JVC UX-V10E User manual

MICRO COMPONENT SYSTEM
SISTEMAS DE MICROCOMPONENTES
UX-V10
UX-V10GN
UX-V10WT
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0031-003A
[U/US/UT/UX/UY/UB]
MANUEL DE INSTRUCCIONES
AUTO REVERSE
AUTOTAPE SELECTOR
DOWN UPMULTICONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV.
MODE
AHB
PRO
TIMER
CLOCK
VERTICAL DISC
LOADING MECHANISM
COMPACT
DIGITAL AUDIO
VOLUME
CD
OPEN/CLOSE
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
TAPE
MICRO COMPONENT SYSTEM UX-V10
COVER.UX-V10[U] 00.4.19, 10:29 AM3

Caution –– switch!
Disconnect the mains plug to shut the power off
completely. The switch in any position does not
disconnect the mains line. The power can be remote
controlled.
Precaución –– Interruptor !
Desconectar el cable de alimentación para desactivar
la alimentación totalmente. Cualquier que sea la
posición de ajuste del interruptor , la alimentación
no es cortada completamente. La alimentación puede
ser controlada remotamente.
Warnings, Cautions and Others
Avisos, precauciones y otras notas
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
PRECAUCIÓN
Para reducir riesgos de choques eléctricos, incendio,
etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2. No exponga este aparato a la lluvia o a la
humedad.
G-1
G1-G3.UX-V10[U].6.0 00.4.19, 10:36 AM2

UX-V10/UX-V10GN/UX-V10WT
TAPE FM/AM CD
VERTICALDISC
LOADINGMECHANISM
COMPACT
DIGITALAUDIO
MICROCOMPONENT SYSTEM UX-V10
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10
cm or more.
Precaucion: ventilación correcta
Para evitar el riesgo de descargas eléctricas e incendio y prevenir posibles daños, instale el equipo en un lugar
que cumpla los siguientes requisitos:
1 Parte frontal:
Sin obstrucciones, espacio abierto.
2 Lados/parte superior/parte posterior:
No debe haber ninguna obstrucción en las áreas mostradas por las dimensiones de la siguiente figura.
3 Parte inferior:
Sitúe el equipo sobre una superficie nivelada. Mantenga un espacio adecuado para permitir el paso del aire y
una correcta ventilación, situando el equipo sobre un soporte de 10 o más cm de allura.
15 cm 1 cm
15 cm
15 cm
15 cm 15 cm 1 cm
10 cm
UX-V10
UX-V10GN
UX-V10WT
G-2
G1-G3.UX-V10[U].6.0 00.4.19, 10:36 AM3

IMPORTANT FOR LASER PRODUCTS / IMPORTANTE PARA PRODUCTOS LÁSER
/
REPRODUCTION OF LABELS / REPRODUCCIÓN DE ETIQUETAS /
1 CLASSIFICATION LABEL, PLACED ON REAR ENCLO-
SURE
1 ETIQUETA DE CLASIFICACIÓN, PEGADA EN LA PARTE
POSTERIOR DE LA CAJA
2 WARNING LABEL, PLACED INSIDE THE UNIT
2 ETIQUETA DE ADVERTENCIA, PEGADA EN EL INTE-
RIOR DE LA UNIDAD
CLASS 1
LASER PRODUCT
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to quali-
fied service personnel.
1. PRODUCTO LÁSER CLASE 1
2. PELIGRO:Enelinteriorhayradiaciónláserinvisible.Eviteel
contacto directo con el haz.
3. PRECAUCIÓN: No abra la tapa superior. En el interior de la
unidadnoexistenpiezasreparablesporelusuario;dejetodo
servicio técnico en manos de personal calificado.
DANGER: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsæt-
telse for stråling (d)
VARNING: Osynlig laser-
strålning när denna del är
öppnad och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja suo-
jalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
G-3
/
/
G1-G3.UX-V10[U].6.0 00.4.19, 10:36 AM4

