Kaco blueplanet 29.0 TL3 Series User manual

Operating Instructions
English translation
of German original
blueplanet
. TL S/M/XL
These instructions form part of the product and must be observed. They must also be stored in a place which is freely
accessible at all times.

The copyright for these operating instructions is held solely by KACO new energy GmbH.

Operating Instructions KACO blueplanet .TL Page 
EN
Operating Instructions
Contents
 General information .................................
. About this document............................................
. Layout of Instructions...........................................
. Target group.............................................................
 Safety ......................................................... 
. Proper use.................................................................
. Protection features ................................................
. Identication............................................................
. More information ................................................... 
 Description ................................................ 
. Mode of Operation ................................................ 
. Diagram .................................................................... 
 Technical Data ......................................... 
. Electrical data ........................................................ 
. Mechanical data.....................................................
. Environmental conditions ................................. 
 Transportation and Delivery...................
. Scope of delivery...................................................
. Transportation........................................................
 Mounting ..................................................
. Unpacking............................................................... 
. Installing the wall bracket................................. 
. Installing the unit................................................. 
 Electrical connection ...............................
. Switching o the unit..........................................
. Preparing the AC connection...........................
. Connection within the distribution system 
. Connection to the power grid ........................
. Preparing the DC connection ..........................
. Connecting the PV generator..........................
. Grounding the housing .....................................
. AC and DC overvoltage protection upgrade
. Connecting the interfaces.................................
. Sealing the connection area ............................
. Switching on the device....................................
 Conguration and Operation..................
. Controls.....................................................................
. Initial start-up ........................................................
. Menu structure......................................................
. Inverter monitoring............................................ 
. Performing the software update................... 
 Maintenance/Troubleshooting ..............
. Visual inspection.................................................. 
. Cleaning the housing ........................................ 
. Cleaning the heat sink....................................... 
. Replacing the fan .................................................
. Replacing the string fuse (XL version) .......... 
. Shutting down for maintenance and
troubleshooting.................................................... 
. Checking or replacing surge protection
device .......................................................................
. Disconnecting connections..............................
. Faults.........................................................................
. “Fault”messages on the display/LED............
 Service......................................................
 Shutdown/Disassembly.......................... 
. Switching o the unit......................................... 
. Uninstalling the device ...................................... 
. Disassembling the unit ......................................
. Packaging the unit...............................................
. Storing the unit.....................................................
 Disposal ................................................... 
 Appendix ................................................. 
. EU Declaration of Conformity..........................

General information
Page  Operating Instructions KACO blueplanet .TL
ENEN  General information
. About this document
WARNING
Improper handling of the device can be hazardous!
›You must read and understand the operating instructions so that you can
install and use the device safely!
.. Other applicable documents
During installation, observe all assembly and installation instructions for components and other parts of the system.
These instructions also apply to the equipment, related components and other parts of the system. Some of the
documents which are required for the registration and approval of your photovoltaic (PV) system are included with
the operating instructions.
.. Storing the documents
These instructions and other documents must be stored near the system and be available at all times. The content
of these instructions is revised on a regular basis and updated if necessary. You can download the current version of
the operating instructions at www.kaco-newenergy.com/us.
.. English translation of German original
These operating instructions have been produced in several languages. The German-language version of the
operating instructions is the original version. All other language versions are translations of the original operating
instructions.
. Layout of Instructions
.. Symbols used
General hazard Risk of re or explosion!
Electrical voltage! Risk of burns
Authorised electrician Only authorised electricians are permitted to carry out tasks indicated with this
symbol!
.. Safety warnings symbols guide
DANGER
High risk
Failure to observe this warning will lead directly to serious bodily injury or death.
WARNING
Potential risk
Failure to observe this warning may lead to serious bodily injury or death.
CAUTION
Low-risk hazard
Failure to observe this warning will lead to minor or moderate bodily injury.

