Kaboodle 400mm wall cabinet User manual

Wall fixing
(If necessary)
Tools you will need
To put your kaboodle kitchen cabinets together you will need the following tools.
Hardware included
EC DBA
stick on end
caps x 5
28mm
wood screws x 5
door
buffer x 2
shelf
support x 4
50mm
wood screws x 18
Things you need to know
Cordless drill with:
• Number 2 screw tip
• 4mm drill bit
• Number 12
countersinking drill bit
Tape
measure
Adjustable
square
65mm
wood screw
Safety
gearPencil
step 1
Follow these
instructions to
build and attach
your cabinet.
• All cabinets will need to be attached to the wall using a
minimum of 8 gauge 65mm screws if you have a stud wall.
If your wall is concrete, brick or another surface ask your
hardware specialist for advice on the right fixing method.
• Make sure you leave plumbing and electrical work
to qualified trades people. Never try this yourself.
• For extra strength use exterior woodworking glue
when assembling cabinets.
• To help identify panels, counter sunk holes always
face outwards.
• All holes that aren’t already pre-drilled should be drilled prior
to screwing using a No 12 countersinking drill bit.
• Make sure you always use safety gear like a mask, ear muffs
and glasses when using tools.
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
Spirit level
(900mm recommended)
p. 1Ver. 9
W-51622
Clamps
(quick release)
400mm wall cabinet
Cabinet
Stand

step 1
hardware key
A
p. 2Ver. 9
W-51622
2.1.
shelf
support
C
50mm
wood screws
3.
assembling cabinet
Cabinet complete R
400mm wall cabinet
C
A
back panel
back panel
top panel
top panel
top panel
bottom
panel
bottom
panel
Cabinet frame now complete R
side panel
side panel
side panel
A
A
2.1. 3.
Installing adjustable shelf

stud
plaster board
step 1
step 2
step 3
step 4
28mm
wood screws
400mm wall cabinet
B
Then follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
Next grab your
parts and
accessories
instructions.
Your Kaboodle
cabinet is now
complete.
step 1
hardware key
p. 3Ver. 9
W-51622
Caring for your kaboodle cabinets
Looking after your cabinets is really easy and with the right care and maintenance they
will last you for many years. Just follow these simple steps and if you need any more
information you can contact us: Australia: 1800 666 078 Monday to Friday between 8:00am
and 6:00pm AEST. New Zealand: 0800 522 663 Monday to Friday between 8:00am and
5:00pm NZST or email: [e-mail].
Clean your cabinets with an all purpose, non-abrasive cleaner with a damp sponge or cloth
and make sure you never use saturated cloth, harsh chemicals or thinner based cleaners
as these will damage the surface of the melamine. Likewise, never use products that will
scratch the surface like steel wool or wire brushes and avoid sharp objects that will scratch,
cut or gouge the melamine surface. If this happens the internal board will be exposed and
may swell. Kaboodle cabinets are water resistant but not water proof so any spills should
be attended to immediately.
Handy hint: if the melamine surface of your cabinet is damaged you can try and cover it
with a furniture repair crayon but just remember that this won’t seal the board back to its
original finish.
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]
Check all cabinets are level then pre-drill
and screw cabinets together.
1.2.1.
joining cabinets fixing cabinets to wall
When you need to add an end
panel check out the end panel
instructions for installation tips.
Caution: Please ensure all cabinets are
screwed into your timber stud wall using
a minimum of 65mm timber screws.
If attaching to concrete, brick, steel or
any other substrates seek advice from
your hardware specialist.
With the aid of cabinet supports align
cabinets and hold together using clamps.
Tip: If a pantry has been installed, align
wall cabinets to the height of the pantry.
Note: AS/NZ standards states that the
distance between the benchtop and
wall cabinet needs to be a minimum
of 450mm.
B