1
English
Thank you for purchasing the JVC Micro Component System.
We hope it will be a valued addition to your home, giving you years of enjoyment.
Be sure to read this instruction manual carefully before operating your new stereo system.
In it you will find all the information you need to set up and use the system.
If you have any query that is not answered by the manual, please contact your dealer.
Features
Here are some of the things that make your System both powerful and simple to use.
■The controls and operations have been designed to make them very easy to use, freeing you to just enjoy the music.
• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette deck or CD
Player with a single touch.
■The System incorporates Active Hyper Bass PRO circuitry to faithfully reproduce low frequency sounds.
■Forty-five-station preset capability (30 FM and 15 AM) in addition to auto-seek and manual tuning.
■Versatile CD options include repeat, random and program play.
■Timer functions; Daily Timer, Recording Timer and Sleep Timer.
■Auto-reverse tape function.
■You can connect various external equipment.
• For Hong Kong, the external equipment is used as playback and recording device.
• For the other areas, it is used only as a playback device.
How This Manual Is Organized
• Basic information that is the same for many different functions – e.g. setting the volume – is given in the section “Common
Operations,” and not repeated under each function.
• The names of buttons/controls and display messages are written in all capital letters: e.g. TAPE, “NO DISC.”
IMPORTANT PRECAUTIONS
1 Installation of the System
• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C.)
• Leave sufficient distance between the System and a TV.
• Do not use the System in a place subject to vibrations.
2 Power cord
• Do not handle the power cord with wet hands!
• Some power is always consumed as long as the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
3 Malfunctions, etc.
• There are no user serviceable parts inside. In case of a system failure, unplug the power cord and consult your dealer.
• Do not insert any metallic object into the System.
Table of Contents
Features..................................................................................1
How This Manual Is Organized.............................................1
IMPORTANT PRECAUTIONS ............................................1
Getting Started ...........................................................2
Common Operations..................................................6
Using the Tuner ..........................................................8
Using the CD Player .................................................10
Using the Cassette Deck (Listening to a Tape) ..... 13
Using the Cassette Deck (Recording) ................... 14
Using External Equipment.......................................16
Using the Timers ......................................................17
Care and Maintenance .............................................20
Troubleshooting .......................................................21
Specifications ...........................................................22
EN01-09.UX-V10[U] 00.4.19, 10:45 AM1

2
English
Getting Started
Accessories
Make sure that you have all of the following items, which are supplied with the System.
AC Power Cord (1)
AM Loop Antenna (1)
Remote Control (1)
Batteries (2)
FM Wire Antenna (1)
AC Plug Adaptor (except for Hong Kong and Argentina) (1)
If any of these items are missing, contact your dealer immediately.
Setting the VOLTAGE SELECTOR Switch
To avoid damaging the System, set the voltage before plugging in the system.
Set the correct voltage for your area with the VOLTAGE SELECTOR switch on the back of the Unit. Use a screwdriver to rotate the selector
so that the voltage number the arrow is pointed at is the same as the voltage in your area.
How to Put Batteries in the Remote Control
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.
CAUTION: Handle batteries properly.
To avoid battery leakage or explosion:
• Remove batteries when the Remote Control will not be used for a long time.
• When you need to replace the batteries, replace both batteries at the same time with new ones.
• Do not use an old battery with a new one.
• Do not use different types of batteries together.
Using the Remote Control
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7 m away.
You need to point the Remote Control at the remote sensor on the System’s front panel.
VOLTAGE SELECTOR
110V
127V
230V
AUTOREVERSE
AUTOTAPESELECTOR
TAPE
DOWN UPMULTICONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV.
MODE
AHB
PRO
TIMER
CLOCK
VERTICAL DISC
LOADING MECHANISM
COMPACT
DIGITALAUDIO
VOLUME
CD
OPEN/CLOSE
MICRO COMPONENT SYSTEM UX-V10
Remote sensor
R6(SUM-3)/AA(15F)
EN01-09.UX-V10[U] 00.4.19, 10:45 AM2

3
English
CAUTION: Make all connections before plugging the System into an AC power outlet.
Connecting the FM Antenna
Turn the loop until you have the best reception.
CAUTION:
To avoid noise, keep antennas away from the
System, the connecting cord and the AC power
cord.
Connecting the AM Antenna
AM Loop Antenna (supplied)
Attach the AM loop to its base by snapping the tabs on the loop
into the slot in the base.
Using the supplied Wire Antenna
Using the coaxial type connector
(not supplied)
A 75 Ωantenna with coaxial type connector (IEC or DIN 45325)
should be connected to the FM (75 Ω) COAXIAL terminal.
If reception is poor, connect the outdoor antenna.
Note: Before attaching a 75 Ωcoaxial lead (the kind with a
round wire going to an outdoor antenna), disconnect the
supplied FM Wire Antenna.
FM Wire Antenna
(supplied)
Coaxial cable
FM outdoor antenna
(not supplied)
AM EXT
AM LOOP
FM (75Ω)
COAXIAL
ANTENNA
OPTICAL
DIGITAL OUT
RL
R
L
SPEAKERS
IMPEDANCE
MIN 4Ω
AC IN
VOLTAGE SELECTOR
110V
127V
230V
Rear Panel of the Unit
Rear Panel of the Unit
For
Hong Kong
only
For
Hong Kong
only
OPTICAL
DIGITAL OUT
RL
R
L
SPEAKERS
IMPEDANCE
MIN 4Ω
AC IN
VOLTAGE SELECTOR
110V
127V
230V
EN01-09.UX-V10[U] 00.4.19, 10:45 AM3