Safety
Operating Instructions KACO blueplanet .TL Page 
EN
CAUTION
Risk of damage to property
Failure to observe this warning will lead to property damage.
.. Additional information symbols
NOTE
Useful information and notes
EN Country-specic function
Functions restricted to one or more countries are labelled with country codes in accordance with
ISO-.
.. Instructions symbols guide
Instructions
ඣPrerequisite(s) before carrying out the following step(s) (optional)
. Carry out step.
. (Additional steps, if applicable)
» Result of the step(s) (optional)
. Target group
All activities described in the document may only be carried out by specially trained personnel with the following
qualications:
• Knowledge about how an inverter functions and operates
• Training in the handling of hazards and risks during the installation and operation of electrical devices and sys-
tems
• Education concerning the installation and start-up of electrical units and systems
• Knowledge of applicable standards and directives
• Knowledge and adherence to this document with all safety notices.
 Safety
DANGER
Lethal voltages are still present in the terminals and cables of the inverter even after the
inverter has been switched o and disconnected!
Severe injuries or death will occur when touching the cables and terminals in the inverter.
›Only appropriately qualied and authorised electricians may open, install or maintain the inverter.
›Keep the inverter closed when the unit is in operation.
›Do not touch the cables or terminals when switching the unit on and o.
›Do not make any modications to the inverter.
The electrician is responsible for observing all existing standards and regulations.
• Be sure to observe IEC --: “Requirements for special installations or locations – solar photovoltaic
(PV) power supply systems”in particular and all applicable regulations and specications.
• Ensure operational safety by providing proper grounding, conductor dimensioning and appropriate protection
against short circuiting.
• Observe all safety instructions on the inverter and in these operating instructions.

Safety
Page  Operating Instructions KACO blueplanet .TL
ENEN • Switch o all voltage sources and secure them against being inadvertently switched back on before performing
visual inspections and maintenance.
• When taking measurements while the inverter is live:
–Do not touch the electrical connections
–Remove all jewellery from wrists and ngers.
–Ensure that the testing equipment is in safe operating condition.
• Modications to the surroundings of the inverter must comply with the applicable national and local standards.
• When working on the PV generator, it is also necessary to switch o the DC voltage with the DC isolator switch in
addition to disconnecting the PV generator from the grid.
. Proper use
The inverter converts the DC voltage generated by the PV modules into AC voltage and feeds it into the grid. The
inverter is built according to the latest technological standards and safety regulations. Nevertheless, improper use
may cause lethal hazards for the operator or third parties, or may result
in damage to the device and other property.
Operate the inverter only with a permanent connection to the public power grid.
Any other or additional use is not considered proper or intended use and can lead to an annulment of the product
guarantee. This includes:
• Mobile use
• Use in rooms where there is a risk of explosion
• Use of the inverter in direct sunlight, rain or a storm or other harsh environmental conditions
• Use in an outdoor area that does not meet the environmental conditions set down in the Technical Data, section
.
• Operation outside the specications intended by the manufacturer
• Overvoltage of over V on the DC connection.
• Modifying the unit
• Standalone mode
. Protection features
The following monitoring and protection functions are built-in:
• Overvoltage conductors/varistors to protect the power semiconductors from high-energy transients on the grid
and generator side
• Temperature monitoring of the heat sink / temperature monitoring of the interior
• EMC lters to protect the inverter from high-frequency grid interference
• Grid-side grounded varistors to protect the inverter against burst and surge pulses
• Standalone grid detection according to the current standards.
. Identication
Identifying the unit
ඣYou will nd the name plate with product-specic data for service and
other requirements specic to installation on the right side panel of
the inverter. This data includes:
• Product name
• Part no.
• Serial number
• Date of manufacture
• Technical Data
• Disposal information
• Certication marking, CE marking.
KACO new energy
Carl-Zeiss-Straße 1
74172 Neckarsulm
Made in Germany
KACO BLUEPLANET 29.0 TL3 M1 WM OD II4X
Part number 1001664
Serial number 00000000000123456 Year Q3 / 17
Input Vmax PV / lsc PV (max) / Inom PV 1100V/190A/85A
V-MPP at Pnom / V- range 360 V - 900 V
Output
Nominal voltage
120 V / 208 V (3/N/PE)
127 V / 220 V (3/N/PE)
138 V / 240 V (3/N/PE)
Voltage range continuous operation 166 V - 346 (Ph-Ph)
Current (maximum continuous) 3x76,5A
Frequency range 42 Hz - 68 Hz
Output
Power
Rated power / maximum power 27500 VA @ 120V / 30100 VA
Rated power / maximum power 29000 VA @ 127V / 30100 VA
Rated power / maximum power 29000 VA @ 138V / 30100 VA
Reactive power cos phi 0-100% Snom 1-0,3 ind/cap
Environ-
ment Temperature range - 20°C ... + 60°C
Protection class / Ingress protection I/IP65
ARC fault circuit protection
none
Interface protection according to country
specic requirements, details see manual
No galvanic separation / UTILITY-INTERCONNECTED
Figure : Type plate XL version

