JVC KD-HDR40 User manual

ENGLISHESPAÑOLFRANÇAIS
For canceling the display demonstration, see page 4.
Para cancelar la demostración en pantalla, consulte la página 4.
Pour annuler la démonstration des affichages, référez-vous à la page 4.
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
LVT2088-001B
[J]
For customer Use:
Enter below the Model
No. and Serial No. which
are located on the top or
bottom of the cabinet. Retain
this information for future
reference.
Model No.
Serial No.
CD RECEIVER
RECEPTOR CON CD
RÉCEPTEUR CD
KD-HDR40

ENGLISH
2
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
Caution:
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
[European Union only]
Warning:
If you need to operate the unit while driving, be sure to
look around carefully or you may be involved in a traffic
accident.
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

ENGLISH
3
How to reset your unit
• Your preset adjustments will also be erased (except the
registered Bluetooth devices, see page 13).
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc to
avoid damaging the speakers by the sudden increase of
the output level.
How to forcibly eject a disc
• You can forcibly eject the loaded disc even if the disc is
locked. To lock/unlock the disc, see page 12.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
CONTENTS
Detaching the control panel......................... 3
Attaching the control panel ......................... 3
How to reset your unit ................................. 3
How to forcibly eject a disc........................... 3
Canceling the display demonstration........... 4
Setting the clock .......................................... 4
OPERATIONS
Basic operations........................................... 5
• Using the control panel............................... 5
• Using the remote controller (RM-RK50)...... 6
• Changing the display information .............. 8
Listening to the radio................................... 8
Disc operations............................................. 11
EXTERNAL DEVICES
Using the Bluetooth® devices ...................... 13
• Using the Bluetooth mobile phone............. 15
• Using the Bluetooth audio player ............... 16
Listening to the Satellite Radio .................... 17
Listening to the other external
components.............................................. 19
SETTINGS
Adjusting the sound..................................... 20
Bluetooth settings ....................................... 21
SET menu operations ................................... 22
REFERENCES
More about this unit .................................... 25
Troubleshooting........................................... 27
Maintenance................................................ 31
Specifications............................................... 32
[Hold]
Detaching the control panel
Attaching the control panel

ENGLISH
4
1Turn on the power.
2Call up the SET menu.
3
1Turn on the power.
2Call up the SET menu.
3Select “CLOCK.”
4Select “CLOCK SET.”
5Adjust the hour.
6Adjust the minute.
7Finish the procedure.
[Hold]
4Select “DEMO OFF.”
5
6Finish the procedure.
Canceling the display demonstration
[Turn]
(Initial setting) [Press]
[Press]
[Hold]
(Initial setting)
[Turn]
[Turn] [Press]
[Turn] [Press]
[Press]
[Turn] [Press]
Setting the clock

ENGLISH
5OPERATIONS
Basic operations
Using the control panel
6Loading slot
7Display window
8• Select the sound mode.
• Enter the Easy EQ setting menu [Hold].
9Change the display information.
pDetach the panel.
q• FM/AM/SIRIUS/XM: Search for station/channel.
• CD: Select track.
• BT PHONE/BT AUDIO: Select setting item/
registered device.
w• Enter LIST menu.
• Enter SET menu [Hold].
eReturn to the previous menu.
rRemote sensor
tAUX (auxiliary) input jack
*Also known as “Control dial” in this manual.
1• FM/AM:
– Select preset station.
– Search for HD Radio stations only [Hold].
• SIRIUS/XM: Select category.
• CD: Select folder.
• BT PHONE/BT AUDIO: Enter/go back to
previous Bluetooth menu.
2Eject disc.
3• Turn on the power.
• Turn off the power [Hold].
• Select the available sources (if the power is on).
4Enter playback mode menu.
5• Control the volume or select items [Turn].
• Confirm the selection [Press].
• CD: Pause/resume playback [Press].
– If you adjust the volume while paused,
playback will resume at minimum volume.
• Other source: Turn off the volume instantly
[Press].
*

ENGLISH
6
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
Replacing the lithium coin battery (CR2025)
When you use the remote controller for the first time,
remove the insulation sheet.
Caution:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
If the effectiveness of the remote controller
decreases, replace the battery.
Display window
1(Bluetooth) indicator
2MENU (menu) indicators— (setting menu),
(list menu)
3Tr (track) indicator
4Source display / Preset number / Track number /
Folder number
5Status of Bluetooth device
(Device number, [P: 1 – 5]; signal strength,
[: 0 – 3]*2; battery reminder, [ : 0 – 3]*2)
6ST (stereo) indicator
7HD (HD Radio™ broadcast) indicator
8HOLD (reception hold) indicator
9TAG (Tag information) indicator
pPlayback mode indicators— (random),
(repeat)
qDisc information indicators— (track/file),
(folder)
wMain display
*1Appears when another layer exists for the current
selection.
*2As the number increases, the signal/battery power
becomes stronger.
Using the remote controller (RM-RK50)
Remote sensor
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material—special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Insulation sheet
*1