4
English
CAUTION: Make all connections before plugging the System into an AC power outlet.
Connecting the Speakers
For each speaker, connect one end of the speaker wire to the speaker terminals on the back of the System.
1. Open each of the terminals and insert the speaker wires firmly, then close the terminals.
2. Connect the red (+) and black (–) wires of the right side speaker to the red (+) and black (–) terminals marked R on the System.
Connect the red (+) and black (–) wires of the left side speaker to the red (+) and black (–) terminals marked L on the System.
CAUTION:
If a TV is installed near the speakers, the picture on the TV may be distorted. If this happens, set the
speakers away from the TV.
Connecting External Equipment
For Hong Kong:
Connect signal cords (not supplied) between the System’s LINE IN (AUX)/LINE OUT terminals and the output/input terminals of an
external MD recorder, cassette deck, etc.
You can then listen to the external source through the System, or record the System’s CD player, cassette tape, or tuner to the external unit.
For the other areas:
You can connect an audio equipment — used only as a playback device.
Connect the audio output terminals on the other equipment and the LINE IN (AUX) terminals on the rear, using a signal cord (not supplied).
Connecting an MD Recorder, etc. (Digital Output)
(For Hong Kong only)
Unplug the cap and connect an optical digital cord (not supplied) between the System’s OPTICAL DIGITAL OUT terminal and the input
terminal of an MD recorder, etc.
You can record the digital output signal from the System’s CD Player to the MD recorder, etc.
L
R
SPEAKERS
IMPEDANCE
MIN 4Ω
Right speaker (rear side) Left speaker (rear side)
Black
LINE OUT
LINE IN
(AUX)
RL
Signal cord (not supplied)
Pin-plug x 2
Signal cord (not supplied)
Pin-plug x 2
Pin-plug x 2Pin-plug x 2
To audio output
MD recorder or cassette
deck (not supplied)
To audio input
For Hong Kong only
OPTICAL
DIGITAL OUT
MD recorder, etc. (not supplied)
Optical digital cord (not supplied)
To optical digital
input
Cap
EN01-09.UX-V10[U] 00.4.19, 10:45 AM4

5
English
Connecting the AC Power Cord
Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit.
CAUTIONS:
• ONLY USE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNCTION OR DAMAGE
TO THE SYSTEM.
• BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN YOU ARE GOING OUT OR WHEN
THE SYSTEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.
Now you can plug the AC power cord into the wall outlet, and your System is at your command!
COMPU PLAY
The JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch.
With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment at a single press of the play button
for that function. One Touch Operation turns the power on for you, then starts the function you have specified.
How One Touch Operation works in each case is explained in the section dealing with that function.
The COMPU PLAY buttons are:
AUTOMATIC POWER ON
The System automatically turns on with the following operation.
• When you press the CD OPEN/CLOSE 0button on the Unit (or CD 0button on the Remote Control), the System automatically turns
on and the CD cover opens to allow CD insertion. However, this operation does not change the source to CD.
When you press the button to turn on or off the System, the CD cover will automatically close if it is open.
On the Unit
CD #/8button
FM/AM button
TAPE @#button
AUX button
On the Remote Control
CD #/8button
FM/AM button
TAPE @#button
AUX button
AC IN
AC power cord
EN01-09.UX-V10[U] 00.4.19, 10:45 AM5

6
English
Common Operations
Adjusting the Volume
Press the VOLUME + button to increase the volume or press the
VOLUME – button to decrease it.
You can adjust the volume level between 0 and 40.
CAUTION:
DO NOT turn off (on standby) the Unit with the
volume set to an extremely high level; otherwise
a sudden blast of sound could damage your
hearing, speakers and/or headphones when you
turn on the Unit or start playing any source next
time.
REMEMBER you cannot adjust the volume level
while the Unit is on standby.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers.
Be sure to turn down the volume before connecting or putting on
headphones.
SLEEP
Turning the Power On and Off
Turning the System on –––––––––––––––
Press the button.
The STANDBY lamp goes out.
The System comes on ready to play the source it was for when the
power was last turned off.
■For example, if the last thing you were doing was listening to a
CD, you are now ready to listen to a CD again. If you wish,
you can change to another source.
■If you were listening to the Tuner last, the Tuner comes on
playing the station it was last set to.
Turning the System off –––––––––––––––
Press the button again.
The STANDBY lamp lights up.
■Some power is always consumed even though power is turned
off (called Standby Mode).
■To switch off the System completely, unplug the AC power
cord from the wall outlet. When you unplug theAC power
cord, the clock will be reset to 0:00.
DOWN UPMULTI CONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
VOLUME +, –
AHB PRO
CLOCK
PHONES
TREBLE
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
VOLUME +, –
STANDBY lamp
BASS
AHB PRO
UP
DOWN
DISPLAY
EN01-09.UX-V10[U] 00.4.19, 10:45 AM6

