Kaco blueplanet 5.0 TL3 User manual

These instructions form part of the product and must be observed. They must also be stored in a place which is freely
accessible at all times.
Operating Instructions
English translation of
German original
blueplanet
5.0 TL3 | 6.5 TL3
7.5 TL3 | 8.6 TL3
9.0 TL3 | 10.0 TL3

The copyright for these operating instructions is held solely by KACO new energy GmbH.

EN
KACO Operating Instructions blueplanet . TL - . TL Page 
Operating Instructions
Contents
 General information .................................
. About this document............................................
. Layout of Instructions...........................................
. Target group.............................................................
 Safety ......................................................... 
. Proper use.................................................................
. Protection features ................................................
. More information...................................................
 Description ................................................ 
. Mode of Operation ................................................ 
. Diagram .................................................................... 
 Technical Data ......................................... 
. Electrical data ........................................................ 
. Mechanical data.....................................................
. Identication...........................................................
 Transportation and Delivery...................
. Scope of delivery...................................................
. Transportation........................................................
 Mounting ..................................................
. Unpacking............................................................... 
. Installing the wall holder................................... 
. Installing the unit..................................................
 Electrical connection .............................. 
. Preparing the AC connection...........................
. Connection to the power grid.........................
. Preparing the DC connection ...........................
. Connecting the PV generator..........................
. Grounding the housing .....................................
. Connecting the interfaces.................................
. Sealing the connection area ............................
. Switching on the device ....................................
 Conguration and Operation................. 
. Controls....................................................................
. Initial start-up ........................................................
. Menu structure......................................................
. Monitor inverter....................................................
. Performing the software update................... 
 Maintenance/Troubleshooting .............. 
. Visual inspection...................................................
. Cleaning the housing .........................................
. Replacing or cleaning the fans........................
. Shutting down for maintenance and
troubleshooting................................................... 
. Disconnecting connections..............................
. Faults........................................................................ 
. "Fault" messages on the display/LED............
 Service...................................................... 
 Shutdown/Disassembly.......................... 
. Switching o the unit.........................................
. Uninstalling the device ......................................
. Disassembling the unit ......................................
. Packaging the unit...............................................
. Storing the unit.....................................................
 Disposal ...................................................
 Appendix ................................................. 
. EU Declaration of Conformity..........................

ENEN
General information
Page  KACO Operating Instructions blueplanet . TL - . TL
 General information
. About this document
WARNING
Improper handling of the device can be hazardous!
›You must read and understand the operating instructions so that you can
install and use the device safely!
.. Other applicable documents
During installation, observe all assembly and installation instructions for components and other parts of the system.
These instructions also apply to the equipment, related components and other parts of the system. Some of the
documents which are required for the registration and approval of your photovoltaic (PV) system are included with
the operating instructions.
.. Storing the documents
These instructions and other documents must be stored near the system and be available at all times. The content
of these instructions is revised on a regular basis and updated if necessary. You can download the current version of
the operating instructions at www.kaco-newenergy.com.
.. English translation of German original
These operating instructions have been produced in several languages. The German-language version of the
operating instructions is the original version. All other language versions are translations of the original operating
instructions.
. Layout of Instructions
.. Symbols used
General hazard Risk of re or explosion
High voltage Risk of burns
Authorised electrician Only authorised electricians are permitted to carry out tasks indicated with this
symbol!
.. Safety warnings symbols guide
DANGER
High risk
Failure to observe this warning will lead directly to serious bodily injury or death.
WARNING
Potential risk
Failure to observe this warning may lead to serious bodily injury or death.
CAUTION
Low-risk hazard
Failure to observe this warning will lead to minor or moderate bodily injury.

