JVC KD-R991BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH

B5A-2127-00 [M]
KD-R991BT / KD-R891BT / KD-R792BT
CD RECEIVER
INSTRUCTION MANUAL
CD
คูมือการใชงาน
JS_JVC_KD_R991BT_M_C.indd 1JS_JVC_KD_R991BT_M_C.indd 1 7/24/2017 10:05:13 AM7/24/2017 10:05:13 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2ENGLISH
CONTENTS BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
• Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
( 38) . Turn off the unit when parking at a low ceiling area.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
BEFORE USE 2
BASICS 3
GETTING STARTED 5
1 Cancel the demonstration
2 Set the clock and date
3 Set the basic settings
RADIO 7
CD/USB/iPod/ANDROID 8
Pandora® 11
Spotify 12
AUX 13
BLUETOOTH® 14
AUDIO SETTINGS 23
DISPLAY SETTINGS 28
REFERENCES 29
Maintenance
More information
TROUBLESHOOTING 32
SPECIFICATIONS 35
INSTALLATION/
CONNECTION 36
How to read this manual
• Operations are explained mainly using buttons on the faceplate of KD-R991BT and KD-R792BT .
• English indications are used for the purpose of explanation. You can select the display language from the menu. ( 6)
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
JS_JVC_KD_R991BT_M_EN_2.indd 2JS_JVC_KD_R991BT_M_EN_2.indd 2 7/24/2017 10:07:04 AM7/24/2017 10:07:04 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate
Turn on the power Press .
• Press and hold to turn off the power.
Adjust the volume Press .
• Press and hold to continuously increase the volume to 15.
Press to mute the sound or pause playback.
• Press again to cancel. The volume level returns to the previous level before muting or pause.
Select a source • Press repeatedly.
• Press , then press within 2 seconds.
Change the display information Press repeatedly.
( 31)
Select an item 1Press to select an item.
2Press to confirm.
Attach
How to reset
Detach
Faceplate for KD-R991BT / KD-R891BT
Loading slot
Display window
Detach button
Source button
Remote sensor
(Do not expose to bright sunlight.)
Reset the unit
within 5 seconds
after detaching
the faceplate.
JS_JVC_KD_R991BT_M_EN_2.indd 3JS_JVC_KD_R991BT_M_EN_2.indd 3 7/24/2017 10:07:07 AM7/24/2017 10:07:07 AM

4ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
To On the faceplate
Turn on the power Press .
• Press and hold to turn off the power.
Adjust the volume Turn the volume knob.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. The volume level returns to the previous level before muting or pause.
Select a source • Press repeatedly.
• Press , then turn the volume knob within 2seconds.
Change the display information Press repeatedly.
( 32)
Select an item 1Turn the volume knob to select an item.
2Press the knob to confirm.
Attach
How to reset
Detach
Faceplate for KD-R792BT
Volume knob
Loading slot
Detach button
Source button
Display window
Remote sensor
(Do not expose to
bright sunlight.)
Reset the unit
within 5 seconds
after detaching
the faceplate.
JS_JVC_KD_R991BT_M_EN_2.indd 4JS_JVC_KD_R991BT_M_EN_2.indd 4 7/24/2017 10:07:09 AM7/24/2017 10:07:09 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
Remote control (RM-RK52)
Aim the remote control directly at the remote sensor on the
unit.
( 3 or 4)
How to replace the battery
Pull out the insulation
sheet when using for
the first time.
To On the remote control
Adjust the
volume
Press or .
• Press and hold to continuously
increase the volume to 15.
Press to mute the sound or pause
playback.
• Press again to cancel. The volume
level returns to the previous level
before muting or pause.
Select a source Press SOURCE repeatedly.
GETTING STARTED
For key layout on the faceplate, see page3 or page4.
Cancel the demonstration
When you turn on the power for the first time (or [FACTORY RESET] is set to [YES] , 6 ),
the display shows:
KD-R991BT / KD-R891BT :
“CANCEL DEMO” “PRESS ENTER”
1 Press .
[YES] is selected for the initial setup.
