Kaboodle W-50531 User manual

*bracket x 4
*May be required
when using cabinets
dierent to Kaboodle
runners x 1 pair 14mm
wood screws x 4
EC DBA G
m4 8mm
screws x 4
bin
frame x 1
16mm
wood screws x 12
lid
brackets x 2
Hardware included
p. 1Ver. 2
W-50531
Tools you will need
To put your kaboodle kitchen waste bins together you will need the following tools.
Cordless drill with:
• Number 2 screw tip
• 2mm drill bit
Tape
measure
Adjustable
square
Clamps
(optional)
Spirit level
(optional)
Screw
driver
Safety
gearPencil
Follow these
instructions to
install your parts
and accessories.
Things you need to know
• Always read the full instructions prior to installation.
• Consider possible obstructions to your parts & accessories,
like hinges inside the cabinet or adjacent cabinet doors and
handles, prior to installation.
• Make sure you leave plumbing and electrical work
to qualified trades people. Never try this yourself.
• Make sure you always use safety gear like a mask, ear mus
and glasses when using tools.
• Tip: After marking out the pre-drill holes as per the
instructions, take the part that is to be installed and align
the appropriate holes with the markings to ensure they
match up prior to pre-drilling the holes.
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
2x31L side mount pullout bin
step 2
installation guide

kaboodle.com.au
A
hardware key
B
3.
A
(i)
(ii)
runners x 1 pair
A
p. 2Ver. 2
W-50531
step 2
1.
477mm
422mm
422mm
477mm
192mm
37mm
37mm
288mm
229mm
229mm
400mm
475mm
475mm
400mm
288mm
192mm
16mm
wood screws
pre-drilling for runners
separating runners attaching runners
pre-drilling for lid brackets
3.
2.
4.
2 x 31L side mount pullout bin
B
A
On both sides of your cabinet, draw a horizontal line 477mm up
from the bottom. Measuring from the front of the cabinet along
these lines, mark out the pre-drill holes at 192mm, 288mm and
400mm as pictured above. Use a 2mm drill bit to pre-drill holes
to a depth of roughly 2.5mm.
Separate each runner (A) into two parts by extending the guide
(i) and pushing up on the lever (ii) while continuing to pull apart
the two components. The guide should separate easily from the
runner without too much force being applied.
Using the lower sets of pre-drilled holes, align with the holes
on the runners (A) and fix to the cabinet using 6 x 16mm wood
screws (B) as pictured above.
On both sides of your cabinet, draw a horizontal line 422mm up
from the bottom. Measuring from the front of the cabinet along
these lines, mark out the pre-drill holes at 37mm, 229mm and
475mm as pictured above. Use a 2mm drill bit to pre-drill holes
to a depth of roughly 2.5mm.

hardware key
CB
lid brackets
16mm
wood screws
E
m4 8mm
screws
p. 3Ver. 2
W-50531
step 2
7. 8.
attaching lid brackets
5. 6.
BC
Using the top sets of pre-drilled holes, align with the 2nd, 5th
and 7th holes on the lid brackets (C) and fix to the cabinet using
6 x 16mm wood screws (B) as pictured above.
2 x 31L side mount pullout bin
Position the door fixing brackets so the elongated holes on
each bracket align with the holes drilled in Step 7. Ensure the
open side of the brackets face inward as pictured above.
Fix the brackets to the door using 4 x 14mm wood screws (F).
Measure from the bottom of door. Mark out and pre-drill four
holes on the back of your cabinet door as pictured above.
Use a 2mm drill bit to pre-drill holes to a depth of roughly 2.5mm.
Carefully slide the guides back into the runners. The runners should
open and close smoothly if assembled correctly. Extend the runners
once they have been correctly reassembled.
36.5mm
36.5mm
305mm
305mm
410mm
410mm
F
F
attaching door brackets reassembling runners
pre-drilling for door

hardware key
E
m4 8mm
screws
D
bin frame
p. 4Ver. 2
W-50531
step 2
attaching door panel
11.
9. 10.
2 x 31L side mount pullout bin
Slide the back plastic catches of the bin lid along the
top of the lid brackets until both plastic catches fall into
the channels at the back. The front two plastic catches
should fit into the front channels at the same time.
Place the bin frame (D) carefully onto the extended runners,
aligning the holes and then securing into place with the 4 x M4
8mm screws (E). Note: Support the runners from underneath
when screwing the frame into place. Do not tighten screws.
ED
inserting bin lidattaching bin frame
The door can be adjusted
vertically by turning screw on
bottom of bracket up or down.
The depth of the door can be
adjusted by loosening o middle
screw and adjusting top/bottom
screws and then re-tightening
middle screw.
The door can be
adjusted horizontally by
loosening the screws in
the elongated slots and
moving door sideways.
Note: Loosen o screws highlighted above before making
any adjustments to the door. Once adjustments are completed,
these screws must be tightened again.

step 1
step 2
step 3
step 4
Next, follow the
instructions to fit
your doors and
panels.
Finish o your
Kaboodle Kitchen
by installing your
benchtop.
You’ve finished
adding your
parts and
accessories.
Your Kaboodle
cabinet is now
complete.
step 2
p. 5Ver. 2
W-50531
12.
installing bins
2x31L side mount pullout bin
Place the bins into the frame to complete assembly.
Note: Max weight capacity, including door if attached, is 25kg.
Caring for your kaboodle parts and accessories
Looking after your cabinets is really easy and with the right care and maintenance
they will last you for many years. Just follow these simple steps and if you need any
more information you can contact us: Australia: 1800 666 078 Monday to Friday
between 8:00am and 6:00pm AEST. New Zealand: 0800 522 663 Monday to Friday
between 8:00am and 5:00pm NZST or email: [e-mail].
Hinges, runners and other parts and accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry
cloth removing any dust and grime that may build up.
We oer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]