EN
Safety
KACO Operating Instructions blueplanet . TL - . TL Page 
CAUTION
Risk of damage to property
Failure to observe this warning will lead to property damage.
.. Additional information symbols
NOTE
Useful information and notes
EN Country-specic function
Functions restricted to one or more countries are labelled with country codes in accordance with
ISO-.
.. Instructions symbols guide
Instructions
ඣPrerequisite(s) before carrying out the following step(s) (optional)
. Carry out step.
. (Additional steps, if applicable)
» Result of the step(s) (optional)
. Target group
All activities described in the document may only be carried out by specially trained personnel with the following
qualications:
• Knowledge about how an inverter functions and operates
• Training in the handling of hazards and risks during the installation and operation of electrical devices and sys-
tems
• Education concerning the installation and startup of electrical units and systems
• Knowledge of applicable standards and directives
• Knowledge and adherence to this document with all safety notices.
 Safety
DANGER
Lethal voltages are still present in the terminals and cables of the inverter even after the
inverter has been switched o and disconnected.
Severe injuries or death will occur when touching the cables and terminals in the inverter.
›Only appropriately qualied and authorised electricians may open, install or maintain the inverter.
›Keep the inverter closed when the unit is in operation.
›Do not touch the cables or terminals when switching the unit on and o.
›Do not make any modications to the inverter.
The electrician is responsible for observing all existing standards and regulations.
• In particular, be sure to observe the standard IEC---: "Requirements for special installations or loca-
tions – solar photovoltaic (PV) power supply systems".
• Ensure operational safety by providing proper grounding, conductor dimensioning and appropriate protection
against short circuiting.

ENEN
Safety
Page  KACO Operating Instructions blueplanet . TL - . TL
• Observe all safety instructions on the inverter and in these operating instructions.
• Switch o all voltage sources and secure them against being inadvertently switched back on before performing
visual inspections and maintenance.
• When taking measurements while the inverter is live:
–Do not touch the electrical connections.
–Remove all jewellery from your wrists and ngers.
–Ensure that the testing equipment is in safe operating condition.
• Stand on an insulated surface when working on the inverter.
• Modications to the surroundings of the inverter must comply with the applicable national and local standards.
• When working on the PV generator, it is also necessary to switch o the DC voltage with the DC isolator switch in
addition to disconnecting the PV generator from the grid.
. Proper use
The inverter converts the DC voltage generated by the PV modules into AC voltage and feeds it into the grid. The
inverter is built according to the latest technological standards and safety regulations. Nevertheless, improper use
may cause lethal hazards for the operator or third parties, or may result in damage to the unit and other property.
Operate the inverter only with a permanent connection to the public power grid.
Any other or additional use of the device shall be regarded as improper. This includes:
• Mobile use
• Use in rooms where there is a risk of explosion
• Use in outdoor areas if the inverter is exposed to direct sunlight, rain or a storm
• Operation outside the specications intended by the manufacturer
• Modifying the device
• Standalone operation.
. Protection features
The following monitoring and protective functions are integrated into KACO inverters:
• Overvoltage conductors/varistors to protect the power semiconductors from high-energy transients on the grid
and generator side
• Temperature monitoring of the heat sink
• EMC lters to protect the inverter from high-frequency grid interference
• Grid-side grounded varistors to protect the inverter against burst and surge pulses
• Islanding detection according to the current standards.
. More information
NOTE
The EU Declaration of Conformity can be found in the appendix. For information on grid coupling,
grid protection and safety parameters along with more detailed instructions see our web site at
http://www.kaco-newenergy.de/.

EN
Description
KACO Operating Instructions blueplanet . TL - . TL Page 
 Description
. Mode of Operation
The inverter converts the DC voltage generated by the PV modules into AC voltage and feeds it into the grid. The
starting procedure begins when there is sucient sunlight and a specic minimum voltage is present in the inverter.
The feed-in process begins once the PV generator has passed the insulation test and the grid parameters are within
the requirements imposed by the grid operator for a specic monitoring time. If, as it gets dark, the voltage drops
below the minimum voltage value, feed-in operation ends and the inverter switches o.
. Diagram
1
2
5
4
3
Figure : Inverter diagram
Key
1 Control panel 4 DC connection (DC connector)
2 Cover for the connection area 5 AC connection (5-pole connecting plug)
3 DC isolator switch
.. Mechanical components
DC isolator switch
The DC isolator switch is located on the underside of the inverter. The DC isolator switch is used to disconnect the
inverter from the PV generator in order to carry out service.
Figure : DC isolator switch
Disconnecting the inverter from the PV generator
"Switch the DC isolator switches from  (ON) to  (OFF).
Connecting the inverter to the PV generator
"Switch the DC isolator switches from  (OFF) to  (ON).
.. Electrical functions
A potential-free relay contact is integrated in the inverter. Use this contact for one of the following functions:
Fault signal relay
The potential-free relay contact closes as soon as there is a fault during operation. You use this function, for example,
to signal a fault visually or acoustically.

