to the USB cable:
– Start play back the selected folder directly if
pressed and held.
• Reverse skip/for ard skip for Bluetooth audio.
When an FM stereo broadcast is
hard to receive
1
2
Reception improves, but stereo effect ill be lost.
• lights up on the display.
EN08-17_KD-BT22_001A_1.indd 8EN08-17_KD-BT22_001A_1.indd 8 12/17/07 11:20:42 AM12/17/07 11:20:42 AM

ENGLISH
9OPERATIONS
FM station automatic presetting
— SSM (Strong-station Sequential
Memory)
You can preset up to six stations for each band.
1 While listening to a station...
2
3
Local FM stations ith the strongest signals are
searched and stored automatically in the selected
FM band.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
Using the number buttons
1
2
3
Using the Preset Station list
• When is sho n on the display, you can
move back to the previous screen by pressing number
button 3.
1 Follow steps 1 and 2 of “Using the number
buttons” on the left column.
• By holding 5 / ∞, the Preset Station List ill
also appear (go to step 4).
2
3 Display the Preset Station List.
4 Select the preset number you want to store
into.
• You can move to the lists of the other FM bands
by pressing number button 5 ( ) or
6 ( ) repeatedly.
5 Store the station.
Preset number flashes for a hile.
Continued on the next page
EN08-17_KD-BT22_001A_1.indd 9EN08-17_KD-BT22_001A_1.indd 9 12/12/07 12:02:58 PM12/12/07 12:02:58 PM

ENGLISH
10
Prohibiting disc ejection
To cancel the prohibition, repeat the same
procedure.
Listening to the preset station on the Preset Station List
1 Display the Preset Station List, then select the preset station you want to listen to.
2 Change to the selected station.
*1
Disc operations
All tracks ill be played repeatedly until you change the
source or eject the disc.
To stop play and eject the disc
• Press SOURCE to listen to another playback source.
Pressing (or holding) the follo ing buttons allo s you
to...
[Press] Select track
[Hold] Reverse/fast-for ard
track
MP3/WMA/AAC: Select folder
(Number buttons) *2
Locate particular folder *3
(for MP3/WMA/AAC) or track
directly
*1 By holding either one of the buttons, you can display
the Folder List (see page 11).
*2 Press to select number 1 to ; hold to select number
7 to 12.
*3 It is required that folders be assigned with 2-digit
numbers at the beginning of their folder names—01,
02, 03, and so on.
EN08-17_KD-BT22_001A_1.indd 10EN08-17_KD-BT22_001A_1.indd 10 12/12/07 12:02:59 PM12/12/07 12:02:59 PM

ENGLISH
11OPERATIONS
4 Select an item.
• You can move to the other lists by pressing
number button 5 ( ) or 6 ( )
repeatedly.
5 Change to the selected item.
A If File List is selected
The list disappears and playback
starts.
B If Folder List is selected
• If the current folder is selected, File List
appears, then repeat steps 4 and 5 A to
start playback.
• If another folder is selected, playback starts
from the 1st file of the selected folder.
Ex.: When “File” is selected in step 3
After pressing M MODE, press the follo ing buttons to...
Skip 10 tracks
MP3/WMA/AAC: Within the same
folder
Repeat Track:
Repeat current track
Repeat Folder:
MP3/WMA/AAC: Repeat current
folder
Random Folder:
MP3/WMA/AAC: Randomly play all
tracks of current folder, then tracks
of next folders
Random Disc:
Randomly play all tracks
• You can also cancel the playback mode by selecting
“Off” or press number button 4 ( ).
Selecting a folder/track on the list
(only for MP3/WMA/AAC file)
• When is sho n on the display, you can
move back to the previous screen by pressing number
button 3.
1
2 Select “LIST.”
3 Select the list type.
EN08-17_KD-BT22_001A_1.indd 11EN08-17_KD-BT22_001A_1.indd 11 12/12/07 12:02:59 PM12/12/07 12:02:59 PM