Description
Operating Instructions KACO blueplanet .TL Page 
EN
. More information
NOTE
The EU Declaration of Conformity can be found in the appendix.
For information on grid coupling, grid protection and safety parameters along with more detailed
instructions see our website at http://www.kaco-newenergy.com/us.
 Description
. Mode of Operation
The inverter converts the DC voltage generated by the PV modules into AC voltage and feeds it into the grid. The
starting procedure begins when there is sucient sunlight and a specic minimum voltage is present in the inverter.
The feed-in process begins once the PV generator has passed the insulation test and the grid parameters are within
the requirements imposed by the grid operator for a specic monitoring time. If, as it gets dark, the voltage drops
below the minimum voltage value, feed-in operation ends and the inverter switches o.
. Diagram
2
3
5
4
6
1
2
3
5
4
6
1
Figure : Inverter diagram - XL version Figure : Inverter diagram - M version
Key
1 Housing 4 Wall bracket
2 Door with control panel 5 DC connection / tting (M version)
3 DC isolator switch (not present in S version) 6 Cable feed-through for AC connection
.. Mechanical components
DC isolator switch (not present in S version)
The DC isolator switch is located on the front of the inverter housing. The DC isolator switch is used to disconnect
the inverter from the PV generator in order to carry out service activities.

Description
Page  Operating Instructions KACO blueplanet .TL
ENEN ON
OFF
Figure : DC isolator switch
Disconnecting the inverter from the PV generator
"Switch the DC isolator switch from  (ON) to  (OFF).
Connecting the inverter to the PV generator
"Switch the DC isolator switch from  (OFF) to  (ON).
.. Electrical functions
A potential-free relay contact is integrated in the inverter. Use this contact for one of the following functions:
Fault signal relay
The potential-free relay contact closes as soon as there is a fault during operation. You use this function, for example,
to signal a fault visually or acoustically.
Priwatt
The energy that is provided by the PV system can be put to use directly by the appliances that are connected in your
home.
The potential-free contact can switch larger appliances (e.g. air conditioning units) on and o with the Priwatt func-
tion activated. This requires an external power supply and an external load relay.
When the function is active, either the remaining runtime (in hours and minutes) or the shutdown threshold (in kW)
is displayed on the start screen depending on the operating mode selected. The Priwatt function is not active in the
factory default setting. The option can be congured in the Settings menu.
.. Interfaces
You congure the interfaces and the web server in the Settings menu.
The inverter has the following interfaces for communication and remote monitoring:
Ethernet interface
Monitoring can occur directly on the unit using the integrated Ethernet interface. A local web server is installed in
the unit for this purpose.
For the monitoring of a system consisting of multiple inverters, we recommend the utilization of the Powador-web
portal on our homepage.
RS interface
In addition to the monitoring via the Ethernet interface, the monitoring can be executed via the RS interface.
USB interface
The USB connection of the inverter is a type A socket. It is located on the connection board in the door. The USB con-
nection is specied to draw mA of power. Use the USB interface to read out stored operating data and to load
software updates using a FAT-formatted USB stick.
“Inverter O” input
If Powador protect is installed as a central grid and system protection, the fail-safe disconnection of suitable Pow-
ador or blueplanet inverters from the public grid can be initiated by a digital signal instead of external interface
switches. This requires the inverters in the photovoltaic system to be connected to the Powador-protect.
If a Powador-protect is used for fast shutdown, it must be used as grid protection. The RS interface is not
required for this.
For information on the installation and use see this manual, the Powador protect operating instructions and the
instructions for use of the Powador protect on the KACO new energy website.