ENEN
Description
Page  KACO Operating Instructions blueplanet . TL - . TL
Priwatt
The energy that is provided by the PV system can be put to use directly by the appliances that are connected in your
home.
The potential-free contact can switch larger appliances (e.g. air conditioning units) on and o with the“priwatt”
function activated. This requires an external power supply and an external load relay.
When the function is active, either the remaining runtime (in hours and minutes) or the shutdown threshold (in kW)
is displayed on the start screen depending on the operating mode selected. The“priwatt” function is not active in
the unit’s delivery state. The option can be congured in the Settings menu.
.. Interfaces
You congure the interfaces and the web server in the Settings menu.
The inverter has the following interfaces for communication and remote monitoring:
Ethernet interface
Monitoring can occur directly on the unit using the integrated Ethernet interface. A local web server is installed in
the unit for this purpose.
For the monitoring of a system consisting of multiple inverters, we recommend the utilization of the Powador web
portal on our homepage.
RS interface
In addition to the monitoring via the Ethernet interface, the monitoring can be executed via the RS interface. For
monitoring your PV system using the RS interface, KACO new energy GmbH oers monitoring devices:
Only the RS interface continues to transmit data if the inverter in an inverter group fails.
USB interface
The USB connection of the inverter is a type A socket. It is located on the connection circuit board behind the cover
for the connection area. The USB connection is specied to draw mA of power. Use the USB interface to read out
stored operating data and to load software updates using a FAT-formatted USB stick.
“Inverter O" input
If Powador protect is installed as a central grid and system protection, the fail-safe disconnection of suitable Pow-
ador or blueplanet inverters from the public grid can be initiated by a digital signal instead of tie circuit-breakers.
This requires the inverters in the photovoltaic system to be connected to the Powador protect.
If a Powador-protect is used for fast shutdown, it must be used as grid protection. The RS interface is not
required for this.
For information on the installation and use see this manual, the Powador protect manual and the instructions for
use of the Powador protect on the KACO new energy website.
S interface (optional)
The S interface transmits pulses between a pulsing counter and a tari metering unit. It is a galvanically isolated
transistor output. It is designed according to DIN EN -:- (pulse output devices for electromechanical
and electronic meters).
The S interface pulse rate can be chosen in three unit intervals (, , and , pulses/kWh).
The optional extension module is available from the service department of KACO new energy.

EN
Description
KACO Operating Instructions blueplanet . TL - . TL Page 
.. inverter as part of a PV system
KWhKWh
PV generator PV generator
Inverter with
DC isolator switch
Inverter with
DC isolator switch
Line protection Line protection
Load
Feed-in meterReference
counter
Selective
main switch
Grid connection point
Selective main
switch
Figure : Circuit diagram of a system with two inverters
Key Denition / Information about the connection
PV generator The PV generator, i.e. the PV modules, converts the radiant energy of sunlight into
electrical energy.
Inverter with:
- DC connection The PV generator is connected directly to the inverter's DC connection. Two strings
can be connected to the DC connection.
- DC isolator switch Use the DC isolator switch to disconnect the inverter from all power sources on the
PV generator side.
Circuit breaker A circuit breaker is an overcurrent protection device.
Feed-in meter The feed-in meter is to be specied and installed by the power supply company.
Some power supply companies also allow the installation of your own calibrated
meters.
Selective main switch If you have questions about the selective main switch, contact your power supply
company.