2 Press again.
“DEMO OFF” appears.
KD-R792BT :
“CANCEL DEMO” “PRESS” “VOLUME KNOB”
1 Press the volume knob.
[YES] is selected for the initial setup.
2 Press the volume knob again.
“DEMO OFF” appears.
Set the clock and date
1 Press and hold .
2 Perform ‘select an item ( 3 or 4)’ operation to select [CLOCK] .
3 Perform ‘select an item ( 3 or 4)’ operation to adjust the clock.
[CLOCK ADJUST] set the hour and minute [CLOCK FORMAT] [12H] or [24H]
4 Perform ‘select an item ( 3 or 4)’ operation to set the date.
[DATE SET] set the day, month and year
5 Press to exit.
To return to the previous setting item, press .
1
2
JS_JVC_KD_R991BT_M_EN_2.indd 5JS_JVC_KD_R991BT_M_EN_2.indd 5 7/24/2017 10:07:10 AM7/24/2017 10:07:10 AM

6ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
FACTORY RESET YES :Resets the settings to default (except the stored station).;
NO :Cancels.
CLOCK
TIME SYNC ON
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Data System signal.;
OFF :Cancels.
CLOCK DISPLAY ON :The clock time is shown on the display even when the unit is
turned off.;
OFF :Cancels.
ENGLISH Select the display language for menu and music information if
applicable.
By default,
ENGLISH is selected.
ESPANOL
Set the basic settings
1 Press and hold .
2 Perform 'select an item ( 3 or 4)’ operation to select an item
(see the following table).
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
SYSTEM
KEY BEEP
(Not applicable when 3-way crossover is selected.)
ON :Activates the keypress tone.; OFF :Deactivates.
SOURCE SELECT
AM SRC
*
ON :Enables AM in source selection.; OFF :Disables. ( 7)
SW1 SRC
*
ON :Enables SW1 in source selection.; OFF :Disables. ( 7)
SW2 SRC
*
ON :Enables SW2 in source selection.; OFF :Disables. ( 7)
PANDORA SRC
*
ON :Enables PANDORA in source selection.; OFF :Disables. ( 11)
SPOTIFY SRC
*
ON :Enables SPOTIFY in source selection.; OFF :Disables. ( 12)
BUILT-IN AUX
*
ON :Enables AUX in source selection.; OFF :Disables. ( 13)
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
*
Not displayed when the corresponding source is selected.
3
JS_JVC_KD_R991BT_M_EN_2.indd 6JS_JVC_KD_R991BT_M_EN_2.indd 6 7/24/2017 10:07:13 AM7/24/2017 10:07:13 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
For key layout on the faceplate, see page3 or page4.
Search for a station
1 Press source button repeatedly to select FM, AM, SW1 or SW2.
2 Press (or press on the remote control) to search for a
station automatically.
(or)
Press and hold (or press and hold on the remote
control) until “M” flashes, then press repeatedly to search for a
station manually.
• “ST” or “STEREO” lights up when receiving an FM stereo broadcast with
sufficient signal strength.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM/SW1/SW2.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold the following button until “PRESETMODE” flashes.
KD-R991BT / KD-R891BT :
KD-R792BT : Volume knob
2 Perform ‘select an item ( 3 or 4) ’ operation to select a preset
number.
The preset number flashes and “MEMORY” appears.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press .
2 Perform ‘select an item ( 3 or 4) ’ operation to select a preset
number.
Other settings
1 Press and hold .
2 Perform 'select an item ( 3 or 4) ' operation to select an item
( see the following table ) .
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
RADIO TIMER
Turns on the radio at a specific time regardless of the current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the timer will be turned
on.
2 FM / AM / SW1 / SW2 :Select the band.
3 01 to 18 (for FM)/ 01 to 06 (for AM/SW1/SW2):Select the preset station.
