Könner & Söhnen KS 7HP-950A User manual

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
12 3 4 5 6 7 8 9 10 11 12 1413
Please read the assembly instruction carefully
before getting started!

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 1. General view of the KS 7HP-950A gasoline cultivator during
preparation for assembly.
123 4 5 6 7 8 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 3. Secure the locking pin with a cotter pin.
Fig. 2. Install the plow holder mount on the cultivator frame with the
locking pin.
1 2 34 5 6 7 8 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 4. Adjust the angle of rotation of the plow holder mount and fix it
with screws and nuts. Secure the selected position with a locknut.
Fig. 5. Mount the transport wheel on the cultivator frame. Secure the
wheel with a locking pin and cotter pin.
1 2 3 45 6 7 8 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 6. Cultivator frame.
Fig. 7. Lock the position of the control handle with the clamp fixture.
1 2 3 4 56 7 8 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 8. Fasten the protective cover with the screw to the joints of the
cultivator frame and the control handle.
Fig. 9. Secure the fender to the cultivator with bolts and nuts.
1 2 3 4 5 67 8 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 10. Install the shift lever.
Fig. 11. Secure the shift lever extension with a locking pin, and then secure
the locking pin with a cotter pin.
1 2 3 4 5 6 78 9 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 12. Secure the protective cover to the cultivator body with screws.
Fig. 13. Place an assembled cutter set* on the cultivator axle. Secure the
cutters with a locking pin.
*The sequence for assembling the cutters can be found at
the end of this instruction.
1 2 3 4 5 6 7 89 10 11 12 1413

KS 7HP-950A GASOLINE
CULTIVATOR ASSEMBLY
INSTRUCTION
Fig. 14. Secure the support strip to the fenders from below with screws
and nuts.
Fig. 15. General view of the assembled KS 7HP-950A cultivator.
1 2 3 4 5 6 7 8 910 11 12 1413

1 2 3 4 5 6 7 8 9 10 11 12 1413
CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 1. General view of the semiaxle for cutters, assembled and
disassembled.

1 2 3 4 5 6 7 8 9 10 11 12 1413
CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 2. Each cutter (left and right) consists of several sections. The cutting
edge of the knives should be at the front (in the direction of travel of the
cultivator).
Fig. 3. Assemble the cultivator's left cutters. The left knives have their
cutting edge against the user pointing to the left, with the right knives
having their cutting edge against the user pointing to the right.
3
3

1 2 3 4 5 6 7 8 9 10 11 12 1413
CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 4. Attaching knives using the example of one of the sections of the
left cutter. Attach the 2 left knives to the outside of the base so that the
bends point to the left opposite each other.
Fig. 5. Attach the 2 right knives to the inside of the base so that the bends
point to the right opposite each other. The cutting edge of all knives
should be at the front (in the direction of travel of the cultivator).

1 2 3 4 5 6 7 8 9 10 11 12 1413
CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 6. Secure the knives with screws and nuts.
Fig. 7. Connect the sections together using locking pins, and then secure
the locking pins with cotter pins.

1 2 3 4 5 6 7 8 9 10 11 12 1413
CULTIVATOR CUTTERS ASSEMBLY
INSTRUCTION
Fig. 8. General view of the assembled left cutter. Each section should
be fixed on an axle with an offset from the previous one by 45 degrees
clockwise.
Fig. 9. The right cultivator cutters are mounted inversely. The cutting
edge of the knives should be at the front in the direction of travel of the
cultivator.