7
English
Showing the Clock Time
In Standby mode, the digital clock appears on the display.
When the System is turned on, you can display the digital clock
any time.
To display the digital clock, press the CLOCK button on the
Unit or DISPLAY button on the Remote Control.
To return to the previous mode, press the same button again.
Note: To let the clock work, you need to set the clock beforehand.
(See “Setting the Clock” on page 17.)
Reinforcing the Bass Sound
(AHB PRO)
You can reinforce the bass sound to maintain rich, full bass at low
volume (you can use this effect only for playback):
To get the effect, press the AHB (Active Hyper Bass) PRO
button.
The BASS indicator lights up on the display.
To cancel the effect, press the button again.
The BASS indicator goes out.
Controlling the Tone (Bass/
Treble)
You can control the tone by changing the bass and treble.
Adjusting the bass level –––––––––––––
You can adjust the bass level (low frequency range level) between
–5 and +5. (0: Flat)
1 Press the BASS button on the Remote
Control.
2 Press the UP or DOWN button on the
Remote Control to adjust the bass level.
Adjusting the treble level ––––––––––––
You can adjust the treble level (high frequency range level)
between –5 and +5. (0: Flat)
1 Press the TREBLE button on the Remote
Control.
2 Press the UP or DOWN button on the
Remote Control to adjust the treble level.
DOWN UPBASS
TREBLE DOWN UP
or
or
EN01-09.UX-V10[U] 00.4.19, 10:45 AM7

8
English
Using the Tuner
FM mode indicators
Tuning In a Station
1 Press the FM/AM button.
The band and frequency you were last tuned to appear on the
display.
(If the last station was selected using the preset number, the
preset number appears first.)
Each time you press the button, the band alternates between
FM and AM.
2 Select a station using one of the
following methods.
■Manual Tuning
Press the 4or ¢button repeatedly to move from
frequency to frequency until you find the station you want.
OR
■Auto Tuning
If you press and hold the 4or ¢button for one second or
more, the frequency changes down, or up, automatically until a
station is found. OR
■Preset Tuning using the Remote Control (Possible
only after presetting stations)
Select the desired preset number using the UP, DOWN, > or <
button on the Remote Control.After 1 second the display will
show the preset number’s band and frequency.
Example: Press the UP button until the preset number 12
“P-12” appears.
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
Band display, Frequency
display, Preset channel
FM/AM
¢
4
You can listen to FM and AM stations. Stations can be tuned in
manually, automatically, or from preset memory storage.
■Before listening to the radio:
• Make sure that both the FM andAM antennas are correctly
connected. (See page 3.)
Setting the AM tuner interval
spacing –––––––––––––––––––––––––––––––
When shipped, the AM tuner interval is set to 9 kHz or 10 kHz
spacing (Initial setting: U/UB/US/UT/UX...9 kHz, UY...10 kHz).
You can change it to 10 kHz or 9 kHz spacing.
To select 10 kHz intervals, while holding down the ¢button
on the Unit in Standby mode, press the button on the Unit to
turn on the power (at the same time, the 100 kHz spacing is
selected for FM broadcast).
To select 9 kHz intervals again, while holding down the 4
button on the Unit in Standby mode, press the button on the
Unit to turn on the power.
Note: When you change the setting, the preset stations are erased.
You will need to preset the stations again. (See page 9.)
One touch radio ––––––––––––––––––––––
Just press the FM/AM button to turn on the System and start
playing the station you were last tuned to.
■You can switch from any other sound source to the radio by
pressing the FM/AM button.
MONO STEREO
FM/AM
AM
FM
[10 kHz Intervals] [9 kHz Intervals]
DOWN
UP
++
UB... Hong Kong UX... SaudiArabia
US... Singapore UY... Argentina
UT... Taiwan ROC U... Others
AM
FM
FM/AM
(On the Unit) (On the Remote Control)
DOWNUP
(After 1 second)
or
DOWN UPMULTICONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
AUTO PRESET
FM/AM
FM MODE
¢
4
DOWN
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
UP
<>
SET
EN01-09.UX-V10[U] 00.4.19, 10:45 AM8