4 Set the activation day
*1
and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM SRC] / [SW1 SRC] / [SW2 SRC] in
[SOURCE SELECT] after Radio Timer for AM/SW1/SW2 is selected.
( 6)
SSM SSM 01–06
/ SSM 07–12 / SSM 13–18 : Automatically presets up to 18
stations for FM. “SSM” stops flashing when the first 6 stations are stored.
Select
SSM 07–12 / SSM 13–18 to store the following 12 stations.
LOCAL SEEK ON :Searches only AM/SW1/SW2 stations with good reception.;
OFF :Cancels.
• Settings made are applicable only to the selected source/station. Once you
change the source/station, you need to make the settings again.
*1
Selectable only when [ONCE] or [WEEKLY] is selected in step 1 .
JS_JVC_KD_R991BT_M_EN_2.indd 7JS_JVC_KD_R991BT_M_EN_2.indd 7 7/24/2017 10:07:14 AM7/24/2017 10:07:14 AM

8ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
IF BAND AUTO :Increases the tuner selectivity to reduce interference
noises from adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to interference noises from adjacent FM stations, but
sound quality will not be degraded and the stereo effect will remain.
MONO SET ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
NEWS SET
*2
ON :The unit will temporarily switch to News Programme if
available.;
OFF :Cancels.
REGIONAL
*2
ON : Switches to another station only in the specific region using the
“AF” control.;
OFF :Cancels.
AF SET
*2
ON : Automatically searches for another station broadcasting the
same program in the same Radio Data System network with better
reception when the current reception is poor.;
OFF : Cancels.
TI ON : Allows the unit to temporarily switch to Traffic Information if
available (“TI” lights up) while listening to all sources except in AM/
SW1/SW2. ;
OFF :Cancels.
PTY SEARCH
*2
Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as
you have selected, that station is tuned in.
*2
Only for FM source.
PTY code
NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA , CULTURE , SCIENCE ,
VARIED , POP M (music), ROCK M (music), EASY M (music), LIGHT M
(music),
CLASSICS , OTHER M (music), WEATHER , FINANCE , CHILDREN ,
SOCIAL , RELIGION , PHONE IN , TRAVEL , LEISURE , JAZZ , COUNTRY , NATION M
(music),
OLDIES , FOLK M (music), DOCUMENT
RADIO CD/USB/iPod/ANDROID
Start playback
The source changes automatically and playback starts.
CD
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown.
Follow the instructions to install the application. You can also install the latest version of JVC
MUSIC PLAY application on your Android device before connecting. For more information, visit
<http://www.jvc.net/cs/car/>.
Eject disc Label side
KD-R991BT/KD-R891BT: KD-R792BT:
Eject disc Label side
KD-R991BT/
KD-R792BT
KD-R891BT
USB 2.0 cable
*1
(commercially available)
USB cable
*1
(commercially available)
ANDROID*2
Accessory of the iPod/iPhone
*1
iPod/iPhone
USB
USB input terminal
USB input terminal
JS_JVC_KD_R991BT_M_EN_2.indd 8JS_JVC_KD_R991BT_M_EN_2.indd 8 7/24/2017 10:07:16 AM7/24/2017 10:07:16 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
For key layout on the faceplate, see page3 or page4.
• Selectable sources:
KD-R991BT / KD-R891BT : CD/USB/iPodUSB/ANDROID
KD-R792BT : CD/USB/ANDROID
To On the faceplate On the remote control
Reverse/
Fast-forward*3
Press and hold . Press and hold .
Select a track/
file
Press .Press .
Select a folder*4Press . Press .
Repeat play*5Press repeatedly.
TRACK REPEAT / ALL REPEAT : Audio CD
TRACK REPEAT / FOLDER REPEAT / ALL REPEAT : MP3/WMA/AAC/WAV/
FLAC file
ONE REPEAT / ALL REPEAT / REPEAT OFF : iPod or ANDROID
Random play*5Press repeatedly.