Description
Operating Instructions KACO blueplanet .TL Page 
EN
.. Inverter as part of a PV system
KWhKWh
PV generator PV generator
Inverter with
DC isolator switch*)
and circuit-breaker
Inverter with
DC isolator switch*)
and circuit-breaker
Line protection Line protection
Load
Feed-in meterReference
counter
Selective main
switch
Grid connection point
Selective
main switch
Figure : Circuit diagram of a system with two inverters
Key Denition / Information about the connection
PV generator The PV generator, i.e. the PV modules, converts the radiant energy of sunlight into elec-
trical energy.
Inverter with:
- DC connection
The PV generator is connected directly to the inverter's DC connection. Up to 10 strings
can be connected to the DC connection in the XL device version.
- DC isolator switch Use the DC isolator switch to disconnect the inverter from the PV generator. Note:
*Device version S: An external DC isolator switch is required outside the inverter.
DANGER
Lethal voltages are still present in the terminals and cables of the inverter even after the
inverter has been switched o and disconnected!
Disconnect the DC side depending on the device version:
. XL device version: Switch o the DC supply using the DC isolator switch.
M device version: Switch o DC power supply externally via the combiner box (not supplied) and
using the DC isolator switch.
. Check that there is no current in any of the DC cables using a clip-on ammeter.
. Only open the fuse holder once you have established that there is no current in the DC cables.
. XL device version: Disconnect all DC connections one by one.
M device version: Detach DC connection in the device (see section .. on page ).
Circuit breaker A circuit breaker is an overcurrent protection device.
Feed-in meter The feed-in meter is to be specied and installed by the power supply company. Some
power supply companies also allow the installation of your own calibrated meters.
Selective
main switch
The selective main switch is to be specied by the power supply
company.

Technical Data
Page  Operating Instructions KACO blueplanet .TL
ENEN  Technical Data
. Electrical data
Input levels
Recommended power range of the generator [kW] 29.0 - 40.0
MPP@Pnom from [V] to [V]* 360 - 900
Operating range from [V] to [V] 360*... 1,050
Nominal voltage/ Starting voltage [V] 410 / 460
No-load voltage (UOC max ) [V] 1,100
Max. input current [A] 85
Max. power of the MPP tracker [W] 29,900
Number of DC connections 1 (S/M version) / 6 (XL version)
Number of MPP controls 1
max. short-circuit current (ISC max ) [A] 190
max. input source feedback current [A] 0
Polarity safeguard no
Output levels
Rated power [VA] 29,000
Grid voltage [V] 138/240 (3 / N / PE);
127/220; 120/208 (3 / N / PE)
Voltage range [V] 95 -200 (Ph-N) / 166-346 (Ph-Ph)
Rated current [A] 3x 69.8@240 V; 3x 76.1 @220 V; 3x 76.5 @208 V
Max. continuous current [A] 76.5
Nominal frequency / frequency range [Hz] 50/60 / 42 - 68
cos phi 0.30 inductive ... 0.30 capacitive
Number of feed-in phases 3
Distortion factor (THD) [%] < 1.6
General electrical data
Max. eciency [%] 97.0
European eciency [%] 96.5
Power consumption: standby [W] 2.5
Feed-in starts at [W] 120
Circuit design Transformerless
Grid monitoring Country-specic
Table 1: Electrical data