9
English
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM stations
using the Remote Control.
Note: Preset numbers may have been set to factory test frequen-
cies prior to shipment. This is not a malfunction.You can
preset the stations you want into memory by following one
of the presetting methods below.
Presetting stations manually ––––––––
1 Select a band by pressing the FM/AM
button.
2 Press the 4or ¢button to tune in a
station.
3 Press the SET button.
“SET” will flash for 5 seconds.
Within 5 seconds, proceed to the next step.
When the display returns to the one set in Step 2 after 5
seconds, press the SET button again.
4 Press the UP, DOWN, > or < button within
5 seconds to select the preset number.
UP or > button: Increases the preset number by 1.
DOWN or < button: Decreases the preset number by 1.
• When the > or < button is held down, the preset number
changes rapidly.
5 Press the SET button within 5 seconds.
“STORED” appears and after 2 seconds, the display returns to
the broadcast frequency display.
6 Repeat above steps 1 to 5 for each
station you want to store in memory with
a preset number.
To change the preset stations, repeat the same steps as above.
Presetting stations automatically –––
In each band, you can automatically preset 30 FM and 15 AM
stations. Preset numbers will be allocated as stations are found,
starting from the lowest frequency and moving up the frequency.
1 Select a band by pressing the FM/AM
button.
2 Press the AUTO PRESET button on the
Remote Control for more than 2 seconds.
3 Repeat steps 1 – 2 for the other band.
■If you want to change the preset stations, carry out the Manual
Presetting for the desired preset numbers.
CAUTION:
Even if the system is unplugged or if a power
failure occurs, the preset stations will be stored
for about 24 hours. However, in case the preset
stations are erased, you will need to preset the
stations again.
Changing the FM Reception
Mode
When you have tuned into an FM stereo broadcast, the STEREO
indicator lights up and you can hear stereo effects.
If an FM stereo broadcast is hard to receive or noisy, you can select
Monaural mode. Reception improves, but you lose any stereo
effect.
Press the FM MODE button on the Remote
Control so that the MONO indicator lights up
on the display.
To restore the stereo effect, press the FM MODE button on
the Remote Control so that the MONO indicator goes off.
MONO
STEREO
FM
MODE
(Within 5 seconds)
or
SET
FM = 30, AM = 15
STORED
FM/AM SET SET
DOWN
UP
When changing the Band
AUTO
PRESET
FM/AM
(For more than 2 seconds)
EN01-09.UX-V10[U] 00.4.19, 10:45 AM9

10
English
Using the CD Player
CD #¥8
UP
7
<
PROGRAM
4
CD 0
REPEAT
RANDOM
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
You can use Normal, Random, Program or Repeat Play. Repeat
Play can repeat all the tracks or just one of the tracks on the CD.
Here are the basic things you need to know to play a CD and locate
the different tracks on it.
The quickest way to start a CD is with the one touch
operation
■Press the CD #/8button on the Unit or the Remote Control.
• The power is automatically turned on. If a CD is already
inserted, it will start playing from the first track.
• If no CD is inserted, “NO DISC” appears on the display and
the CD Player remains in Stop mode.
Inserting a CD
1 Press the CD OPEN/CLOSE 0button on
the Unit (or the CD 0button on the
Remote Control.)
The CD cover opens.
2 Place a CD, with its label side out as
shown below. Press down on the portions
around the CD’s center hole until you
hear a click.
3 Press the CD OPEN/CLOSE 0button on
the Unit (or the CD 0button on the
Remote Control) again to close the CD
cover.
• To close the CD cover and play the CD, you can just press the
CD #/8button.
■You can place an 8 cm CD without an adaptor.
■When a CD with 16 tracks or more is loaded, the OVER
indicator will light up on the display.
■If the CD cannot be read correctly (because it is scratched, for
example), “00 0000” appears on the display.
■You can insert a CD while listening to another source.
CAUTIONS:
• DO NOT try to open or close the CD cover by
hand as it will be damaged.
• When you place or take out a CD, do not let it
fall. Be careful not to scratch your fingers
with the CD cover.
Unloading a CD
Take out the CD as shown below.
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
PROGRAM RANDOMPROGRAM RANDOM OVER
OVER
ALL
ALL
1234567891010 11 1212 1313 1414 1515
OVER indicator
Music calendar
Play mode indicator Repeat indicator
Track numberexceeding
15 is not displayed.
Track number, Playing time,
Program order number
¢
DOWN
CANCEL
>
SET
CD Cover
4
7
¢
CD #/8
CD OPEN/
CLOSE 0
DOWN UPMULTI CONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
VERTICAL DISC
LOADING MECHANISM
COMPACT
DIGITAL AUDIO
MICRO COMPONENT SYSTEM UX-V10
EN10-22.UX-V10[U] 00.4.19, 10:48 AM10