ALL RANDOM / RANDOM OFF : Audio CD
FOLDER RANDOM / ALL RANDOM / RANDOM OFF : MP3/WMA/AAC/WAV/
FLAC file
SONG RANDOM / ALL RANDOM / RANDOM OFF : iPod or ANDROID
*3
For ANDROID: Applicable only when [AUTO MODE] is selected.
*4
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*5
For iPod/ANDROID: Applicable only when [HEAD MODE] / [AUTO MODE] is selected.
Select control mode
While in iPodUSB source, press repeatedly.
HEAD MODE : Control iPod from this unit.
IPHONE MODE : Control iPod using the iPod itself. However, you
can still play/pause or file skip from this unit.
While in ANDROID source, press repeatedly.
AUTO MODE : Control Android device from this unit via JVC
MUSIC PLAY application installed in the Android
device.
AUDIO MODE : Control Android device using the Android device
itself via other media player applications installed
in the Android device. However, you can still
play/pause or file skip from this unit.
Select music drive
While in USB source, press repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass
Storage Class).
• Selected drive of a multiple drives device.
JS_JVC_KD_R991BT_M_EN_2.indd 9JS_JVC_KD_R991BT_M_EN_2.indd 9 7/24/2017 10:07:17 AM7/24/2017 10:07:17 AM

10 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Settings to use JVC Remote application
(for KD-R991BT/KD-R891BT)
JVC Remote application is designed to control the JVC car receiver’s
operations from the iPhone/iPod (via USB input terminal).
Preparation:
Install the latest version of JVC Remote application on your device before
connecting. For more information, visit <http://www.jvc.net/cs/car/>.
You can make the settings in the same way as connection via Bluetooth.
( 21)
Select a file from a folder/list
For iPod/ANDROID, applicable only when [HEAD MODE] / [AUTO MODE] is
selected.
1 Press .
2 Perform ‘select an item ( 3 or 4) ’ operation to select a folder/
list.
3 Perform ‘select an item ( 3 or 4) ’ operation to select a file.
Quick search (applicable only for CD, USB and ANDROID source)
If you have many files, you can search through them quickly.
Perform the following operation to browse through the list quickly.
KD-R991BT / KD-R891BT : Press and hold
KD-R792BT : Turn the volume knob quickly
Alphabet search (applicable only for iPod USB and ANDROID source)
You can search for a file according to the first character.
For iPodUSB source
Press to select the desired character (A to Z, 0to9,
OTHERS).
• Select “OTHERS” if the first character is other than AtoZ, 0to9.
For ANDROID source
1 Press to enter character search.
2 Perform the following operation to select the desired
character.
KD-R991BT / KD-R891BT : Press
KD-R792BT : Turn the volume knob
^A^ : Upper case (A to Z)
_A_ : Lower case (a to z)
-0- : Numbers (0 to 9)
-OTHERS-: Character other than A to Z, 0 to 9
3 Press the following to start searching.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
• To return to the previous setting item, press .
• To cancel, press and hold .
JS_JVC_KD_R991BT_M_EN_2.indd 10JS_JVC_KD_R991BT_M_EN_2.indd 10 7/24/2017 10:07:18 AM7/24/2017 10:07:18 AM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora® (Applicable for Australia or New Zealand models only)
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/iPod touch), then create an account and log in to Pandora.
• Select
[ON] for [PANDORA SRC] in [SOURCE SELECT] . ( 6)
KD-R792BT
: You can only listen to Pandora via Bluetooth connection with
an Android device.
( 22)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
3 Press source button repeatedly to select PANDORA.
Broadcast starts automatically.
To On the faceplate On the remote control
Playback/pause KD-R991BT / KD-R891BT :
Press .
KD-R792BT :
Press the volume knob.
Press .
Skip a track Press T. Press I.
Thumbs up or
thumbs down*2
Press . Press .
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Create and store a new station
1 Press .
2 Perform ‘select an item ( 3 or 4) ’ operation to select [NEW
STATION]
.
3 Perform ‘select an item ( 3 or 4) ’ operation to select [FROM
TRACK]
or [FROM ARTIST] .
