Kaboodle W-50541 User manual

Tools you will need
To put your kaboodle kitchen accessory together you will need the following tools.
Hardware included
Things you need to know
E FC DB
H
A
G
p. 1Ver. 9
W-50541
Cordless drill with:
• Number 2 screw tip
• 2mm drill bit
Tape
measure
Adjustable
square
Clamps
(optional)
Spirit level
(optional)
Screw
driver
Safety
gearPencil
Follow these
instructions to
add your parts
and accessories.
22mm
wood screws x 16
connect strip x 2
runner protective
covers x 2
U-Iron x 1
16mm
wood screws x 16
L- B ra c k et x 1runners x 1 pair L-Irons x 2
• Always read the full instructions prior to installation.
• Consider possible obstructions to your part and accessories,
like hinges inside the cabinet or adjacent cabinet doors
and handles, prior to installation.
• Make sure you leave plumbing and electrical work
to qualified trades people. Never try this yourself.
• Make sure you always use safety gear like a mask, ear muffs
and glasses when using tools.
• This accessory is designed to be installed in cabinets
with either a left hand or right hand opening set up.
• Tip: After marking out the pre-drill holes as per the
instructions, take the part that is to be installed and align
the appropriate holes with the markings to ensure they
match up prior to pre-drilling the holes.
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
450mm pantry pullout baskets 6 tier
step 2

hardware key
A AA CB
step 2
p. 2Ver. 9
W-50541
1.
attaching the L-Irons attaching the L-bracket and frame
Remove two flat head screws from each L-Iron (A) and attach
to the runners (B) as pictured above. NOTE: You will need to slide
the runner forward (i) and backward (ii) to access the round holes
of the runners. Be sure to screw through the runner to the L-Iron
as above.
(i) Remove 2 screws from the back of the frame at the top,
insert the L-Bracket and fix into place with the 2 screws
as pictured above (i). NOTE: It is not necessary to fully
tighten the screws at this stage as they will be adjusted
at a later stage.
(ii) Remove the top 2 screws on each L-Iron and attach to the
frame. Be sure to screws through the frame to the L-Iron
as pictured above (ii).
Mark out and pre-drill four holes on the bottom panty panel
as per the diagram above. Use a 2mm drill bit to pre-drill
holes to a depth of 2.5mm.
Mark out and pre-drill four holes on the top panty panel as
per the diagram above. Use a 2mm drill bit to pre-drill holes
to a depth of 2.5mm.
For left hand open, simply mirror the measurements above.
right open
shown
back
front
220mm
152mm
152mm
488mm 488mm
478mm
170mm
428mm
30.5mm
62mm
62mm
L- B r a c k e trunners pair L-Irons
pre-drilling holes (top) pre-drilling holes (bottom)
4.3. (i)
(ii)
(ii)
2.
A
B
C
top pantry panel
bottom pantry panel
right open shown
back view
450mm pantry pullout baskets 6 tier
(i)

hardware key
AAD FE
step 2
p. 3Ver. 9
W-50541
adjusting the L-Bracket installing protective covers
Loosen the 2 screws at the back of the frame (i). Adjust the
L-Bracket up so the castors are slotted into the U-Iron completely
and tighten screws (i).
Align the U-Iron (E) with the pre-drilled holes and using 4 x 16mm
wood screws (D), fix the U-Iron to the top of the cabinet.
attaching the runners attaching the U-Iron
runner protective
covers
U-Iron
16mm wood
screws
Align the runners with the pre-drilled holes and using 4 x 16mm
wood screws (D), fix the runners to the bottom of the cabinet.
Secure the runners using a further 8x16mm wood screws,
ensuring the screws are spaced evenly on both runners
and are mirrored from the left to the right side.
5.
8.7.
6.
D
D
E
F
W-50541
450mm pantry pullout baskets 6 tier
front of cabinet
front of cabinet
back of cabinet
front of cabinet
back of cabinet
Slide the protective covers (F) over the runners below the frame
as pictured above.
(i)
right open
shown

hardware key
AG H
step 2
p. 4Ver. 9
W-50541
connection
strip
22mm
wood screws
attaching door rack installing connecting strips
9. 10.
66mm
(min)
66mm
(min)
100mm
(max)
100mm
(max)
110mm 110mm
166mm 166mm
315mm
315mm
Attach the door to the cabinet. NOTE: If not a retro-fit installation
you will need to install your hinges at this point.
Remove the 2 screws from one end of the connecting strip (H),
align with appropriate holes on the frame and fix into place as
pictured above (i). NOTE: Take care not to misplace any parts.
Next remove the screw from the other end of the connecting
strip, align with the hole at the end of the door rack panel and fix
into place as pictured above (ii).
450mm pantry pullout baskets 6 tier
On the back of your pantry door, draw a level line the length
of the door 66-100mm from the inside edge. Next draw a second
line the length of the door 315mm over from the first line.
Measuring from the bottom of the door along these lines, mark
out the pre-drill holes at 110mm and 166mm as pictured above.
Use a 2mm drill bit to pre-drill holes to a depth of roughly 2.5mm.
Align the door rack panels with the pre-drilled holes and fix into
place using 4x22mm wood screws (G) as pictured above. Then
using the remaining 12 wood screws secure the door rack panels
to the door taking care not to damage the front side of the door.
NOTE: For retro-fit installations you will need to unclip your hinges
to remove the pantry door and carefully place on a flat, clean
surface before marking out the pre-drill holes.
(ii)
(ii)
(i)
(i)
right open
shown

step 1
step 2
step 3
step 4
Then follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
Next grab your
parts and
accessories
instructions.
Your Kaboodle
cabinet is now
complete.
step 2
p. 5Ver. 9
W-50541
11.
installing the baskets
Caring for your kaboodle cabinets
Looking after your cabinets is really easy and with the right care and maintenance they will last
you for many years. Just follow these simple steps and if you need any more information you can
contact us: Australia: 1800 666 078 Monday to Friday between 8:00am and 6:00pm AEST. New
Zealand: 0800 522 663 Monday to Friday between 8:00am and 5:00pm NZST or email: info@
kaboodlegroup.com.au.
Clean your cabinets with an all purpose, non-abrasive cleaner with a damp sponge or cloth and
make sure you never use saturated cloth, harsh chemicals or thinner based cleaners as these will
damage the surface of the melamine. Likewise, never use products that will scratch the surface like
steel wool or wire brushes and avoid sharp objects that will scratch, cut or gouge the melamine
surface. If this happens the internal board will be exposed and may swell. Kaboodle cabinets are
water resistant but not water proof so any spills should be attended to immediately.
Handy hint: if the melamine surface of your cabinet is damaged you can try and cover it with a
furniture repair crayon but just remember that this won’t seal the board back to its original finish.
Caring for your kaboodle parts and accessories: Looking after your parts and accessories is really
easy and with the right care and maintenance they will last you for many years. Just follow these
simple steps. Hinges, runners and other parts and accessories should be kept dry at all times. To
keep the mechanisms performing at their best, regularly wipe them with a dry cloth removing any
dust and grime that may build up. In case of spills, clean immediately with a dry cloth. Do not use
harsh abrasives.
Easily attach the wire baskets by inserting the wire pegs,
located at the back (i), at even intervals (left to right
side) and then gently push down to secure into position.
Small baskets are to be used on the door rack.
Ensure baskets are secure and level before loading.
NOTE: Do not overload baskets as this could interfere
with functionality, cause the product to fail or cause
damage to your pantry door. Max weight capacity
is 5kg per large basket and 3kg per small basket.
450mm pantry pullout baskets 6 tier
(i)
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]