11
English
4 Press the PROGRAM button.
The System enters the programing mode and the PROGRAM
indicator lights up.
5 Press the > or < button to select the track
to program.
> button: Increases the track number by 1.
< button: Decreases the track number by 1.
• When the > or < button is held down, the track number
changes rapidly.
6 Press the SET button.
7 Repeat steps 5 and 6 to select the other
tracks for the program.
You can see the total playback time of programed tracks on the
display.You can also see the programed tracks on the music
calendar.
8 Press the CD #/8button.
The System plays the tracks in the order you have programed
them.
■You can skip to a particular program track by pressing the 4
or ¢button (or the <, >, DOWN or UP button on the Remote
Control) during Program Play.
■To stop playing, press the 7button once.
To confirm the programed tracks while the CD player is
stopped, press the PROGRAM button; the tracks making up the
program will successively be displayed in the programed order.
To delete all the tracks in the program while the CD
player is stopped, press the 7button. Pressing the CD 0button
on the Remote Control (or the CD OPEN/CLOSE 0button on the
Unit) to open the CD cover will also clear the programed tracks.
To exit from the program mode while the CD player is
stopped, press the 7button to light off the PROGRAM indicator.
All the programed tracks will be cleared.
Notes:
• If the total playback time of the programed tracks exceeds 99
minutes 59 seconds, “-- -- : -- --” appears on the display.
• If you try to program the 21st track, “FULL” appears on the
display for about 2 seconds.
Modifying the program –––––––––––––––
Modify the contents of the program while the CD Player is stopped.
Each time you press the CANCEL button, the last track in the
program is deleted. To add new tracks to the end of the program,
repeat above steps 5 to 7.
PROGRAM
PROGRAM RANDOM
Total playback time of the
programed tracks
Program order number
Track number Playback time
Total track number
Basics of Using the CD
Player — Normal Play
Playing a CD––––––––––––––––––––––––––
1 Insert a CD.
2 Press the CD #/8button.
The first track of the CD begins playing.
• The track number that has already played disappears from the
music calendar.
• The CD Player automatically stops when the last track of the
CD has finished playing.
To stop playing the CD, press the 7button.
The following information for the CD is displayed.
To stop playing and remove the CD, press the CD OPEN/
CLOSE 0button on the Unit or CD 0button on the Remote
Control to open the CD cover. Then remove the CD.
To pause, press the CD #/8button. The playback time flashes on
the display.
To cancel pause, press the same button again. Play continues
from the point where it was paused.
Selecting a track–––––––––––––––––––––
During playback, press the 4or ¢button (or the <, >, DOWN
or UP button on the Remote Control) to select the track you want.
The selected track starts playing.
• Press the ¢button (or the > or UP button on the Remote
Control) once to skip to the beginning of the next track.
• Press the 4button (or the < or DOWN button on the
Remote Control) to skip to the beginning of the track being
played. Press twice quickly to skip to the beginning of the
previous track.
• When the > or < button on the Remote Control is held
down, the tracks are successively skipped.
Selecting a passage within a track ––––
Holding down the 4or ¢button (or the DOWN or UP button
on the Remote Control), during playback, will fast-forward/reverse
the CD so you can quickly find a particular passage in the track
you are listening to.
Programing the Playing
Order of the Tracks
You can program the playing order of the tracks using the
Remote Control.
■You can program up to 20 tracks in any desired order including
the same tracks.
■You can only make a program when the CD Player is stopped.
1 Insert a CD.
2 Press the CD #/8button.
3 Press the 7button to stop the CD.
SET
Total playback time
EN10-22.UX-V10[U] 00.4.19, 10:48 AM11

12
English
Playing at Random
The tracks will play in no particular order when you use this mode.
Press the RANDOM button on the Remote
Control.
The RANDOM indicator lights up on the display, and tracks will
be played in random order.
To skip a track during playback, press the ¢button (or the
> or UP button on the Remote Control) to jump to the next
randomly selected track. Press the 4button (or the < or DOWN
button on the Remote Control) to jump back to the start of a track
being played.
To exit from Random Play mode, press the 7button.
Repeating Tracks
You can set the program or individual track currently playing to
repeat as many times as you like.
Press the REPEAT button on the Remote
Control.
The Repeat indicator changes at each press of the button, as shown
below.
: Repeats one track.
ALL : In Normal Play mode, repeats all the tracks.
In Program Play mode, repeats all the tracks in
the program.
In Random Play mode, repeats all the tracks in
random order.
To exit from Repeat mode, press the REPEAT button until the
Repeat indicator on the display goes out.
■In Random Play cannot be selected.
■Repeat mode remains in effect even when you change the play
mode.
Locking the CD cover
You can lock the CD cover and prohibit to unload the CD.
• This operation is possible only using the buttons on the unit.
To prohibit unloading the CD, press the button while
holding the 7button. (If the CD cover is opened, close it first.)
“LOCKED” appears for a while, and the CD cover is locked.
To cancel the prohibition and unlock the CD cover, press
the button while holding the 7button.
“UNLOCKED” appears for a while, and the CD cover is unlocked.
Note: If you try to unload the CD, “LOCKED” appears to inform
you that the CD cover is locked.
ALL
blank display
EN10-22.UX-V10[U] 00.4.19, 10:48 AM12