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (3, 4, 5or 6) to store.
To select a stored station: Press one of the number buttons (3, 4, 5or 6).
Search for a registered station
1 Press .
2 Perform ‘select an item ( 3 or 4) ’ operation to select an item.
[BY DATE] : According to the registered date
[A-Z] : By alphabetical order
3 Perform ‘select an item ( 3 or 4) ’ operation to select the
desired station.
To cancel, press and hold .
Bookmark current song information
Press and hold the following to bookmark song information.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this
unit.
USB input terminal
Accessory of the iPod/iPhone*
1
JS_JVC_KD_R991BT_M_EN_3.indd 11JS_JVC_KD_R991BT_M_EN_3.indd 11 7/24/2017 4:26:04 PM7/24/2017 4:26:04 PM

12 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Spotify
Preparation:
Install the latest version of the Spotify application on your device (iPhone/
iPod touch), then create an account and log in to Spotify.
• Select
[ON] for [SPOTIFY SRC] in [SOURCE SELECT] . ( 6)
KD-R792BT
: You can only listen to Spotify via Bluetooth connection with an
Android device.
( 22)
Start listening
1 Open the Spotify application on your device.
2 Connect your device to the USB input terminal.
3 Press source button repeatedly to select SPOTIFY.
Broadcast starts automatically
*
Do not leave the cable inside the car when not using.
To On the faceplate On the remote control
Playback/pause KD-R991BT / KD-R891BT :
Press .
KD-R792BT :
Press the volume knob.
Press .
Skip a track Press S*1 / T. Press H*1/ I.
Thumbs up or
thumbs down
*2
Press . Press .
To On the faceplate On the remote control
Start radio Press and hold 5.( Not available )
Repeat play
*3Press repeatedly.
ALL REPEAT , ONE REPEAT
*1
,
REPEAT OFF
( Not available )
Random play
*3Press repeatedly
*1.
ALL RANDOM , RANDOM OFF
( Not available )
*1
Available for premium account users only.
*2
This feature is available for tracks in Radio only. If thumbs down is selected, the current
track is skipped.
*3
Available for tracks in Playlists only.
Save favorite song information
While listening to the Radio on Spotify...
Press and hold the following button to save the song information.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
“SAVED” appears and the information is stored to “Your Music” or “Your
Library” on your Spotify account.
To unsave, repeat the same procedure.
“REMOVED” appears and the information is removed from “Your Music”
or “Your Library” on your Spotify account.
USB input terminal
Accessory of the iPod/iPhone
*
JS_JVC_KD_R991BT_M_EN_2.indd 12JS_JVC_KD_R991BT_M_EN_2.indd 12 7/24/2017 10:07:21 AM7/24/2017 10:07:21 AM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Search for a song or station
1 Press .
2 Perform ‘select an item ( 3 or 4) ’ operation to select a list type.
The list types displayed differ depending on the information sent from
Spotify.
3 Perform ‘select an item ( 3 or 4) ’ operation to select the
desired song or station.
Perform the following operation to browse through the list quickly.
KD-R991BT/KD-R891BT : Press and hold
KD-R792BT : Turn the volume knob quickly
To cancel, press and hold .
Use a portable audio player
1 Connect a portable audio player (commercially available).
KD-R991BT / KD-R891BT :
KD-R792BT :
2 Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT] . ( 6)
3 Press source button repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum
audio output.
AUX
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
Spotify
JS_JVC_KD_R991BT_M_EN_2.indd 13JS_JVC_KD_R991BT_M_EN_2.indd 13 7/24/2017 10:07:22 AM7/24/2017 10:07:22 AM

14 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the
microphone angle Secure using cord clamps
(not supplied) if necessary.
Microphone input jack
Microphone (supplied)
Rear panel
Pair and connect a Bluetooth device for the first time
1 Press source button to turn on the unit.
2 Search and select “KD-R9 BT”/“KD-R8 BT”/“KD-R7 BT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number
(PIN) code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A)
KD-R991BT / KD-R891BT : “[Device Name]” “XXXXXX” “ENTER–YES” “BACK–NO”
KD-R792BT : “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device are the same.
