Kaco blueplanet hybrid 10.0 TL3 User manual

Operating Instructions
█
English translation of German original
Important safety instructions
These instructions form part of the product and must be carefully read, observed and stored in a place which is freely access
ible at all
times.
KACO blueplanet
hybrid 10.0 TL3

EN
Page
2
Legal provisions
The information contained in this document is the property of KACO new energy GmbH. Publication, in whole or in part,
requires the written permission of KACO new energy GmbH.
KACO warranty
You can download the current warranty conditions on the Internet at http://www.kaco-newenergy.com.
Definitions on product designations
In these operating instructions, the product "blueplanet hybrid 10.0 TL3" is referred to as the device for ease of reading.
Trademarks
All trademarks are recognised, even if not explicitly identified as such. A lack of identification does not mean that a prod-
uct or designation/logo is free of trademarks.

EN
blueplanet hybrid 10.0 TL3
Page
3
Contents
1General information....................................................................................................................5
1.1 About this document......................................................................................................................... 5
1.2 Layout of Instructions........................................................................................................................ 5
1.2.1 Symbols used ................................................................................................................................. 5
1.2.2 Safety warnings symbols guide...................................................................................................... 6
1.2.3 Additional information symbols .................................................................................................... 6
1.2.4 Symbols for instructions ................................................................................................................ 6
1.3 Target group...................................................................................................................................... 6
2Safety..........................................................................................................................................7
2.1 Proper use ......................................................................................................................................... 7
2.2 Protection features ........................................................................................................................... 8
3Description of the device ............................................................................................................9
3.1 Mode of operation ............................................................................................................................ 9
3.2 Integrated energy management ....................................................................................................... 9
3.2.1 Operation mode: Self-consumption optimisation with load compensation (Self-Consumption) . 9
3.2.2 Operation mode: Battery Charging................................................................................................ 9
3.2.3 Operation mode: External presetting (External) ........................................................................... 9
3.3 Integration diagram ........................................................................................................................ 10
3.4 Compatible accessories................................................................................................................... 11
3.4.1 KACO blueplanet hy-switch ......................................................................................................... 11
3.4.2 Released battery storage units .................................................................................................... 11
4Technical data........................................................................................................................... 12
4.1 General data.................................................................................................................................... 12
4.2 Detailed technical data ................................................................................................................... 12
4.3 Environmental data......................................................................................................................... 13
5Transportation and Delivery ..................................................................................................... 14
5.1 Scope of delivery ............................................................................................................................. 14
5.2 Transporting the device .................................................................................................................. 14
5.3 Installation tool ............................................................................................................................... 15
6Assembly and preparation ........................................................................................................ 16
6.1 Required material............................................................................................................................ 16
6.2 Choosing the installation location................................................................................................... 17
6.3 Unpacking the device ...................................................................................................................... 18
6.4 Securing the wall bracket ................................................................................................................ 18
6.5 Installing and securing the device ................................................................................................... 20
7Installation................................................................................................................................ 22
7.1 General information........................................................................................................................ 22
7.2 Information regarding electrical connections ................................................................................. 24
7.3 Connecting the device to the power grid........................................................................................ 24
7.3.1 Permissible connectors ................................................................................................................ 25
7.3.2 AC cable fitting assembly ............................................................................................................. 26
7.3.3 Connecting the connector ........................................................................................................... 27
7.3.4 Technical data.............................................................................................................................. 27

EN
blueplanet hybrid 10.0 TL3
Page
4
7.4 Connect PV generator to device ..................................................................................................... 28
7.4.1 Designing the PV generator......................................................................................................... 28
7.4.2 Configuring the DC connector ..................................................................................................... 30
7.4.3 Checking the PV generator for a ground fault............................................................................. 31
7.4.4 Connecting the PV generator ...................................................................................................... 31
7.5 Connecting the battery storage unit to the device......................................................................... 32
7.5.1 Checking the battery storage unit ............................................................................................... 32
7.5.2 Configuring the DC connector ..................................................................................................... 33
7.5.3 Connecting the battery storage unit ........................................................................................... 33
7.6 Connecting KACO blueplanet hy-switch to the device ................................................................... 34
8Commissioning ..........................................................................................................................35
8.1 Hardware commissioning ............................................................................................................... 35
8.2 Configuration with the KACO blueplanet hy-switch software........................................................ 36
8.3 Display............................................................................................................................................. 37
8.3.1 Start display................................................................................................................................. 37
8.3.2 Operating display......................................................................................................................... 38
8.3.3 Selection menu............................................................................................................................ 40
8.3.4 Deactivation in grid-parallel operation ....................................................................................... 43
8.3.5 Warning/fault .............................................................................................................................. 44
8.3.6 Warning display........................................................................................................................... 45
8.4 Update ............................................................................................................................................ 45
9Maintenance and troubleshooting ............................................................................................46
9.1 Visual inspection ............................................................................................................................. 46
9.2 Cleaning .......................................................................................................................................... 47
9.2.1 Cleaning the housing ................................................................................................................... 47
9.3 Warning messages / fault messages / information ........................................................................ 48
9.3.1 List of warning messages............................................................................................................. 48
9.3.2 List of fault messages .................................................................................................................. 51
9.3.3 List of displayed information....................................................................................................... 52
9.4 Other faults ..................................................................................................................................... 53
10 Decommissioning and dismantling ............................................................................................54
10.1 Switching off the device.................................................................................................................. 54
10.2 Uninstalling the device ................................................................................................................... 55
10.2.1 Disconnecting the DC connector ................................................................................................. 56
10.2.2 Disconnecting the communications cable................................................................................... 56
10.2.3 Disconnecting the AC connector ................................................................................................. 56
10.3 Disassembling the device................................................................................................................ 57
10.4 Packaging the device....................................................................................................................... 57
10.5 Storing the device ........................................................................................................................... 57
11 Disposal.....................................................................................................................................58
12 Service and warranty.................................................................................................................58

