JVC LT-40C590 User manual

• Do not connect the TV to the mains supply until you have completed all the connections.
• If you watch TV using a set-top box, simply connect your TV and set-top box via a HDMI cable and select HDMI in the Input Source menu.
Unpacking
1Connecting the Aerial and the Mains Socket
4
Operating Your Remote Control
2
If items are missing, or damaged please contact Partmaster (UK only).
Tel: [phone] for assistance.
Installing the Base Stand
3
Quick Start Guide
40” LED FULL HD TV
LT-40C590
Thank you for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.
Remove all packaging from the TV. Retain the packaging. If you
dispose of it please do so according to any local regulations.
1. Lay the TV down on a flat surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a towel or thick piece of foam) is placed beneath the screen. Leave the protective bag on your TV until you
have fully attached the TV stand.
2. Attach the TV stand to the TV. Align the screw holes, then secure with a screw driver (not included) using the 4 screws provided.
Installing Batteries
1. Press and lift the back
cover to open the
battery compartment of
the remote control.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
Operation Range
Point the remote control
at the TV no more than 5
metres from the remote
control sensor on the TV and
within 60° in front of the
TV. The operating distance
may vary depending on the
brightness of the room.
1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the RF (75Ω) socket at the rear right side of your
TV.
2. Connect the mains cable to the mains socket after you have completed all the connections.
3. At this stage, the TV switches to standby mode. The red LED indicator will illuminate on the front panel of the TV.
4. In standby mode, press the button on the bottom of the TV or on the remote control to turn the TV on. The red LED indicator will turn off.
The latest eco-friendly power-saving technology will switch o the TV if device is
left on and idle for 4 hours or it does not receive an input signal for serveral minutes.
Please refer to“Eco Friendly / Auto Standby Function” section of the instruction manual
for more detail.
For Help and Support Call
UK: 0344 561 1234
Ireland: 1890 818 575
1
2
RF
COMMON INTERFACE (CI)
HEADPHONES
Digital Audio Output
(optical)
RF coaxial cable
(not included)
OR
To the mains socket
SETUP
ANGLE
ZOOM STEP
MENU
TEXT
CANCEL
AUDIO
MIX
OK
SIZE
ASPECT S.MODE P.MODE GUIDE
LIST
PROG
MENU INPUT
BACK EXIT
OK
S
TITLE
TV.RD
FAV
HOLD REVEAL SUBPAGE INDEX
GOTO SLOW REPEAT A-B
TV
Remote Control AAA Batteries x 2
Quick Start Guide
TV Stand Base Screw x 4
Instruction Manual
SETUP
ANGLE
ZOOM STEP
MENU
TEXT
CANCEL
AUDIO
MIX
OK
SIZE
ASPECT S.MODE P.MODE GUIDE
LIST
PROG
MENU INPUT
BACK EXIT
OK
S
TITLE
TV.RD
FAV
HOLD REVEALSUBPAGE INDEX
GOTO SLOW REPEAT A-B
30° 30°
5M
Install the batteries correctly by following the polarity (+ and -) indications in the
battery compartment.
TV Stand Base Front
(included)

Turning the TV On for the First Time
5Target Region Setting (UK only) 6
The first time you turn the TV on, it will go straight into the First Time Installation menu. During tuning your TV may have received signals from more than one transmitter. If this has occurred the Target Region Setting screen will be displayed. This
will enable you to select the correct regional transmission for the local news service that you require.
1. Press the buttons to select the Country then press the buttons to select Primary
Region / Secondary Region / Tertiary Region.
2. Press the buttons to select your preferred region then press the OK button to confirm.
Country Code This will be shown as GBR for the UK.
Primary Region This will show the regional country (e.g. England, Wales, Scotland, NI).
Secondary Region This will allow you to set the region for your local news service on BBC and
ITV (e.g. London, Beds and Cambs etc).
Tertiary Region You may receive signals from more than one transmitter within the
Secondary Region, (e.g Beds and Cambs may have Luton or Sandy Heath).
1. Please ensure the aerial is plugged in and then press the OK button.
5. Press the button to select Tune Type, then press the buttons to select DTV /
ATV / DTV + ATV. Press the OK button to confirm.
2. Press the buttons to select the country where you will operate the TV. Press the
OK button to confirm.
3. Press the button to select OSD Language, then press the buttons to select
your desired language to be displayed on the menu. The default on-screen menu
language is set as English. Press the OK button to confirm.
If you are going to watch TV using a set-top box, press the EXIT button on the remote control
then skip this section. Then press the INPUT button on the remote control to select HDMI mode.
4. Press the button to select Home/Store Mode. Press the buttons to select your
desired mode and then press the OK button. A pop-up message will be displayed.
Press the buttons to select Yes to confirm or No to cancel. Press the OK button to
return to the Mode Select menu.
Home Mode Intended for use in home environment.
Store Mode Intended for use in retail environment.
Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call:
• UK Call Centre on 0344 561 1234. • Ireland Call Center on 1 890 818 575.
(QSG-LT-40C590-210510V5)
First Time Installation
Please ensure aerial is plugged in!
Confirm
OK
First Time Installation
Country UK
Confirm
OK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
First Time Installation
Country UK
Confirm
OK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
First Time Installation
Country UK
Confirm
OK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
First Time Installation
Country UK
Confirm
OK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
Channel Tuning
TV Channel(s)
DTV UHF 36
DTV Channel(s)
Radio Channel(s)
Data Channel(s)
0
0
0
0
6. Channel tuning will commence. This operation may take a few minutes. The display
will show the progress of the tuning and the number of channels found.
Choose Your Prefered Region
Country
Primary Region
Secondary Region
Tertiary Region
UK
England
London
Cambridge
Confirm
OK