ENGLISH
12
If a USB device has been attached...
Playback starts from where it has
been stopped previously.
• If a different USB device is
currently attached, playback starts
from the beginning.
To stop play and detach the USB device
Straightly pull it out from the unit.
• Press S URCE to listen to another playback source.
You can operate the USB device in the same way you
operate the files on a disc. (See pages 10 and 11.)
• You can listen to WAV files by following the MP3/
WMA/AAC files operations listed on pages 10 and 11.
Cautions:
• Avoid using the USB device if it might hinder your
safety driving.
• Do not pull out and attach the USB device repeatedly
while “Reading” is shown on the display.
• Do not start the car engine if a USB device is
connected.
• This unit may not be able to play the files depending
on the type of USB device.
• peration and power supply may not work as
intended for some USB devices.
• You cannot connect a computer to the USB cable from
the rear of the unit.
• Make sure all important data has been backed up to
avoid losing the data.
• Do not leave a USB device in the car, expose to direct
sunlight, or high temperature to avoid deformation
or cause damages to the device.
• Some USB devices may not work immediately after
you turn on the power.
• For more details about USB operations, see pages 34
and 35.
Listening to the USB device
You can connect a USB mass storage class device such as a USB memory, Digital Audio Player *1, portable HDD, etc. to
the unit.
• You can also connect an Apple iPod to the USB cable from the rear of the unit. For details of the operations, see
pages 20 and 21.
This unit can play MP3/WM /WM -DRM10 *1/ C *2/W V tracks stored in a USB device.
*1 You can connect both MTP (Media Transfer Protocol) devices and USB mass storage class devices. See also page 3 .
*2 This unit can play back AAC files encoded using iTunes. This unit cannot play back FairPlay-encrypted files.
All tracks will be played repeatedly until you change the source or detach the USB device.
USB cable from the rear of the unit.
USB memory
EN08-17_KD-BT22_001A_1.indd 12EN08-17_KD-BT22_001A_1.indd 12 12/18/07 9:37:20 AM12/18/07 9:37:20 AM

ENGLISH
13OPERATIONS
Using the Bluetooth ® devices
Bluetooth is a short-range wireless radio
communication technology for the mobile device such
as mobile phones, portable PCs, and other devices. The
Bluetooth devices can be connected without cables and
communicate with each other.
• Refer to the list included in the box) to see the
countries where you may use the Bluetooth®
function.
Bluetooth profile
This unit supports the following Bluetooth profiles;
HFP Hands-Free Profile) 1.5
OPP Object Push Profile) 1.1
A2DP Advanced Audio Distribution Profile) 1.2
AVRCP Audio/Video Remote Control Profile) 1.3
Features
You can operate Bluetooth devices through the unit as
follows:
• Receiving a call
• Making a call—from phone book, from call history
dialed number/received call), by dialing number, by
preset numbers, by voice command
• Informing you of the arrival of a text message
• Play back a Bluetooth audio player
Refer also to the instructions supplied with the
Bluetooth device.
Connecting a Bluetooth device for
the first time
Pairing and PIN code
When you connect a Bluetooth device to the unit
for the first time, make pairing between the unit
and the device. Pairing allows Bluetooth devices to
communicate with each other.
To make pairing, you may need to enter the PIN
Personal Identification Number) code of your Bluetooth
device you want to connect.
• Once the connection is established, it is registered in
the unit even if you reset the unit. Up to five devices
can be registered in total.
• Only one device for Bluetooth phone and one for
Bluetooth audio can be connected at a time.
• To use the Bluetooth function, you need to turn on
Bluetooth function of the device.
Preparation: Operate the device to turn on its
Bluetooth function.
• When is shown on the display, you can
move back to the previous screen by pressing number
button 3.
1 While listening to a source...
2 Select Device.”
3 Select New Pairing.”
Continued on the next page
EN08-17_KD-BT22_001A_f.indd 13EN08-17_KD-BT22_001A_f.indd 13 1/2/08 11:10:00 AM1/2/08 11:10:00 AM

ENGLISH
14
4 Enter a PIN (Personal Identification Number)
code to the unit.
• You can enter any number you like 1-digit to
16-digit number). [Initial: 0000]
• To enter a PIN code less than 4-digit, firstly
delete the initial PIN code 0000) by pressing
number button 5 ) .
* Some devices have their own PIN code. Enter the
specified PIN code to the unit.
1 Move to the next or previous) number
position.
2 Select a number.
3 Repeat steps 1 and 2 until you finish
entering a PIN code.
4 Confirm the entry.
5 Operate the target Bluetooth device, (while
Open...” is flashing on the display).
On the device to be connected, enter the same PIN
code you have just entered for this unit.
“Connecting...” flashes, then “Pairing Ok” or
“Connected [Device Name]” appears on the display
when the connection is established. Now you can
use the device through the unit.
appears when the connection is established.
The device remains registered even after you
disconnect the device. Use “Cnnct Phone“ or
“Cnnct Audio” or activate “Auto Cnnct”) to
connect the same device from next time on. See the
following and pages 30 and 31.)
Deleting a registered device
Perform steps 1 and 2 on page 13, then...
1 Select Del Pairing.”
2 Select a device you want to delete.
3 Delete the selection.
• Press number button 3 to select “No” or return to
step 1.
Connecting a registered device
Perform steps 1 and 2 on page 13, then...
1 Select Cnnct Phone” or Cnnct Audio.”
2 Select a device you want.
“Connecting...” flashes, then “Connected and
device name)” appears on the display when the
device is connected.
EN08-17_KD-BT22_001A_f.indd 14EN08-17_KD-BT22_001A_f.indd 14 1/2/08 11:10:02 AM1/2/08 11:10:02 AM