ENEN
Technical Data
Page  KACO Operating Instructions blueplanet . TL - . TL
 Technical Data
. Electrical data
Product name: KACO blueplanet 5.0 TL3 6.5 TL3 7.5 TL3
Input levels
Maximal empfohlene DC Leistung [kW] 6 7,8 9
MPP@Pnom from [V] to [V] 240 ... 800 310 ... 800 350 ... 800
Operating range from [V] to [V] 200 ... 950
Starting voltage [V]* 250
No-load voltage (UOC max ) [V] 1 000 (start to 950)
Max. input current [A] 2 x 11
Max. power per MPP tracker [W] 5 200 6 700 7 700
Number of strings 2
Number of MPP controls 2
max. short-circuit current (ISC max ) [A] 16 (per tracker)
max. input source feedback current 0
Output levels
Rated power [VA] 5 000 6 500 7 500
Grid voltage [V] 400/230 (3/N/PE)
Rated current [A] 3 x 7.25 3 x 9.50 3 x 10.90
Max. rated current [A] 3 x 7.62 3 x 9.98 3 x 11.45
contribution to maximum peak current (îp) [A] 35
Initial short-circuit alternating current (lk” rst
single period eective value) [A]
16.5
Start-up current [A] 1.03
Rated frequency [Hz] 50/60
cos phi 0.30 inductive ...0.30 capacitive
Number of feed-in phases 3
THD [%] 3.85
General electrical data
Eciency [%] 98.3 98.3 98.3
European eciency [%] 97.4 97.6 97.7
Self consumption: night [W] 2
Feed-in starts at [W] 20
Circuit design Transformerless
Grid monitoring Country-specic
Ground fault monitoring Yes
Table 1: Electrical data

EN
Technical Data
KACO Operating Instructions blueplanet . TL - . TL Page 
Product name: KACO blueplanet 8.6 TL3 9.0 TL3 10.0 TL3
Input levels
Maximum recommended DC power [kW] 10,3 10,8 12
MPP@Pnom from [V] to [V] 403 ... 800 420 ... 800 470 ... 800
Operating range from [V] to [V] 200 ... 950
Starting voltage [V]* 250
No-load voltage (UOC max ) [V] 1 000 (start to 950)
Max. input current [A] 2 x 11
Max. power per MPP tracker [W] 8 800 8 800 8 800
Number of strings 2
Number of MPP controls 2
max. short-circuit current (ISC max ) [A] 16 (per tracker)
max. input source feedback current 0
Output levels
Rated power [VA] 8 600 9 000 10 000
Grid voltage [V] 400/230 (3/N/PE)
Rated current [A] 3 x 12.50 3 x 13.00 3 x 14.50
Max. rated current [A] 3 x 13.16 3 x 13.76 3 x 15.26
contribution to maximum peak current (îp) [A] 41 35 41
Initial short-circuit alternating current (lk”
rst single period eective value) [A]
18,9 16.5 18,9
Start-up current [A] 1.03
Rated frequency [Hz] 50/60
cos phi 0.30 inductive ...0.30 capacitive
Number of feed-in phases 3
THD [%] 3.85
General electrical data
Eciency [%] 98.3 98.3 98.3
European eciency [%] 97.9 97.9 97.9
Self consumption: night [W] 2
Feed-in starts at [W] 20
Circuit design Transformerless
Grid monitoring Country-specic
Ground fault monitoring Yes
Table 2: Electrical data