13
English
AUTO REVERSE
AUTO TAPE SELECTOR
TAPE
Using the Cassette Deck
(Listening to a Tape)
TAPE @#
4
7
¢
REV. MODE
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
Tape Direction indicator
Reverse Mode indicator
DOWN UPMULTI CONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
The Cassette Deck allows you to play and record audio tapes.
■With Automatic Tape Detection, you can listen to type I, II or
IV tapes without having to change any settings.
The use of tapes longer than 120 minutes is not recommended,
since characteristic deterioration may occur and these tapes
easily jam in the pinch-rollers and the capstans.
One touch play –––––––––––––––––––––––
By pressing the TAPE @#button on the Unit or the Remote
Control, the Unit will come on, “TAPE” appears on the display,
and if a tape is in the deck, it will start to play. If no tape is loaded,
the Unit will come on and wait for you to insert a tape, or select
another function.
Standard Play
When the power is already on, you can use this basic procedure:
1 Press the TAPE 0button on the Unit.
2 When the cassette holder opens, put the
cassette in, with the side you want to
listen to facing up.
• If the cassette holder does not open, turn the Unit off, then
back on and press the TAPE 0button again.
3 Close the holder gently until it clicks.
4 Press the TAPE @#button.
The tape is played in the direction shown by the Tape Direction
indicator.
5 If you need to change the playback
direction, press the TAPE @#button
again.
The other Tape Direction indicator lights up and the tape
playback direction changes.
To stop playing, press the 7button.
To remove the tape,stop the tape, and press the TAPE 0button on
the Unit.
Fast-winding a tape ––––––––––––––––––
■Press the ¢or 4button to fast-wind the tape.
• The Cassette Deck automatically stops when the tape
reaches its end.
Reverse Mode
You can set the cassette deck to play just one side of a tape, both
sides once, or both sides continuously.
Press the REV. (reverse) MODE button on
the Unit.
The indicator changes at each press of the button as shown.
: The Cassette Deck automatically stops after playing both
sides of the tape. (Stops when playback in the 2
direction is finished.)
: The Cassette Deck continues to play both sides of the
tape until the 7button is pressed.
: The Cassette Deck automatically stops after playing one
side of the tape.
TAPE @#
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
¢
7
4TAPE 0
Cassette
holder
EN10-22.UX-V10[U] 00.4.19, 10:48 AM13

14
English
Using the Cassette Deck
(Recording)
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
TAPE @#
7
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
Recording onto a tape from any of the sound sources is simple. Just
place a tape in the Cassette Deck, have the source ready, make one
or two settings, and you’re ready to record. For each source the
procedure is a little bit different so we explain each separately. But
first, here are a few things to make your recordings better.
Things to know before you start
recording –––––––––––––––––––––––––––––
■It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
■When you want to record onto both sides of a tape, you can set
Reverse mode to do so. Recording automatically stops after
recording in the 2direction. Therefore, make sure that the tape
direction is 3when recording with Reverse mode on.
■The recording level, which is the volume at which the new tape
is being made, is automatically set correctly, so it is not
affected by the VOLUME control on the System. Nor is it
affected by adjusting the sound effects. Thus, during recording
you can adjust the sound you are actually listening to without
affecting the recording level.
■Two small tabs on the back of the cassette tape, one for side A
and one for side B, can be removed to prevent accidental
erasure or recording.
■To record on a cassette with the tabs removed, you must cover
the holes with adhesive tape first. However, when a type II tape
is used, only cover part of the hole as shown, since the other
part of the hole (Type II detection slot) is used to detect the
tape type.
■Type I and Type II tapes can be used for recording.
Note: At the start and end of cassette tapes, there is leader tape
which cannot be recorded onto. Thus, when recording CDs
or radio broadcasts, wind on the leader tape first to ensure
that the recording will be made without any music part lost.
CAUTION:
If a recording you make has excessive noise or
static, the Unit may have been too close to a TV
which was on during the recording. Either turn
off the TV or increase the distance between the
TV and the System.
CD #¥8
Adhesive tape
Type II detection
slot
Standard Recording
You can record any sound source to tape as follows:
1 Insert a blank or erasable tape into the
Cassette Deck.
2 If you want to record on both sides of a
tape, press the REV. MODE button on the
Unit until the indicator is lit.
• When using Reverse mode, insert the tape so that it will be
recorded in the forward 3direction.
3 Check the recording direction for the
tape.
Make sure that the Tape Direction indicator is the same as that
for the tape in the Cassette Deck. If the directions are different,
press the TAPE @#button to correct the tape direction and
then press the 7button to stop the tape.
4 Prepare the source by, for example,
tuning in a radio station or turning on
connected auxiliary equipment.
Note: For CD recording, refer to “CD Direct Recording” on page
15.
5 Press the REC button on the Unit.
The REC indicator lights up and the System begins recording.
Notes for using Reverse mode for recording
When recording in Reverse mode, the System automatically stops
when it reaches the end of the reverse 2direction. To record on
both sides of a tape, make sure that the recording direction for the
tape inserted is forwards 3, and that the Tape Direction indicator is
also forwards 3, before you start recording.
To stop at any time during the recording
process
Press the 7button.
7
TAPE @#DOWN UPMULTI CONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
REC
REV. MODE
CD #¥8
RECREC
Tape Direction indicator
Reverse Mode indicator
REC indicator
EN10-22.UX-V10[U] 00.4.19, 10:48 AM14

