Kaboodle W-51643 User manual

Wall fixing
(If necessary)
Hardware included
A
32mm
tek screws x 4
B B
12mm
bolt x 12
70mm
wood screws x 10
Tools you will need
To put your kaboodle steel frame shelving together you will need the following tools.
C
Cordless drill with:
• Number 2 screw tip
• 3.5mm HSS drill bit
• 4.5mm HSS drill bit
Clamps
(quick release)
Cabinet Stand
Recommended
Phillips head
srewdriver
D
32mm
wood screws x 8
Things you need to know
Tape
measure
Adjustable
square
Safety
gearPencil
step 2
Spirit level
(900mm recommended)
p. 1Ver. 1
W-51643
W-51644
• All cabinets will need to be attached to the wall using a
minimum of 8 gauge 65mm screws if you have a stud wall.
If your wall is concrete, brick or another surface ask your
hardware specialist for advice on the right fixing method.
• Make sure you leave plumbing and electrical work
to qualified trades people. Never try this yourself.
• Make sure you always use safety gear like a mask, ear muffs
and glasses when using tools.
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
Follow these
instructions to
build and attach
your steel frame
shelves.
wall steel frame shelving
Stud
finder

1.
step 2
hardware key
p. 2Ver. 1
W-51643 / W-51644
12mm
bolt
B C
32mm
tek screw
2.
Note: If the frame is being installed
underneath a wall cabinet or bulkhead, the
top rails can be flipped upside down so that
the shelf support can be screwed through
as a fixing point.
Note: The middle rail brackets are not in the
centre of the frame end - this is so that the
wall frame will line up with the slim frame if
used together. Ensure the rail brackets on
each frame end align before installing.
Slide all horizontal
support rails
on to frame ends.
top rails
support rails
wall steel frame shelving
assembling frame
Use bolts provided to assemble the frame.
Note: Ensure frame is assembled square
as there can be some play in the joins.
rear support rails
joining frames
3. 4.
2.
If you are using 2 or
more steel frames in a run,
join them together before mounting
to the wall. On a perfectly flat and level
surface, clamp the units together and mark
out 4 drill points on the cross bars of the
frame end. Use a 3.5mm HSS (steel drill-
ing) drill bit to drill through one frame end
and halfway into the tube of the adjoining
frame end.
Use four 32mm tek screws provided to
secure frames together. WARNING: Screws
are provided to keep frames aligned and
will not support significant weight. Be
careful lifting and moving joined frames.
1.
2.
stud
Use a stand or mounting rail to sit the
frame in position and mark the location
of the stud on all rear support rails.
Ensure the frame is sitting square and
level while doing this to avoid installing
the frame crooked.
fixing frame to wall
Use a stud finder to locate and mark
the centre point of any stud that will be
behind the frame. 2 studs are required
to secure the frame, or one stud and a
secure cabinet or wall to fix to sideways.
1.
C
Sit the frame in position ensuring it is still
square and level, and use the holes in the
support rails to mark the wall.
Remove the frame and drill holes into the
studs in the marked locations using a 3.5mm
drill bit to a depth of 50mm.
Use a 4.5mm HSS (steel drilling) drill bit to
drill through the centre of each support rail
in the marked locations of each stud.
centre hole
B

A D
70mm
wood screws
32mm
wood screws
step 1
step 2
step 3
step 4
wall steel frame shelving
step 2
hardware key
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail] p. 3Ver. 1
W-51643
W-51644
Note: If the frame adjoins another cabinet
or a side wall - mark and pre-drill the frame
prior to wall mounting, then once the
frame is fixed to the rear wall fasten to the
adjoining cabinet or side wall using either
the 70mm (wall fixing) or 32mm (cabinet)
wood screws provided.
Once your frame is fixed securely in place,
insert the shelves to complete the unit.
Note: You can replace the provided shelves
with other 16 or 18mm thick shelves of suit-
able material. To match the finish of your
kaboodle doors, purchase multi-purpose
panels in the same colour through the
kaboodle cut service.
1.5.
installing shelves
Screw the frame into the wall studs
using the 70mm screws provided.
Ensure the frame is fixed securely
and is square and level.
shelf
shelf
shelf
Caring for your kaboodle parts and accessories
Looking after your cabinets is really easy and with the right care and maintenance they
will last you for many years. Just follow these simple steps and if you need any more
information you can contact us on 1800 666 078 Monday to Friday between 8:00am
and 6:00pm AEST or email: [e-mail].
Hinges, runners and other parts and accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry cloth
removing any dust and grime that may build up.
Then follow the
instructions to fit
your doors and
panels.
Your Kaboodle
cabinet is now
complete.
Next grab your
parts and
accessories
instructions.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
C
D