ENGLISH
7OPERATIONS
1• Turns the power on if pressed briefly.
• Turns the power off if pressed and held.
• For discs: Pauses/resumes playback if pressed
briefly.
• For Other sources: Turns off the volume instantly
if pressed briefly.
2• Selects the preset radio station if pressed briefly.
• Searches for HD Radio stations only if pressed
and held.
• Changes the folder of the MP3/WMA.
• While listening to the Satellite (SIRIUS or XM)
Radio: Changes the categories.
3Adjusts the volume level.
4Selects the sound mode.
5Selects the source.
6For Bluetooth mobile phone:
– Answers calls if pressed briefly.
– Ends or rejects calls if pressed and held.
7• Searches for stations automatically if pressed
briefly.
• Searches for stations manually if pressed and
held.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the tracks if pressed briefly.
• While listening to the Satellite Radio:
– Changes the channels if pressed briefly.
– Changes the channels rapidly if pressed and
held.
• Reverse skip/forward skip for Bluetooth audio
player.
Warning (to prevent accidents and damage):
• Do not install any battery other than CR2025 or its
equivalent.
• Do not leave the remote controller in a place (such
as dashboards) exposed to direct sunlight for a long
time.
• Store the battery in a place where children cannot
reach.
• Do not recharge, short, disassemble, heat the battery,
or dispose of it in a fire.
• Do not leave the battery with other metallic
materials.
• Do not poke the battery with tweezers or similar
tools.
• Wrap the battery with tape and insulate when
throwing away or saving it.

ENGLISH
8
Changing the display information
• When the power is turned off: The current clock time is displayed for about 5 seconds.
• When the power is turned on: The display information of the current source changes as follows:
FM/AM Call Sign*1=Frequency =PTY (Program Type)*2=Text*3=Clock =(back to the
beginning)
CD • Audio CD/CD Text:
Disc title/performer*4=Track title*4=Current track number with the elapsed playing
time =Current track number with the clock time =(back to the beginning)
• MP3/WMA:
Album name/performer (folder name)*5=Track title (file name)*5=Current track
number with the elapsed playing time =Current track number with the clock time =(back
to the beginning)
SIRIUS/XM Category name =Channel name =Artist name =Composer name*6=Song/program
name/title =Clock =(back to the beginning)
*1Displayed only when a Call Sign is received.
*2When no program type (PTY) is received, “HD RADIO” appears for HD Radio broadcasting, and “ANALOG” appears for
conventional FM/AM broadcasting.
*3“NO TEXT” appears when no text is received.
*4If the current disc is an audio CD, “NO NAME” appears.
*5If an MP3/WMA le does not have Tag information or “TAG DISPLAY” is set to “TAG OFF” (see page 23),
folder name and le name appear.
*6Only for SIRIUS Satellite Radio.
What is HD Radio™ broadcasting?
HD Radio stations can deliver high-quality digital sound—AM digital will have FM-like sound quality (in stereo)
and FM digital will have CD-like sound quality—with static-free and clear reception. Furthermore, stations can
offer text and data, such as artist names and song titles.
• HD Radio tuners can also tune in to conventional analog broadcasts.
• Many HD Radio stations offer more than one channel of programming. This service is called multicasting.
• To find HD Radio stations in your area, visit <http://www.hdradio.com/>.
Listening to the radio
You can tune in to both conventional and HD Radio broadcasts.
• If you want to search for HD Radio stations only, see “Searching for HD Radio stations only” on page 9.

ENGLISH
9OPERATIONS
When receiving HD Radio
multicast channels...
Select your desired channel.
• “LINKING” appears while linking to a multicast
channel.
Searching for HD Radio stations
only
When a station is tuned in, searching stops.
Selected frequency
Lights up when a digital audio is broadcast.
Flashes when an analog audio is broadcast.
Station Call Sign
Channel number
1Select “FM” or “AM.”
2Search for a station to listen—Auto Search.
When a station is tuned in, searching stops. To stop searching, press the same button
again.
• You can also search for a station manually—Manual Search.
Hold either one of the buttons until “M” flashes on the display, then press it
repeatedly.
• When receiving an FM stereo broadcast with sufficient signal strength, the ST indicator
lights up on the display.
Ex.: When receiving a conventional FM
station
Ex.: When receiving an HD Radio station
[Hold]
Improving the FM reception
When an FM stereo broadcast is hard to receive,
activate monaural mode for better reception.
1Call up the SET menu.
2Select “TUNER.”
3Select “MONO.”
4Select “MONO ON.”
Reception improves, but stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure to select “MONO OFF.”
[Hold]
[Turn] =[Press]
[Turn] =[Press]
[Turn] =[Press]

ENGLISH
10
Storing stations in memory
You can preset up to 18 stations for FM and 6 stations
for AM.
• The HD Radio multicast channels can also be preset.
Automatic presetting —SSM (Strong-station
Sequential Memory)
1While listening to a radio...
Select “TUNER” =“SSM”
2Select the preset number range you want to
store.
3
Local stations with the strongest signals are
searched and stored automatically.
• To stop searching, press MENU.
To preset other 6 stations, repeat from step 1again.
Changing HD Radio reception
mode
While receiving an HD Radio broadcast, the unit
receives digital or analog audio automatically due to
the receiving condition.
While listening to an HD Radio station...
Select “TUNER” =“BLEND HOLD”
=“AUTO/DIGITAL/ANALOG”
• If no sound can be heard with “AUTO,” change the
setting to “ANALOG” or “DIGITAL.”
• The setting automatically returns to “AUTO” in the
following cases:
– When you tune in to another broadcast.
– When you change to another source.
– When you turn off the power.
• This setting cannot take effect for the conventional
FM/AM stations.
• If the radio station forces the reception mode to
digital, the HOLD indicator flashes.
[Turn] =[Press]
• Repeat this procedure.
[Hold]
The SET menu is called up.
Lights up when holding the digital reception.
Flashes when holding the analog reception.
• For FM: SSM 01–06 ÔSSM 07–12 Ô
SSM 13–18
• For AM: SSM 01–06
[Turn]
[Press]
[Turn] =[Press]
• Repeat this procedure.
[Hold]
The SET menu is called up.