JVC KD-G465 Guide

KD-G465
Installation/Connection Manual
GET0256-008A
[UT]
1104DTSMDTJEIN
EN, CT
ENGLISH
This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
J
Handles
F
Washer (ø5)
G
Lock nut (M5)
H
Mounting bolt (M5 x 20 mm)
I
Rubber cushion
A / B
Hard case/Control panel
D
Trim plate
E
Power cord
Parts list for installation and connection
The following parts are provided for this receiver.
After checking them, please set them correctly.
1
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this receiver correctly, have it installed by a qualified
technician.
Do the required electrical connections.
*1 When you stand the receiver, be
careful not to damage the fuse on
the rear. Bend the appropriate tabs to hold the
sleeve firmly in place.
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• Receiver becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This receiver does not work at all.
* Have you reset your receiver?
C
Sleeve
K
Remote
controller
L
Battery
Removing the receiver /
Before removing the receiver, release the rear section.
Insert the two handles, then
pull them as illustrated so
that the receiver can be
removed.
When installing the receiver without using the sleeve / When using the optional stay /
Note : When installing the receiver on the mounting bracket, make
sure to use the 8 mm-long screws. If longer screws are used,
they could damage the receiver.
Bracket*
Bracket*
* Not included for this receiver.
Flat type screws
(M5 x 8 mm)*
Pocket
Flat type screws
(M5 x 8 mm)*
Screw (option)
Stay (option)
Fire wall
Dashboard
Install the receiver at an
angle of less than 30˚.
PRECAUTIONS on power supply and speaker
connections:
• DO NOT connect the speaker leads of the power cord to
the car battery; otherwise, the receiver will be seriously
damaged.
• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.
In a Toyota for example, first remove the car radio and install the receiver in its place.
Install1-2_EN-CH[KD-G465].indd 1 11/18/04 7:11:24 PM

ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and
make all electrical connections before installing the receiver.
• Be sure to ground this receiver to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both
at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to prevent the speakers
from being damaged (see page 20 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED
leads with insulating tape.
• The heat sink becomes very hot after use. Be
careful not to touch it when removing this receiver.
Heat sink
2
ENGLISH
ATypical connections /
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in
color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the receiver.
BConnecting the external amplifier /
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so
that it can be controlled through this receiver.
• Disconnect the speakers from this receiver, connect them to the amplifier. Leave the
speaker leads of this receiver unused.
Signal cord (not supplied for this receiver)
Front speakers
Rear speakers
JVC Amplifier
KD-G465
Remote lead Y-connector (not supplied for this receiver)
Remote lead (Blue with white stripe)
To the remote lead of other equipment or automatic antenna if any
*2 Before checking the operation of this receiver
prior to installation, this lead must be connected,
otherwise power cannot be turned on.
Line out (see diagram )
Rear ground
terminal
15 A fuse
Antenna terminal Black
Blue with white stripe
Red
Yellow*2
*1 Not included for this receiver
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Ignition switch
Fuse block
To an accessory terminal in the fuse block
To the automatic antenna if any (250 mA max.)
Left speaker (front) Right speaker (front) Left speaker (rear) Right speaker (rear)
PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black
stripe
*3 Firmly attach the ground wire to the metallic body
or to the chassis of the car—to the place not coated
with paint (if coated with paint, remove the paint
before attaching the wire). Failure to do so may
cause damage to the receiver.
To the remote lead of other equipment (200 mA max.)
Blue
To CD changer or another external component (see diagram )
CConnecting other external components /
CD changer /
JVC CD changer
Signal cord supplied for your CD changer
CAUTION /
• Before connecting the CD
changer, make sure that the
receiver is turned off.
External component /
CD changer jack
KS-U57*3
Signal cord (not supplied for this receiver) *3 Line Input Adapter KS-U57
(not supplied for this receiver)
External component
Install1-2_EN-CH[KD-G465].indd 2 11/19/04 3:15:24 PM