15
English
CD Direct Recording
Everything on the CD goes onto the tape in the order it is on the
CD, or according to the order you have set in a program.
1 Insert a blank or erasable tape into the
Cassette Deck.
2 Insert a CD.
3 Press the CD #/8button.
4 Press the 7button.
• If you want to record specific tracks only, program the
tracks beforehand.You can check their total playback time
on the display during programing. (See page 11.)
5 If you want to record on both sides of a
tape, press the REV. MODE button on the
Unit until the indicator is lit.
• Make sure that the recording direction for the tape and the
Tape Direction indicator are correct. (See “Notes for using
Reverse mode for recording” on page 14.)
6 Select whether to have pauses left
between recorded selections.
• If nothing is done, a non-recorded pause of about four
seconds will be automatically left between selections.
• If you do not want pauses left between selections, do the
following before proceeding to the next step.
Press the CD #/8button twice.
The CD player enters Pause mode.
7 Press the REC button on the Unit.
The REC indicator lights up and the System begins recording.
• When recording a CD onto tape with Reverse mode on:
If a song is recorded for more than 12 seconds (which
corresponds to the length of leader tape) but not finished
before the first side of tape comes to an end, this song will
automatically be recorded on the second side from its
beginning to avoid being split on both sides.
If a song is recorded for less than 12 seconds before the
first side of tape comes to an end, the song preceding this
song will also be recorded on the second side from its
beginning as it may not be completely recorded on the first
side because of leader tape.
• After the CD player has played the entire CD, or all the
programed tracks, the tape automatically stops.
To stop at any time during the recording process, press
the 7button. The tape stops after 4 seconds.
Note: When making SLEEP timer settings while doing CD Direct
recording, set enough time to allow for the CD to finish
playing, otherwise the power will go off before recording is
completed.
One track recording––––––––––––––––––
1 Insert a blank or erasable tape into the
Cassette Deck.
2 Play the track on the CD you wish to
record.
3 Press the REC button on the Unit.
The CD player returns to the beginning of that track and the
track is recorded on the tape. After recording, the CD player
and Cassette Deck automatically stop.
EN10-22.UX-V10[U] 00.4.19, 10:48 AM15

16
English
Using External Equipment
Listening to External
Equipment
You can connect various external equipment.
For Hong Kong, the external equipment is used as playback and
recording device. For the other areas, it is used only as a playback
device.
■First make sure that the external equipment is properly
connected to the System. (See page 4.)
1 Set the VOLUME control to the minimum
position.
2 Press the AUX button.
“AUX” appears on the display.
3 Start playing the external equipment.
4 Adjust the VOLUME control to the desired
listening level.
5 Apply sound effects, if you wish.
■Press the AHB PRO button to reinforce the bass sound.
■Press the BASS/TREBLE button on the Remote Control to
control the tone. (See “Controlling the Tone (Bass/Treble)” on
page 7.)
To exit from AUX mode, select another source.
Notes:
• For operation of the external equipment, refer to its
Instructions.
• For recording from the external equipment, refer to “Standard
Recording” on page 14.
DOWN UPMULTICONTROL
TAPE FM/AM CD
STANDBY
PHONES
AUX
REC
REV
MODE
AHB
PRO
TIMER
CLOCK
VOLUME
CD
OPEN/CLOSE
AUX
AUX
Recording the System’s
Source to External Equipment
(For Hong Kong only)
You can record the System’s sources to external equipment which
is connected to the LINE OUT or OPTICAL DIGITAL OUT
terminals of the System, such as cassette deck or MD recorder, etc.
■First make sure that the external equipment is properly
connected to the System. (See page 4.)
Play the System’s CD Player or Cassette
Deck, or tune into a station.
■The recording level is not affected by theVOLUME level. It is
not affected by any sound effect, either.
Note: For operation of the external equipment, refer to its
Instructions.
REMOTE CONTROL RM-SUXV10E
CANCELTREBLE
FM/AM
FM
MODE
DISPLAYSLEEP
AUX
TAPE CD
CD
BASS
AHB
PRO
DOWN
RANDOM
UP
AUTO
PRESET
REPEAT
SET
PROGRAM
VOLUME
VOLUME +, –
AHB PRO TREBLE
BASS VOLUME +, –
AHB PRO
EN10-22.UX-V10[U] 00.4.19, 10:48 AM16