Press the following operation to confirm the passkey.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Operate the Bluetooth device to confirm the passkey.
(B) KD-R991BT / KD-R891BT : “[Device Name]” “ENTER–YES” “BACK–NO”
KD-R792BT : “[Device Name]” “VOL–YES” “BACK–NO”
Press the following to start pairing.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing.
( 19)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the
Bluetooth connection is established.
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if
you reset the unit. To delete the paired device,
19 , [DEVICE DELETE] .
JS_JVC_KD_R991BT_M_EN_2.indd 14JS_JVC_KD_R991BT_M_EN_2.indd 14 7/24/2017 10:17:06 AM7/24/2017 10:17:06 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
• A maximum of two Bluetooth phones and one
Bluetooth audio device can be connected at any
time.
However, while in BT AUDIO source, you can
connect to five Bluetooth audio devices and
switch between these five devices. (
20 )
• Some Bluetooth devices may not automatically
connect to the unit after pairing. Connect the
device to the unit manually.
• Refer to the instruction manual of the Bluetooth
device for more information.
Auto Pairing
When you connect the following devices to the USB
input terminal, pairing request (via Bluetooth) is
automatically activated.
KD-R991BT / KD-R891BT : iPhone/iPod touch/Android
device
KD-R792BT : Android device
Press the following to pair once you have
confirmed the device name.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Automatic pairing request is activated only if:
– Bluetooth function of the connected devcie is
turned on.
–
[AUTO PAIRING] is set to [ON] . ( 19)
– JVC MUSIC PLAY application is installed on
the Android device
( 8) and [AUTO MODE] is
selected
( 9) .
BLUETOOTH — Mobile phone
For key layout on the faceplate, see page3 or page4.
Receive a call
When there is an incoming call:
•
KD-R991BT/KD-R891BT :
The symbolic button will blink in the color you have selected in
[RING COLOR] . ( 17)
KD-R792BT :
The buttons will blink in the blinking pattern you have selected in
[RING ILLUMI] . ( 17)
• The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 17)
During a call:
•
KD-R991BT/KD-R891BT :
The symbolic button stop blinking and illuminate in the color you have selected in
[RING
COLOR]
. ( 17)
KD-R792BT : The buttons stop blinking.
• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
The following operations may differ or not available depending on the connected phone.
To On the faceplate On the remote control
First incoming call...
Answer a call Press or the following button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Press .
Reject a call Press and hold or the
following button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Press and hold .
End a call Press and hold or the
following button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Press and hold .
JS_JVC_KD_R991BT_M_EN_2.indd 15JS_JVC_KD_R991BT_M_EN_2.indd 15 7/24/2017 10:07:26 AM7/24/2017 10:07:26 AM

16 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
To On the faceplate On the remote control
While talking on the first incoming call...
Answer another incoming
call and hold the current call
Press or the following button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
( Not available )
Reject another incoming call Press and hold or the following
button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
( Not available )
While having two active calls...
End current call and activate
held call
Press and hold or the following
button.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
Press and hold
.
Swap between the current
call and held call
Press .( Not available )
Adjust the phone volume*1
[00] to [35] (Default: [15] )
Perform the following operation
during a call.
KD-R991BT / KD-R891BT : Press *2
KD-R792BT : Turn the volume knob
Press
*2or
during a call.
Switch between hands-free
and private talk modes*3
Press during a call. ( Not available )
*1
This adjustment will not affect the volume of the other sources.
*2
Press and hold to continuously increase the volume to 15.
*3
Operations may vary according to the connected Bluetooth device.
Improve the voice quality
While talking on the phone....
1 Press and hold .
2 Perform ‘select an item ( 3 or 4) ’
operation to select an item
( see the
following table
) .
3 Repeat step 2until the desired item is
selected or activated.
4 Press to exit.
To return to the previous setting item, press
.