ENGLISH
15OPERATIONS
Continued on the next page
You can set the unit to connect the Bluetooth device
automatically when the unit is turned on. See
“Auto Cnnct” on page 30.)
Disconnecting a device
Perform steps 1 and 2 on page 13, then...
Select Discn Phone” or Discn Audio.”
“Disconnecting...” flashes, then “Disconnected and
device name)” appears on the display when the device
is disconnected.
Using the Bluetooth cellular
phone
Making a call
You can make hands-free calls using the unit.
The sounds comes out from the connected speakers.
• When appears on the display, you can
move back to the previous display by pressing
number button 3.
1
2 Select Call.”
3 Select the method to make a call.
• Dialed *: Shows the list of the phone numbers
you have dialed. Go to the following step.
• Received *: Shows the list of the received calls.
Go to the following step.
• Phonebook: Shows the name/phone number of
the phone book of the unit. Go to the following
step. To copy the phone book memory, see page
17.
• Preset: Shows the list of preset numbers. Go to
the following step. To preset numbers, see page
17.
• Dial Number: Shows the phone number entry
screen. See “How to enter phone number” on
page 16.
• Voice Dial Only accessible when the connected
cellular phone has the voice recognition system):
Speak the name registered words) you want to
call.
* Displays only when the dialed or received number
is made through the unit.
4 Select the name/phone number/preset
number you want to call.
• When the sound is stopped or interrupted during the
use of a Bluetooth device, turn off, then turn on the
unit.
– If the sound is not yet restored, connect the device
again. See “Connecting a registered device” on
page 14.)
The built-in microphone is
behind this corner of the unit.
EN08-17_KD-BT22_001A_f.indd 15EN08-17_KD-BT22_001A_f.indd 15 1/2/08 11:10:02 AM1/2/08 11:10:02 AM

ENGLISH
16
When a call comes in....
The source is automatically changed to “Bluetooth.”
• Phone number appears if acquired).
When Auto Answer” is activated....
The unit answers the incoming calls automatically, see
pages 30 and 31.
• When “Auto Answer” is deactivated, press any
button except /control dial) to answer the
incoming call.
• You can adjust the microphone volume level see
pages 30 and 31).
To end the call or reject an incoming call
Hold any button except /control dial).
• When “Auto Answer” is set to “Reject,” the unit
rejects any incoming calls.
Answering a waiting call
If your cellular phone is equipped with the call waiting
function, you can put the current call on hold and
answer the waiting call.
Press any button except /control dial).
• To restore the on-hold call, press any button except
/control dial) again.
• When you end one call, you can connect to the other.
When a text message comes in....
If the cellular phone is compatible with Text Message
and “MSG Notice” is set to “On” see pages 30 and 31),
the unit rings and “Received Message” appears on the
display to inform you of the message arrival.
• You cannot edit or send a message through the unit.
How to enter phone number
How to delete phone number
1
2 Select Call.”
3 Display the list of phone numbers using one
of the dialing method (see step 3 of Making
a call” on page 15).
4 Select the name/phone number you want to
delete.
5 Delete the selection.
• Press number button 6 ) to delete all
the listed numbers in step 3.
Select a number.
Move the entry position.
Confirm the entry.
EN08-17_KD-BT22_001A_f.indd 16EN08-17_KD-BT22_001A_f.indd 16 1/2/08 11:10:03 AM1/2/08 11:10:03 AM

ENGLISH
17OPERATIONS
How to copy phone book
You can copy the phone book memory of a cellular
phone into the unit.
• When is sho n on the display, you can
move back to the previous screen by pressing number
button 3.
1
2 Select “Settings.”
3 Select “PhoneBook.”
4 Enter the PIN code both for this unit and
Bluetooth phone.
• See step 4 of page 14.
5
Operate the target cellular phone. (While
“Receiving 00/50” appears on the display.) Enter
the same PIN code (as entered in step 4) on the
cellular phone, then transfer the phone book
memory to the unit. (Refer to the Instructions
manual supplied ith your cellular phone.)
Presetting the phone number
You can preset up to six phone numbers.
• When is sho n on the display, you can
move back to the previous screen by pressing number
button 3.
1 Display the phone number you want to
preset by using one of the “Call” items.
2 Select a phone number.
You can also enter a ne phone
number (see also “Ho to enter
phone number” on page 16) to store.
3 Select a preset number to store.
To call a preset number
While in Bluetooth audio....
• You can also call a preset number using “Preset” of
the “Call” items (see page 15).
Switching conversation media (the unit/
cellular phone)
During a phone call conversation....
Then, continue your conversation
using the other media.
Continued on the next page
EN08-17_KD-BT22_001A_1.indd 17EN08-17_KD-BT22_001A_1.indd 17 12/12/07 12:03:04 PM12/12/07 12:03:04 PM