Technical Data
Operating Instructions KACO blueplanet .TL Page 
EN
. Mechanical data
Display Graphical LCD, 3 LEDs
Controls 4-way button, 2 buttons
Interfaces 2x Ethernet, USB, RS485
optional via additional module: 4-DI
Fault signal relay Potential-free NO contact, max. 30V/1A DC
AC connection (version, type, feed-through cross
section, cable cross section)
S, M and XL; connection via screw terminals,
95 mm², cable connection via M63 cable tting
DC connection (version, type, feed-through cross
section, cable cross section)
S, M: Connection with cable lug, 95 mm², cable connection
via cable tting M32
XL: Connection via 6x DC plug connectors, 2.5 - 6 mm², -
Connection interfaces (type, feed-through cross
section)
Network: Ethernet cable, cable connection via cable tting
M25, standard
RS485: 2-wire, cable connection via cable tting M16 max.
1.5 mm
Temperature monitoring Yes
Cooling (free convection (K)/fan (L)) L
Degree of contamination PD 2
Noise emission [dB(A)] 61
DC isolator switch Built-in
Housing Aluminium
H x W x D [mm] 760 x 500 x 425
Total weight [kg] 73(XL version) 71(M version) 69 (S-Version)
CE conformity Yes
Table 2: Mechanical data
* With a supply voltage of 240 V or higher the lower MPP voltage is increasing accordingly.
. Environmental conditions
Product name: KACO blueplanet
29 TL3 M1 WM OD xxxx
Last 4 characters of product name/item number II4S 1001724 /II4M 1001663 / II4X 1001664
Distance from coast > 2000 m
Ambient temperature range [°C] -20 ... +60 Power reduction above +50
Humidity range (non-condensing) [%] 100
Maximum installation elevation (m above mean
sea level) 3000 (Power reduction above 2000)
Protection rating according to EN 60529 IP65 (tested according to DIN EN 60068-2-52)
Table 3: Environmental conditions
* For installation in aggressive environmental conditions (e.g. possibility of corrosion), you must contact the KACO
Sales team ([e-mail]).

Transportation and Delivery
Page  Operating Instructions KACO blueplanet .TL
ENEN  Transportation and Delivery
Every inverter leaves our factory in proper electrical and mechanical condition. Special packaging ensures that the
units are transported safely. The shipping company is responsible for any transport damage that occurs.
. Scope of delivery
•  inverter
•  wall bracket
•  installation kit
•  insulating tube (for interface cables)
•  set of DC plug connectors (only for the XL device version)
•  documentation set (EN, ES)
Checking your delivery
. Inspect your inverter thoroughly.
. Immediately notify the shipping company in case of the following:
–Damage to the packaging that indicates that the inverter may have been damaged
–Obvious damage to the inverter.
. Send a damage report to the shipping company immediately.
The damage report must be received by the shipping company in writing within six days following receipt of the
device. We will be glad to help you if necessary.
. Transportation
CAUTION
Impact hazard, risk of breakage to the inverter
›Pack the inverter securely for transport.
›Carefully transport the inverter using the carrying handles of the packaging box.
›Do not subject the inverter to shocks.
For safe transportation of the inverter, use the holding openings in the carton.
Packaging
(folding cartons)
(H x W x D (mm))
Total weight [kg]
 x  x 
 (XL version)
 (M version)
 (S version)
Figure : Transportation of the inverter Table 4: Dimensions and weight

Mounting
Operating Instructions KACO blueplanet .TL Page 
EN
 Mounting
DANGER
Risk of fatal injury due to re or explosions!
Fire caused by ammable or explosive materials in the vicinity of the inverter can lead to serious
injuries.
›Do not mount the inverter in an area at risk of explosion or in the vicinity of highly ammable mate-
rials.
Installation location
• As dry as possible, climate-controlled, with the waste heat dissipated away from the inverter
• Air circulation should not be blocked
• When installing the unit in a control cabinet, provide forced ventilation so that the heat is suciently dissipated
• Access to the inverter must also be possible without additional tools
• For outdoor installation, t the inverters in such a way that they are protected against direct sunlight, moisture
and dust penetration
• For easy operation, ensure during installation that the display is slightly below eye level.
Wall surface
• Must have adequate load-bearing capacity
• Must be accessible for installation and maintenance
• Must be made of heat-resistant material (up to °C)
• Must be ame resistant
• Minimum clearances to be observed during assembly: see Figure  on page .
NOTE
Access by maintenance personnel for service
Any additional costs arising from unfavourable structural or mounting conditions will be billed to
the customer.
CAUTION
Property damage due to gases that have an abrasive eect on surfaces when they come into
contact with ambient humidity caused by weather conditions.
The inverter housing can be severely damaged by gases (ammonia, sulphur, etc.) if it comes
into contact with ambient humidity caused by weather conditions.
If the inverter is exposed to gases, it must be mounted so that it can be seen at all times.
›Perform regular visual inspections.
›Immediately remove any moisture from the housing.
›Take care to ensure sucient ventilation of the inverter.
›Immediately remove dirt, especially on vents.
›Failure to observe these warnings may lead to inverter damage which is not covered by the KACO
new energy GmbH manufacturer warranty.