Default:
XX
MIC GAIN LEVEL –10 to LEVEL +10 ( LEVEL –04 ):
The sensitivity of the microphone
increases as the number increased.
NR LEVEL LEVEL –05 to LEVEL +05 ( LEVEL 00 ):
Adjust the noise reduction level until the
least noise is being heard during a phone
conversation.
ECHO CANCEL LEVEL –05 to LEVEL +05 ( LEVEL 00 ):
Adjust the echo cancellation delay time
until the least echo is being heard during
a phone conversation.
JS_JVC_KD_R991BT_M_EN_2.indd 16JS_JVC_KD_R991BT_M_EN_2.indd 16 7/24/2017 10:07:28 AM7/24/2017 10:07:28 AM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Perform ‘select an item ( 3 or 4) ’ operation to select
an item
( see the following table ) .
3 Repeat step 2until the desired item is selected or activated.
To return to the previous setting item, press .
Default:
XX
SETTINGS
AUTO ANSWER 01 SEC
to 30 SEC :The unit answers incoming call
automatically in the selected time (in seconds).;
OFF :Cancels.
RING COLOR KD-R991BT / KD-R891BT :
COLOR 01 to COLOR 49 ( COLOR 08 ): Selects the illumination
color for the symbolic button as notification when there is an
incoming call and during a call.;
OFF :Cancels.
RING ILLUMI KD-R792BT :
BLINK 01 to BLINK 05 ( BLINK 02 ): Selects the blinking
pattern for the buttons as notification when there is an
incoming call.;
OFF :Cancels.
BATT/SIGNAL
*
KD-R991BT / KD-R891BT :
AUTO :Shows the strength of the battery and signal when the
unit detects a Bluetooth device and the Bluetooth device is
connected.;
OFF :Cancels.
*
Functionality depends on the type of the phone used.
BLUETOOTH®
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call
by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
“(First device name)” appears.
• If two Bluetooth phones are connected, press again to switch to
another phone.
“(Second device name)” appears.
2 Perform ‘select an item ( 3 or 4) ’ operation to select an item ( see the
following table
) .
3 Repeat step 2until the desired item is selected/activated or follow the
instructions stated on the selected item.
To return to the previous setting item, press .
RECENT CALL (Applicable only if the phone supports PBAP.)
1 Press the following button to select a name or a phone number.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
• “<” indicates call received, “>“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the following to call.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
PHONEBOOK (Applicable only if the phone supports PBAP.)
1 Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2 Perform ‘select an item ( 3 or 4) ’ operation to select a name.
3 Perform ‘select an item ( 3 or 4) ’ operation to select a phone number
and to call.
• The phonebook of the connected phone is automatically transferred to the unit
when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns
as “U”.)
JS_JVC_KD_R991BT_M_EN_2.indd 17JS_JVC_KD_R991BT_M_EN_2.indd 17 7/24/2017 10:07:30 AM7/24/2017 10:07:30 AM

18 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
DIAL NUMBER 1 Perform the following operation to select a number (0 to 9) or character
(, #, +).
KD-R991BT / KD-R891BT : Press
KD-R792BT : Turn the volume knob
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press the following to call.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
VOICE Speak the name of the contact you want to call or the voice command to
control the phone functions.
( Make a call using voice recognition)
Make a call using voice recognition
1 Press and hold to activate the connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of
iPhone.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1to 6).
1 Press to enter Bluetooth mode.
2 Perform ‘select an item ( 3 or 4) ’ operation to select
[RECENT CALL] , [PHONEBOOK] or [DIAL NUMBER] .
3 Perform ‘select an item ( 3 or 4) ’ operation to select a
contact or enter a phone number.
If a contact is selected, press the following to show the phone
number.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
4 Press and hold one of the number buttons (1to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select
[DIAL NUMBER] in step 2
and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press the following to call.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
“NO PRESET” appears if there is no contact stored.
