JWA SAN BERNARDO 70590 User manual

ASSEMBLY INSTRUCTION
SAN BERNARDO
70590
DOUBLE BED
1
Imported by JWA Furn ture Pty Ltd, Qld, Br sbane Austral a.
For any ass stance w th assembly or for m ss ng parts please refer to your rece pt

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spac ous assembly area. Avo d hard surfaces that may damage the
product
2.Take care when l ft ng. Product should be assembled as near as poss ble to the po nt of
use
3.Ensure that you have all requ red contents for complete assembly
4.Always read the assembly nstruct ons carefully before beg nn ng assembly.
5.Keep all hardware parts and packag ng out of reach of small ch ldren.
6.Do not over t ghten the screws and bolts as th s may damage the threads
7.Assembly s to be carr ed out by a competent adult(s) ONLY
8.Dur ng assembly, ch ldren should be kept away from the product due to poss ble r sk to
njury.
9.Do not use th s tem f any components are m ss ng or damaged.
10.Please keep the nstruct ons for future reference.
2
Allow 30 m n For 2 person Add t onal tools
requ red

PARTS LIST
1 Headboard x 1pc 7 Centre Ra l x 1pc
2 Footboard x 1pc 8 Support Leg x 2pcs
3 Head Post x 2pcs 9 End Cap x 24pcs
4 Foot Post x 2pcs 10 Centre Cap x 12pcs
5
S dera l
x 2pcs
11
Slat
(678mm)
x 24pcs
3
5
S dera l
x 2pcs
11
Slat
(678mm)
x 24pcs
6 Cross Ra l x 2pcs

STEP 1:
•Prepare a protected surface w th a blanket or cardboard.
•Attach headboard(1) to the head post(3). Secure w th 2x bolt(G)
per s de. Fasten w th Allen Key(F).
•Repeat for the footboard(2) and foot post(4).
•Connect a s de ra l(5) to the headboard and footboard. Secure
w th 2x bolt(B) per corner. Fasten w th allen key(F).
•Repeat for the other s de ra l.
4

STEP 2:
•Attach the 2x supports(8) to the centre ra l(7), as shown below.
Use 2x bolt(A) per leg, threaded from the top, and lock w th
nut(E). Fasten w th allen key(F) and hold the nut w th a pa r of
pl ers.
•Attach the cross ra ls(6) near the headboard and footboard, as
shown below. Thread bolt(C) from the top on every corner, and
lock w th nut(E). Fasten w th allen key(F) and hold the nut w th a
pa r of pl ers.
•Attach the centre ra l(7) to the cross ra ls(6), as shown below.
Thread 2x bolt(D) from the top, n the m ddle of each cross
ra l(6), and lock w th nut(E). Fasten w th allen key(F) and hold the
nut w th a pa r of pl ers.
5

STEP 3:
•Attach an end cap(9) onto every slat, 1 per slat(11).
•Take 2x slats and cup the non capped end nto e ther s de of
the m ddle cap(10). Form 12x slat pa rs.
•Attach the slat pa rs to the bed as shown below. Push the caps
nto the holes.
6

Assembly Is Complete
7

PRODUCT CARE:
FURNITURE / BED
1. When assembling your furniture / bed please ensure that you have
checked the contents for all relevant parts.
2. When tightening bolts make sure that they are fully tightened but not
forced.
3. When moving your fully assembled bed you must first remove the
mattress and lift the frame into position, take care when lifting and
always have two people handling the bed. PLEASE DO NOT DRAG THE
BED as this will cause damage to the rail.
4. It is advisable to use approved cleaning products when cleaning the
furniture and bed frame as certain chemical based cleaners could have
an adverse effect on the bed finish.
8