Mounting
Page  Operating Instructions KACO blueplanet .TL
ENEN
<20°
Figure : Instructions for wall mounting Figure : Inverter for outdoor installation
CAUTION
Use suitable mounting parts.
›Use mounting material suitable for the subsurface or the mounting material included in the deliv-
ery.
›Mount the inverter upright on a vertical wall only.
›For a free-standing mounting an incline of ° is permissible.
›For upright installation outdoors: Weather-proof base required.
. Unpacking
DETAIL Z4:1
Z
1
2
3
4
6
5
Figure : Opening the packaging Figure : Raise the device
Key
1 Cover 4 Base
2 Side section - upper 5 Side section - lower
3 Clamp (4x) 6 Cardboard box with wall holder and mounting kit

Mounting
Operating Instructions KACO blueplanet .TL Page 
EN
Authorised electrician
CAUTION
Risk of injury caused by excessive physical strain.
Lifting the device for transportation or to change location can lead to injuries (e.g. back injuries).
› The unit should only be lifted using the openings provided or a transportation device.
› The unit must be transported and installed by at least  persons.
Unpacking the unit
ඣThe unit is transported to the installation location.
. Remove the plastic band from the pallet and packaging and Pull the clamp o the packaging.
. Lift up the cover and set the cardboard box with wall holder and accessories aside.
. Set the unit with base and side sections upright.
. Remove the upper side section and base from the unit.
» If the unit is in the correct installation position: Proceed with the installation of the wall holder.
. Installing the wall bracket
400mm*
500 mm 300 mm
550mm
400mm*
111mm






1150
600
250
400
**
**


Figure : Minimum clearances/mounting Figure : Position of wall holder/ suspension
Key
1 Wall bracket 5 Screw for securing purposes (1x)
2 Fixings for mounting 6 Bracket to prevent unit displacement
3 Lock washer 7 Marking as installation aid
4 Screws for mounting (5x) 8 Seating recess
*
**
Recommended clearance: 400 mm / minimum clearance: 120 mm
recommended clearance: 550 mm / minimum clearance: 370 mm
Installing the wall bracket
ඣCardboard box with wall holder and mounting kit removed from packaging and opened.
. Mark the suspension position with a line on the wall surface corresponding to the position of the wall holder
(Figure ) .

Mounting
Page  Operating Instructions KACO blueplanet .TL
ENEN
Authorised electrician
. Mark the positions of the drill holes using the slots in the wall bracket.
NOTE: The minimum clearances between two inverters, or the inverter and the ceiling/oor have already
been taken into account in the diagram (Figure  on page ).
. Fix wall mount to the wall with the supplied mounting xtures in the mounting kit.
NOTE: Make sure that the wall bracket is aligned correctly.
» Proceed with the installation of the unit.
CAUTION
Power reduction due to heat accumulation.
In the event of insucient ventilation and the resulting heat build-up, the unit will go into power
regulation mode.
›Observe minimum clearances and provide for sucient heat dissipation.
›All objects on the inverter housing must be removed during operation.
›Ensure that foreign bodies do not get in (cable residue, cable ties) via the heat sink guard plate.
Otherwise cleaning must take place before initial operation.
. Installing the unit
WARNING
Risk of injury from improper lifting and transport.
If the unit is lifted improperly, it can tilt and result in a fall.
›Always lift the unit vertically using the openings provided.
›Use a climbing aid for the chosen installation height.
›Wear protective gloves and safety shoes when lifting and lowering the unit.
›Do not attach the unit to the web of the upper side of the housing.
1
1
2