JS_JVC_KD_R991BT_M_EN_2.indd 18JS_JVC_KD_R991BT_M_EN_2.indd 18 7/24/2017 10:07:31 AM7/24/2017 10:07:31 AM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Bluetooth mode settings
1 Press and hold .
2 Perform ‘select an item ( 3 or 4) ’ operation to select an item
( see the following table ) .
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
BT MODE
PHONE SELECT
* Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name when connected.
“” appears in front of the current playback audio device.
AUDIO SELECT *
DEVICE DELETE 1 Perform ‘select an item ( 3 or 4) ’ operation to select a
device to delete.
2 Perform ‘select an item ( 3 or 4) ’ operation to select [YES]
or
[NO] .
PIN CODE EDIT
(0000)
Changes the PIN code (up to 6 digits).
1 Perform the following operation to select a number.
KD-R991BT / KD-R891BT : Press
KD-R792BT : Turn the volume knob
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the PIN code.
3 Press the following to confirm.
KD-R991BT / KD-R891BT :
KD-R792BT : volume knob
* You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device
at any time.
RECONNECT ON :The unit automatically reconnect when the last connected
Bluetooth device is within range.;
OFF :Cancels.
AUTO PAIRING ON :The unit automatically pair supported Bluetooth device (iPhone/
iPod touch/Android device) when it is connected through USB input
terminal.Depending on the operating system of the connected device,
this function may not work. ;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.).;
NO :Cancels.
INFORMATION MY  BT  NAME : Displays the unit name (“KD-R9 BT”/
“KD-R8 BT”/“KD-R7 BT”).;
MY  ADDRESS : Shows address of this unit.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING
PHONE” “PIN IS 0000” scrolls on the display.
2 Search and select “KD-R9 BT”/“KD-R8 BT”/“KD-R7 BT” on the
Bluetooth device within 3minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
JS_JVC_KD_R991BT_M_EN_2.indd 19JS_JVC_KD_R991BT_M_EN_2.indd 19 7/24/2017 10:07:33 AM7/24/2017 10:07:33 AM

20 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
After pairing is successful, “PAIRING OK”
“[Device Name]” appears and Bluetooth
compatibility check starts.
If “CONNECT NOW USING PHONE” appears,
operate the Bluetooth device to allow
phonebook access to continue.
“TESTING” flashes on the display.
The connectivity result flashes on the
display.
“PAIRING OK” and/or “HANDS-FREE OK”*1
and/or “AUD.STREAM OK”*2and/or “PBAP
OK”*3: Compatible
*1
Compatible with Hands-Free Profile (HFP)
*2
Compatible with Advanced Audio Distribution Profile
(A2DP)
*3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED”
appears to indicate that pairing has been
deleted, and the unit exits check mode.
• To cancel, press and hold source button
to turn off the power, then turn on the
power again.
BLUETOOTH — Audio
For key layout on the faceplate, see page3 or page4.
While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these
five devices.
Audio player via Bluetooth
1 Press source button repeatedly to select BTAUDIO (or press SOURCE on the remote control).
• Pressing enters BT AUDIO directly.
2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback/pause
KD-R991BT / KD-R891BT : Press .
KD-R792BT : Press the volume knob. Press .
Select group or folder Press . Press .
Reverse skip/Forward skip Press .Press .
Reverse/Fast-forward Press and hold .Press and hold .
Repeat play Press repeatedly.
TRACK REPEAT , ALL REPEAT , REPEAT OFF
( Not available )
Random play Press repeatedly.
GROUP RANDOM , ALL RANDOM , RANDOM OFF
( Not available )
Select a file from a folder/
list
Refer to “Select a file from a folder/list” on
page10. ( Not available )
Switch between connected
Bluetooth audio devices
Press 5.*( Not available )
*
Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.
Operations and display indications may differ according to their availability on the connected device.
JS_JVC_KD_R991BT_M_EN_2.indd 20JS_JVC_KD_R991BT_M_EN_2.indd 20 7/24/2017 10:07:35 AM7/24/2017 10:07:35 AM