Kaboodle W50556 User manual

step 2
Hardware included
C DBA
Tools you will need
To put your under cabinet LED panel together you will need the following tools.
Cordless drill with:
• Number 2 screw tip
• 10mm drill bit Tape
measure
IR Control Switch with cable
*Not included – sold separately
LED Driver and distributor
*Not included – sold separately
Safety
gearPencil
Things you need to know
• When using electrical products, basic safety precautions
should always be followed, including the following:
• Always read the instructions first before installation
• Cut off the power source during the installation
• Not suitable for outdoor use
• Don’t bend the cables
• Never operate if it has a damaged power cord or plug
• Please consider the total wattage of all lights being joined
together and select the LED Driver that is greater than this total,
taking into consideration the following:
• 15w = max load 13.5w
• 30w = max load 27w
• 75w = max load 67.5w
• If you have any questions, contact us on:
Australia: 1800 666 078 Monday to Friday between
8:00am and 6:00pm AEST, New Zealand: 0800 522 663
Monday to Friday between 8:00am and 5:00pm NZST
or email: [e-mail].
bridge connector x 1 extension cable x 1
16mm screws x 2 (400/450 LED Panel)
16mm screws x 3 (600/900 LED Panel)
25mm screws x 2 (400/450 LED Panel)
25mm screws x 3 (600/900 LED Panel)
installation guide
p. 1Ver. 1
W50556
W50557
W50558
W50559
Follow these
instructions to
build and attach
your under cabinet
LED Panels.
under cabinet LED panel

step 2
1.
2.
under cabinet LED panel
Position the LED Panel under a shelf or
overhead cabinet and note the position of
the power cable.
Drill a 10mm hole in the base of the cabinet
(where the power cable is located) to allow
for the power cable to be fed through into
the cabinet above.
Fix the 25mm screws in the rear (thicker)
part of the panel and the 16mm screws in
the front.
LED panel
extension
cable
Connect two Lamps by
Bridge Connector
The Bridge Connector can be used to join two (or more) LED panels
together in a row whilst utilising only 1 power cable.
1. Insert the Bridge connector into the first panel then position the
second panel alongside it.
2. Push the second panel towards the first panel until both panels
are side by side with no gaps between.
3. Fix second panel using included screws.
Note: Maximum length of connected panels must not exceed 3
meters (without IR Control Switch). If using IR Control Switch,
maximum length of connected panels must not exceed 2 meters.
p. 2Ver. 1
W50556
W50557
W50558
W50559
Ø10
!

step 2
under cabinet LED panel
Do not connect more than two Under
Cabinet LED panels to a power supply
if you have used the Bridge Connector.
Only one panel needs to be connected
to power using this method.
Please refer to the below illustrations.
p. 3Ver. 1
W50556
W50557
W50558
W50559
AWM2468 AWG2 4 300V 80°Ê AWM2468 AWG24 3 00 V 80°Ê AWM2468 A WG2 4 3 00V 80°Ê AWM2468 AWG24300V 80°Ê AWM2468 AW G 24 300V 80°Ê AWM2468 AWG243 00 V 80°Ê
Bridge connector
AWM2468 AWG2 4 300V 80°Ê AWM246 8 AWG24300V 80°Ê AWM2468 AWG2 4 300V 80°Ê AWM246 8 AWG24 300V80°Ê AWM2468 AWG2 4 300V 80°Ê AWM246 8 AWG24300V 80°Ê
12VDC
12VDC
12VDC
Bridge connector
AWM2468 AWG2 4 300V8 0°Ê AWM2468 AWG24300V 80°Ê AWM2468 AWG2 4 300V 80°Ê AWM246 8 AWG 2 4 300V 8 0°Ê AWM2468 AWG2 4 300V 80°Ê AWM246 8 AWG2 4 300V8 0°Ê
Bridge connector
12VDC
AWM2468 AWG2 4300V 80°Ê A WM2468 AWG24300V 80°Ê AWM2468 AWG2 4300V 80°Ê A WM2468 AWG24300V 80°Ê AWM2468 AWG2 4 300V 80°Ê AWM24 68 AWG24300V 80°Ê
Bridge connector
12VDC
Bridge connector
Bridge connector
Bridge connector
Bridge connector

under cabinet LED panel
step 2
We offer a dedicated customer service line
for advice or any questions you may have
on kaboodle products.
Call customer service on:
Australia: 1800 666 078 Monday to Friday
between 8.00am and 6.00pm AEST
New Zealand: 0800 522 663 Monday to Friday
between 8.00am and 5.00pm NZST or email:
[e-mail]
Caring for your kaboodle parts and accessories
Looking after your cabinets is really easy and with the right care and maintenance they
will last you for many years. Just follow these simple steps and if you need any more
information you can contact us on 1800 666 078 Monday to Friday between 8:00am
and 6:00pm AEST or email: [e-mail].
Hinges, runners and other parts and accessories should be kept dry at all times.
To keep the mechanisms performing at their best, regularly wipe them with a dry cloth
removing any dust and grime that may build up.
p. 4Ver. 1
W50556
W50557
W50558
W50559
step 1
step 2
step 3
step 4
Next, follow the
instructions to fit
your doors and
panels.
Finish off your
Kaboodle Kitchen
by installing your
benchtop.
You’ve finished
adding your
parts and
accessories.
Your Kaboodle
cabinet is now
complete.
3.
If you are using an IR Control Switch with
the 15W or 30W Driver & Distributor, the
IR Control Switch can be connected in
between the Driver, and the Distributor.
1. Separate the connector between the
Voltage LED Driver and the distributor
2. Connect IR Control Switch to
connectors at end of the Driver and
the Distributor.
3. Insert extension cable from LED panel
into Distributor
4. Connect Driver to power source
If you are using an IR Control Switch with
the 75W Driver, the Distributor cannot be
separated.
1. Connect IR Control Switch directly to
the Distributor.
2. Insert extension cable from LED panel
into end of IR Control Switch
3. Connect Driver to power source.
11
11
22
22
33
33
Voltage LED
Driver
Voltage LED
Driver
IR Control Switch
with Cable
Distributor
Distributor
4