ENEN
Technical Data
Page  KACO Operating Instructions blueplanet . TL - . TL
. Mechanical data
Product name: KACO blueplanet 5.0-10.0 TL3
Display Graphical LCD, 3 LEDs
Controls 4-way button, 2 buttons
Interfaces 2 x Ethernet, USB, RS485, error relay
4 x digital inputs (optional)
Fault signal relay Potential-free NO contact 30 V / 1A
AC connections 5-pole connection plug
DC connections 4 (2 x 2) SUNCLIX connector
Ethernet connection: Cable connection Cable connection via M25 cable tting
Ambient temperature range [°C] -25 ... +60, power derating from +40
Humidity range (non-condensing) [%] 100
Maximum installation elevation [m above sea level] 3000
Temperature monitoring Yes
Cooling (free convection (K)/fan (L)) L
Protection rating according to EN 60529 IP65
Degree of contamination 2
Noise emission [dB(A)] <53
DC isolator switch Built-in
Housing Plastic (ASA/PC), aluminium
H x W x D [mm] approx. 522 x 363 x 246
Total weight [kg] 30
CE conformity Yes
Table 3: Mechanical data
* The DC starting voltage can be set in the menu if needed.
. Identication
Identifying the unit
ඣYou will nd the name plate with product-specic data for service and
other requirements specic to installation on the right side panel of
the inverter. This data includes:
• Product name
• Part no.
• Serial no.
• Date of manufacture
• Technical Data
• Disposal information
• Certication marking, CE marking.
KACO new energy
Carl-Zeiss-Straße 1
74172 Neckarsulm
Made in Germany
KACO blueplanet 7.5 TL3 M2 WM OD IIG0
Part number 1001203
Serial number 00000000000010005 Year Q2 / 16
Input Vmax PV / lsc PV (max) / Inom PV 1000 Vdc /2x 16 A /2x 11 A
V-MPP at Pnom / V- range 350V-800V/200V-800V
Output
Nominal voltage
400V/230V(3/N/PE)
Voltage range continuous operation 3 x 180 Vac - 277 Vac
Current (maximum continuous) 3 x 11,45 A
Frequency range 45Hz-65Hz
Output
Power
Snom at 400 V /230 V Unom 7500 VA
Reactive power cos phi 0-95 % Snom 1 - 0,3 ind/cap
Environ-
ment Temperature range -25°C...+60°C/-13°F...+140°F
Protection class / Ingress protection I/IP65
ARC fault circuit protection non
Interface protection according to country
specific requirements, details see manual
No galvanic separation 4004945
Figure : Name plate

EN
Transportation and Delivery
KACO Operating Instructions blueplanet . TL - . TL Page 
 Transportation and Delivery
Every inverter leaves our factory in proper electrical and mechanical condition. Special packaging ensures that the
units are transported safely. The shipping company is responsible for any transport damage that occurs.
. Scope of delivery
•  inverter
•  wall bracket
•  installation kit
•  set of documentation (DE, EN, quick start guide in other languages)
Checking your delivery
. Inspect your inverter thoroughly.
. Immediately notify the shipping company in case of the following:
–Damage to the packaging that indicates that the inverter may have been damaged
–Obvious damage to the inverter
. Send a damage report to the shipping company immediately.
The damage report must be received by the shipping company in writing within six days following receipt of the
inverter. We will be glad to help you if necessary.
. Transportation
CAUTION
Impact hazard, risk of breakage to the inverter
›Pack the inverter securely for transport.
›Carefully transport the inverter using the carrying handles of the packaging box.
›Do not subject the inverter to shocks.
For safe transportation of the inverter, use the holding openings in the carton.
Packaging
(folding cartons)
(H x W x D (mm))
Total weight [kg]
 x  x 
.
Figure : Transportation of the inverter Table 4: Dimensions and weight

ENEN
Mounting
Page  KACO Operating Instructions blueplanet . TL - . TL
 Mounting
DANGER
Risk of fatal injury from re or explosions
Fire caused by ammable or explosive materials in the vicinity of the inverter can lead to serious
injuries.
›Do not mount the inverter in an area at risk of explosion or in the vicinity of highly ammable mate-
rials.
CAUTION
Risk of burns from hot housing components.
Coming into contact with the housing can cause burns.
› Mount the inverter so that it cannot be touched unintentionally.
Installation location
• As dry as possible, climate-controlled, with the waste heat dissipated away from the inverter
• Air circulation should not be blocked
• When installing the unit in a control cabinet, provide forced ventilation so that the heat is suciently dissipated
• Access to the inverter must also be possible without additional tools
• For outdoor installation, t the inverters in such a way to ensure that they are protected against direct sunlight,
moisture - and dust penetration
• For easy operation, ensure during installation that the display is slightly below eye level.
Wall surface
• Must have adequate load-bearing capacity
• Must be accessible for installation and maintenance
• Must be made out of heat-resistant material (up to °C)
• Flame resistant
• Minimum clearances to be observed during assembly: see Figure  on page .
NOTE
Access by maintenance personnel for service
Any additional costs arising from unfavourable structural or mounting conditions shall be billed to
the customer.
CAUTION
Property damage due to gases that have an abrasive eect on surfaces when they come into
contact with ambient humidity caused by weather conditions.
The inverter housing can be severely damaged by gases (ammonia, sulphur, etc.) if it comes
into with ambient humidity caused by weather conditions.
If the inverter is exposed to gases, it must be mounted so that it can be seen at all times.
›Perform regular visual inspections.
›Immediately remove any moisture from the housing.
›Take care to ensure sucient ventilation of the inverter.
›Immediately remove dirt, especially on vents.
›Failure to observe these warnings may lead to inverter damage which is not covered by the KACO
new energy GmbH manufacturer warranty.