ENGLISH
18 OPERATIONS
Using the Bluetooth audio player
• Operations and display indications differ depending on their availability on the connected audio player.
Select “BT-AUDIO.”
If playback does not start automatically, operate the Bluetooth audio player to start playback.
[Press] everse skip/forward skip
[Hold] everse search/forward
search
Select group/folder
Start/pause playback
• efer also to pages 14 and 15 for connecting/
disconnecting/deleting a registered device.
Bluetooth Information
If you wish to receive more information about
Bluetooth, visit the following JVC web site: <http://
www.jvc-victor.co.jp/english/car/>.
After pressing M MODE, press the following buttons to...
Repeat Track
epeat current track
Repeat All
epeat all tracks
Repeat Group
epeat all tracks of current group
Random All
andomly play all tracks
Random Group
andomly play all tracks of the
current group
• You can also cancel the playback mode by selecting
“Off” or press number button 4 ( ).
EN18-23_KD-BT22_001A_1.indd 18EN18-23_KD-BT22_001A_1.indd 18 12/12/07 12:03:15 PM12/12/07 12:03:15 PM

ENGLISH
19
EXTERNAL DEVICES
Listening to the CD changer
It is recommended to use a JVC MP3-compatible CD changer with your unit. You can connect a CD changer to the
CD changer ack on the rear of the unit.
• You can only play conventional CDs (including CD Text) and MP3 discs.
Preparation: Make sure “Changer” is selected for the external input setting, see page 28.
1Select “CD-CH.”
2Select a disc to start playing.
[Press] For selecting disc number 1 – 6.
[Hold] For selecting disc number 7 – 12.
[Press] Select track
[Hold] Reverse/fast-forward track
MP3: Select folders
* By holding either one of the buttons, you can display
the Disc List (see page 11).
To select a disc/folder/track on the list
See “Selecting a folder/track on the list (only for MP3/
WMA/AAC file)” on page 11.
Select “Disc” in step 3 to display the Disc List of the CD
changer.
*
After pressing M MODE, press the following buttons to...
Skip 10 tracks
MP3: Within the same folder
epeat Track:
Repeat current track
epeat Folder:
MP3: Repeat all tracks of current
folder
epeat Disc:
Repeat all tracks of the current disc
andom Folder:
MP3: Randomly play all tracks of
the current folder, then tracks of the
next folder
andom Disc:
Randomly play all tracks of current
disc
andom All:
Randomly play all tracks of the discs
in the magazine
• You can also cancel the playback mode by selecting
“Off” or press number button 4 ( ).
EN18-23_KD-BT22_001A_f.indd 19EN18-23_KD-BT22_001A_f.indd 19 1/9/08 4:58:36 PM1/9/08 4:58:36 PM

ENGLISH
20
Listening to the iPod
You can play songs in an Apple iPod by:
– Connecting it with the USB cable supplied with your iPod to the USB cable from the rear of the unit.
– Connecting the nterface adapter for iPod, KS-PD100 (separately purchased) to the CD changer jack on the rear of
the unit.
Preparation: Make sure “Changer” is selected for the external input setting, see page 28.
• You can control playback from the unit.
• Disconnecting the iPod will stop playback. Press SOURCE to listen to another playback source.
• For details, refer also to the manual supplied for your iPod.
Caution:
• Avoid using the iPod if it might hinder your safety while driving.
• Make sure all important data has been backed up to avoid losing the data.
1
—
Connect an iPod to the USB cable or through KS-PD100.
Playback starts automatically from where it had been paused previously.
• f an iPod has been connected, press SOURCE to select “USB-iPod” or “iPod” as
the playback source.
2Select a track.
3—Adju t the volume and ound a you want. (See page 23 – 25.)
Playback control from the unit
Button For iPod connected through KS-PD100 For iPod connected to the USB cable
[Press] Go to the next or previous track
[Hold] Fast-forward or reverse the track
during playback
[Press] Go to the next or previous track
[Hold] Fast-forward or reverse the track
during playback
[Press] Enter main menu when you press 5.
Pause/resume playback when ∞ is
pressed.
[Hold] Enter main menu
[Press] Go to the top menu of “Playlists,”
“Artists,” “Albums,” “Songs,”
“Podcasts,” “Genres,” “Composers,” or
“Audiobooks” in the main menu.
• Pressing the number buttons (1 – 6)
or holding 1 (7) and 2 (8) can also
select the preset top menus.
— [Press] Pause/resume playback.
EN18-23_KD-BT22_001A_1.indd 20EN18-23_KD-BT22_001A_1.indd 20 12/17/07 11:28:10 AM12/17/07 11:28:10 AM