N
O
4
5
Figure : Lift the unit using the opening Figure : Insertion aid in wall holder
Key
1 Opening 4 Marking for insertion into wall holder
2 Centre of gravity 5 Outer contour of wall holder
3 Warning sign (attachment prohibited)

Electrical connection
Operating Instructions KACO blueplanet .TL Page 
EN
Authorised electrician
Lifting and installing the unit
ඣWall holder mounted.
. Use the lateral openings for lifting or
insert the transport device into the lateral slots and lift the unit at the designated positions (see Figure  on
page ).
. Hang the inverter on the wall holder using the suspension brackets on the back of the housing.
NOTE: Keep in mind that the lower marking on the housing must protrude over the upper outer contour of the
wall holder. (See Figure  on page ). Ensure that the upper marking is ush with the upper edge of the outer
contour when lowering the unit. The outer contour of the wall holder must be ush with the outer contour of the
housing.
. Insert the provided screw into the bracket on the wall holder and fasten the inverter to secure against displace-
ment.
Alternatively: At this point, the screw mentioned at step  can be replaced by a special screw as anti-theft protec-
tion.
» Installation of the inverter is complete.
Proceed with the electrical installation.
 Electrical connection
DANGER
Lethal voltages are still present in the terminals and cables of the inverter even after the
inverter has been switched o and disconnected!
Severe injuries or death will occur when touching the cables and terminals in the inverter.
Only appropriately qualied and authorised electricians may open and install the inverter.
The inverter must be mounted in a xed position before being connected electrically.
›Comply with all safety regulations and current technical connection specications of the responsi-
ble power supply company.
›Switch o the grid voltage by turning o the external circuit breakers.
›Check that the AC and DC cables are completely free of current using a clip-on ammeter.
›Reduce any DC voltage that is present by covering the module surface.
›Connect the inverter only after the aforementioned steps have been taken.
. Switching o the unit
Switching o the unit
Note: S version: The device is shut down externally at the combiner
box.
. Switch the DC isolator switch from  (ON) to  (OFF).
. Press in the safety catch () from behind.
. Attach the hanging lock () to the safety catch.
DANGER
A measurement in a live state may be required for tests.
Only appropriately qualied and authorised electricians may
open the inverter.
›Observe all safety regulations against harmless contact
with live materials.
N
O
I
O
O
F
F
O
O
F
F
N
O
I
N
O
I
O
O
F
F
N
O
I
O
O
F
F
O
O
F
F
I
O
N
Ø5...Ø10mm
N
1
2
Figure : Lock DC isolator switch to
prevent reconnection

Electrical connection
Page  Operating Instructions KACO blueplanet .TL
ENEN
Authorised electrician
. Preparing the AC connection
.. Opening the unit
Opening the housing door
ඣUnit switched o and secured against restart.
ඣWipe o any moisture on the housing door frame to nullify any poten-
tial liability this could cause.
. Open the housing door by unlocking the upper and lower lock with
the double-bit key provided.
. Open the housing door carefully.
» Proceed to lock the housing door in place.
Close
Open
Figure : Opening the housing door
Locking the housing door in place
ඣHousing door opened.
. Swing the latch lever into the slot.
. Secure the lever so the door does not swing open unexpectedly.
» Survey the connection area, observe the cable requirements and pro-
ceed to connect up the unit.

