Könner & Söhnen KS 7HP-850A User manual

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
12 3 4 5 6 7 8 9 10 11 12 13 14 15
Please read the assembly instruction carefully before
getting started!

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 1. General view of the KS 7HP-850A gasoline cultivator during
preparation for assembly.
123 4 5 6 7 8 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 2, Fig. 3. Secure the control handle to the cultivator frame with screws.
1 2 34 5 6 7 8 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 4. Install the transport wheel. To do this, fix the spring on the locking
pin and pass the latter through the groove in the cultivator frame and the
hole in the support foot of the transport wheel. Secure the locking pin
with a cotter pin.
Fig. 5. Attach the other end of the spring to the locking pin with pliers,
and then pass the locking pin through the holes in the cultivator frame
and in the support foot of the transport wheel. Secure the locking pin
with a cotter pin.
1 2 3 45 6 7 8 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 6. This is how the spring fixed in the cultivator frame looks like.
Fig. 7. General view of the fixed transport wheel.
1 2 3 4 56 7 8 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 9. Secure the locking pin with a cotter pin.
Fig. 8. Install the plow holder mount on the cultivator frame with the
locking pin.
1 2 3 4 5 67 8 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 11. Adjust the plow holder to the desired plowing depth. Secure it
with a locking pin and cotter pin.
Fig. 10. Adjust the angle of rotation of the plow holder mount and fix it
with screws. Secure the selected position with a locknut.
1 2 3 4 5 6 78 9 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 12. Place an assembled cutter set* on the cultivator axle. Secure the
cutters with a locking pin.
Fig. 13. Secure the fender to the cultivator with bolts and nuts.
*The sequence for assembling the cutters can be found
at the end of this instruction.
1 2 3 4 5 6 7 89 10 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 15. Install the protective cover on the cultivator body.
Fig. 14. Image of a cultivator belt drive.
1 2 3 4 5 6 7 8 910 11 12 13 14 15

KS 7HP-850A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 16. Secure the protective cover to the cultivator body with screws.
Fig. 17. General view of the assembled KS 7HP-850A cultivator.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 1. General view of the semiaxle for cutters, assembled and
disassembled.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 2. Each cutter (left and right) consists of several sections. The cutting
edge of the knives should be at the front (in the direction of travel of the
cultivator).
Fig. 3. Assemble the cultivator's left cutters. The left knives have their
cutting edge against the user pointing to the left, with the right knives
having their cutting edge against the user pointing to the right.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
3
2

CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 4. Attaching knives using the example of one of the sections of the
left cutter. Attach the 2 left knives to the outside of the base so that the
bends point to the left opposite each other.
Fig. 5. Attach the 2 right knives to the inside of the base so that the bends
point to the right opposite each other. The cutting edge of all knives
should be at the front (in the direction of travel of the cultivator).
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 6. Secure the knives with screws and nuts.
Fig. 7. Connect the sections together using locking pins, and then secure
the locking pins with cotter pins.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 8. General view of the assembled left cutter. Each section should
be fixed on an axle with an offset from the previous one by 45 degrees
clockwise.
Fig. 9. The right cultivator cutters are mounted inversely. The cutting
edge of the knives should be at the front in the direction of travel of the
cultivator.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
8
9