EN
Mounting
KACO Operating Instructions blueplanet . TL - . TL Page 
<20°
Figure : Instructions for wall mounting Figure : Inverter for outdoor installation
CAUTION
Use suitable mounting parts.
›Use mounting material corresponding to or included with the base.
›Mount the inverter upright on a vertical wall only.
›For a free-standing mounting an incline of ° is allowed.
›For upright installation outdoors: Weather-proof base required.
. Unpacking





Figure : Unpacking the unit Figure : Erect the device
Key
1 Carton 4 Opening for erection purposes
2 Protective packaging 5 Centre of gravity
3 inverter

ENEN
Mounting
Page  KACO Operating Instructions blueplanet . TL - . TL
CAUTION
Risk of injury if the body is overloaded!
Lifting the device for transportation or to change location can lead to injuries (e.g. back injuries).
› Only lift the unit using the openings provided.
› The unit must be transported and installed by at least  persons.
Unpacking the unit
ඣThe unit is transported to the installation location.
. Open carton at the front.
. Remove installation material and documentation.
. Pull up top protective packaging for removal.
. Remove inverter from the packaging.
. Place the protective packaging back into the carton.
. Lift the inverter at the intended positions and erect (see Figure  on page ).
» If the unit is in the correct installation position: Proceed with the installation of the wall holder.
. Installing the wall holder
150mm
500 mm
700 mm
250mm
150mm
700 mm
500 mm






1220
510
160
582
920
216
180
Figure : Minimum distances/wall holder Figure : Position of wall holder /
suspension
Key
1 Cover for connection area 4 Wall bracket
2 Screws for mounting (2x Torx) 5 Screws for mounting
3 Bracket with detachment protector 6 Fixings for mounting

EN
Mounting
KACO Operating Instructions blueplanet . TL - . TL Page 
Installing the wall holder
ඣRemove wall holder and mounting kit from the packaging.
. Mark the positions of the drill holes using the slots in the wall holder.
NOTE: The minimum clearances between two inverters, or the inverter and the ceiling/oor have already been
taken into account in the diagram.
. Fix mounting plate to the wall with the supplied mounting xtures.
Make sure that the wall holder is oriented correctly.
» Proceed with the installation of the unit.
. Installing the unit
Figure : Lift the unit
Installing the unit
. Hang the inverter on the wall holder using the suspension brackets on the back of the housing.
. Secure the inverter with the enclosed screw to the detachment protector on the wall holder.
» The mounting of the inverter is complete. Continue with the installation.
NOTE
Power reduction due to heat accumulation.
If the recommended minimum clearances are not observed, the inverter may go into power regula-
tion mode due to insucient ventilation and the resulting heat build-up.
›Maintain minimum clearances.
›Provide for sucient heat dissipation.
FR Attachment of safety label in accordance with UTE C --
The code of practice UTE C -- requires that, upon connec-
tion to the French low-voltage distribution network, a safety
sticker showing a warning to isolate both power sources when
working on the device must be attached to each inverter.
"Attach the provided safety sticker visibly to the outside of
the inverter housing.
ATTEN TIO N
Présence de deux
sources de tension
- Réseau de distribution
-Panneux photovoltaïques
Isoler les deux sources
avant toute intervention