Figure : Lock the housing door in place
Key
 Housing door
 Latch lever
.. Surveying the connection area
The connection for the AC supply is located inside the housing. The DC input source is connected either inside or
outside the housing depending on the device version (S, M or XL).
PV-
PV+
1
2
5
1
3
4
5
Figure : Connection area: blueplanet . TL M Figure : Connection area: blueplanet . TL XL
Key
1 DC isolator switch  Cable tting (M) for AC connection
2 Cable tting for DC connection (M version) 5 Earthing bolt
3 Connector for DC connection (XL version)

Electrical connection
Operating Instructions KACO blueplanet .TL Page 
EN
Authorised electrician
.. Cable and fuse requirements
AC connection DC connection (M) DC connection (XL)
Max. cable cross-section
without wire sleeves
95 mm² (AL or CU) 95 mm² (max. 120 mm²) - Use an AL-CU
cable lug for an aluminium cable.
2.5-6 mm² (10x DC plug
connectors)
Max. conductor
cross-section
95 mm² with wire
sleeves
95 mm² (max. 120 mm²) screw M8 - ring
cable lug on M8/Ø 9mm²
-
Length of insulation to
be stripped o
25 mm depending on the cable lug used
Tightening torque 10 Nm 15-22 Nm - (DC plug connector)
Recommended cable
type
PV1-F or UL-certied solar cables (ZKLA), AWG 10–14
Table 5: Recommended cable cross-sections and tightening torques
The unit versions M and XL also dier in the following ways:
S, M XL
DC overvoltage protection Base Base + overvoltage conductor
(SPD), type I + II
AC overvoltage protection Base Base
Overvoltage conductor (SPD) Can be retrotted on the DC and AC
side
DC side built-in, can be retrotted
on the AC side
String fuses To be provided externally on-site 15A fuses installed internally
Combiner box To be provided externally on-site Installed internally
Protection class 1
Overvoltage category III
Recommended conductor cross-sections and fuse protection of NYM cables for xed wiring according to VDE
 part 
For cable lengths up to m, use the named conductor cross-sections. Longer cable lengths require larger conduc-
tor cross-sections.
Device version: Conductor cross-sec-
tion
Fuse protection: gL safety fuses
blueplanet 29.0 TL3 S; M
blueplanet 29.0 TL3 XL
min. 25 mm²
min. 25 mm²
min. 100 A for 25 mm² conductor cross-section
max. 125 A for 35 mm² conductor cross-section
Table 6: Recommended conductor cross-sections and fuse protection of NYM cables
. Connection within the distribution system
NOTE
KACO new energy assumes no liability for damages and consequential damages arising from other
connections in the distribution system.
L2
L1
L3
GND/PE*
L3
L1
L2
220V
220V
220V
N
127V
127V
127V
PEN/N
=
~
*) PE earthing in accordance with
earthing system
(see section .: -core connection)
Figure : Example with /V Y (star) connection with earthed neutral point

Electrical connection
Page  Operating Instructions KACO blueplanet .TL
ENEN
Authorised electrician
. Connection to the power grid
The power connection cables are connected to the AC terminals on the left of the connection area (see Figure  and
Figure ).
Making the grid connection (TN-S system, TN-C-S system, TT system)
ඣUse cables with  wires (L: black, L: red, L: blue, N: white, PE: green/
yellow).
ඣCheck the grid voltage and compare with“VAC nom”on the name
plate.
. Loosen cable tting for AC connection.
. Remove the outer cladding of the AC cables.
. Insert the AC cables through the cable tting into the connection area.
. Strip the insulation from the AC cables.
» Making the grid connection.
AC side
DC-side
Figure : Connection terminals for M
version
PV-
PV+
14
PV-
PV+
4
13
2
5
Figure : blueplanet . TL - S ver-
sion
Figure : blueplanet . TL -M
version
Key
1 AC connection terminals 4 DC connection with protection against contact
2 Base AC overvoltage protection 5 Base DC overvoltage protection
3 DC isolator switch
Making the grid connection (TN-C system)
ඣUse cables with  wires (L: black, L: red, L: blue, PEN: green/yellow).
. Check the grid voltage and compare with“VAC nom”on the name
plate.
. Loosen cable tting for AC connection.
. Remove the outer cladding of the AC cables.
. Insert the AC cables through the cable tting into the connection area.
. Strip the insulation from the AC cables.
» Making the grid connection.
AC side
DC-side
Figure : Connection terminals
XL version