ENEN
Electrical connection
Page  KACO Operating Instructions blueplanet . TL - . TL
Authorised electrician
 Electrical connection
DANGER
Lethal voltages are still present in the terminals and cables of the inverter even after the
inverter has been switched o and disconnected.
Severe injuries or death will occur when touching the cables and terminals in the inverter.
The inverter must only be opened and installed by an accredited electrician, who has been approved
by the public power supplier (country-specic).
The inverter must be mounted in a xed position before being connected electrically.
›Observe all safety regulations and current technical connection specications of the responsible
power supply company.
›Disconnect the AC and DC sides.
›Secure both sides against being inadvertently switched back on.
›Ensure that the AC and DC sides are completely isolated and voltage free.
›Connect the inverter only after the aforementioned steps have been taken.
. Preparing the AC connection
.. Opening and viewing the connection area




5
Figure : Uncover the DC connection Figure : Connection area: Electrical connection
Key
1 Cover to safeguard the DC connections 4 DC connector for PV generator
2 DC isolator switch 5 Housing grounding
3 Screwdriver 6 AC connection socket for grid connection
Open connection area
ඣYou have mounted the inverter on the wall.
. Switch the DC isolator switches to  to remove the cover.
. Carefully unlatch cover at the marked position using a screwdriver.
. Remove cover and store for connection
. Surveying the connection area
» Congure AC connection plug.

EN
Electrical connection
KACO Operating Instructions blueplanet . TL - . TL Page 
Authorised electrician
.. Congure AC connection plug
3
12 4
0,47 In
(12mm)
1,97 In
(50mm)
0,31 In
(8mm)
5
L3
NPEL1
L3
L2
NPE L1
4
Figure : AC connection plug Figure : Remove cable insulation Figure : Connect cable to the con-
tact carrier
1 Nm
1 Nm
CLICK !
CLICK !
30
6,5 Nm
Figure : Tighten screws Figure : Press contact carrier into the
housing
Figure : Tighten the cable screw
tting
Key
1 cable tting 4 Contact plug
2 Seal 5 Cable lengths
3 Housing
Congure AC connection plug
ඣConnection area opened.
. Slide the cable tting over the cable.
. Select seal according to cable diameter used ( ...  mm/  ...  mm/  ...  mm).
. Slide the housing and seal over the cable.
. Remove  mm of the outer cladding.
. Shorten wires N, L, L, L by  mm.
. Strip  mm of the insulation from wires (N, L, L, L , PE).
. With exible wires we recommend the use of wire sleeves conforming to DIN  that are pressed together
using crimping pliers (CRIMPFOX ).
. Insert wires into the contacts in accordance with the markings on the contact carrier.
. Tighten the screws on the contact carrier with  Nm.
. Press contact carriers into the housing with an audible "click".
. Secure the housing with a screwdriver (size ).
Tighten the cable tting using a torque of . Nm.
» Make the electrical connection.

ENEN
Electrical connection
Page  KACO Operating Instructions blueplanet . TL - . TL
Authorised electrician
NOTE
The permissible bending radius of at least  x the cable diameter should be observed during installa-
tion. Excessive bending force may negatively impact the protection rating.
All mechanical loads must be absorbed in front of the connection plug.
.. Cable and fuse requirements
NOTE
Select the following specications in accordance with the following master conditions:
- Country specic installation standards
- Line length
- Type of line installation
- Local temperatures
Note the following cable cross-sections and the required tightening torques:
AC connection DC connection
Max. conductor cross-section
without wire sleeves
2.5 - 6.0 mm² 2.5-6 mm²
(DC plug connector)
Max. conductor cross-section
with wire sleeves
4.0 mm² -
Length of insulation to be
stripped o
12 mm
Tightening torque 1 Nm (on contact carrier)
Table 5: Recommended conductor cross-section
String fuses max. 25 A -
Overvoltage conductor Installed internally, Type III, 1 per MPP tracker
Combiner box - Installed internally
Protection class 3
Overvoltage category III
Table 6: Recommended conductor cross-section/protection device
. Connection to the power grid
The power connection wires are connected on the right of the connection area (see Figure  on page ).
NOTE
If the cable impedance is high (i.e. long grid-side cables), the voltage at the grid terminals of the
inverter will increase during feed-in to the grid. The inverter monitors this voltage. If it exceeds the
country-specic grid overvoltage limit value, the inverter switches o.
›Ensure that the conductor cross-sections are suciently large or that the cable lengths are su-
ciently short.