EN
blueplanet hybrid 10.0 TL3
Page
5
1General information
1.1 About this document
Other applicable documents
During installation, observe all assembly and installation instructions for components and other parts of the system.
These instructions also apply to the equipment, related components and other parts of the system.
Some of the documents required for the registration and approval of your system are included with the
operating instructions.
Links to more detailed information can be found at www.kaco-newenergy.com.
Document title
Document type
Technical data sheet
Technical information on the product
hy-sys software documentation Application note – Operating the software tool for monitor-
ing and configuration
Grid protection and safety parameters
Default parameters
Application note
Software package hy sys
ZIP files for current software
EU Declaration of Conformity
Country-specific certificates
Certification for specific subassembly
Certificates
Storing the documents
These instructions and other documents must be stored near the system and be available at all times.
The current version of the operating Instructions can be downloaded at www.kaco-newenergy.com.
English translation of German original
These operating instructions have been produced in several languages. The German-language version of the operating
instructions is the original version. All other language versions are translations of the original operating instructions.
WARNING
Improper handling of the device can be hazardous!
›You must have read and understood the operating instructions in order to install and use the device
safely!
1.2 Layout of Instructions
1.2.1 Symbols used
General hazard Fire and risk of explosion
Electrical voltage Risk of burns
Earthing - ground conductor Waiting time after discharge
The tasks indicated with this symbol may only be carried out by an authorised
electrician.
Authorised electrician

EN
blueplanet hybrid 10.0 TL3
Page
6
1.2.2 Safety warnings symbols guide
DANGER
High risk
Failure to observe this warning will lead directly to serious bodily injury or death.
WARNING
Potential risk
Failure to observe this warning may lead to serious bodily injury or death.
CAUTION
Low-risk hazard
Failure to observe this warning will lead to minor or moderate bodily injury.
CAUTION
Risk of damage to property
Failure to observe this warning will lead to property damage.
1.2.3 Additional information symbols
NOTE
Useful information and notes
Information that is important for a specific topic or objective, but that is not safety-relevant.
1.2.4 Symbols for instructions
Prerequisite for use
1Carry out the next step
1. Additional action sequence
Interim result of the action
» End result
1.3 Target group
All activities described in the document may only be carried out by specially trained personnel with the following qualifi-
cations:
Knowledge about how an inverter functions and operates
Training in the handling of hazards and risks during the installation and operation of electrical devices and systems.
Education concerning the installation and start-up of electrical devices and systems.
Knowledge of applicable standards and directives.
Knowledge and adherence to this document with all safety notices.

EN
blueplanet hybrid 10.0 TL3
Page
7
2Safety
Before using the product for the first time, please read through the safety instructions carefully.
DANGER
Lethal voltages are still present in the connections and cables of the device even after the device has
been switched off and disconnected!
Severe injuries or death may occur if the cables and/or terminals/busbars in the device are touched.
›The device must be mounted in a fixed position before being connected electrically.
›Comply with all safety regulations and current technical connection specifications of the responsible
power supply company.
›The device is only permitted to be opened or serviced by a qualified electrician.
›Switch off the grid voltage by turning off the external circuit breakers.
›Check that all AC and DC cables are completely free of current using a clip-on ammeter.
›Do not touch the cables and/or terminals/busbars when switching the device on and off.
›Keep the device closed when in operation.
The electrician is responsible for observing all existing standards and regulations. The following applies:
Keep unauthorised persons away from the device and/or system.
In particular, making sure that the locally applicable version of the standard 1"Requirements for special installations or
locations – solar photovoltaic (PV) power supply systems" is observed.
Ensure operational safety by providing proper grounding, conductor dimensioning and appropriate protection against
short circuiting.
Observe all safety instructions on the product and in these operating instructions.
Switch off all voltage sources and secure them against being inadvertently switched back on before performing visual
inspections and maintenance.
When taking measurements on the live device:
–Do not touch the electrical connections
–Remove all jewellery from wrists and fingers
–Ensure that the testing equipment is in safe operating condition.
Modifications to the surroundings of the device must comply with the applicable national and local standards.
2.1 Proper use
The device is a transformerless PV inverter which converts the direct current of the PV generator into grid-compatible
three-phase alternating current and then feeds the three-phase alternating current into the public power grid. In addi-
tion, the device consists of a bidirectional, transformerless inverter for charging and discharging released battery storage.
The device is built using state-of-the-art technology and in accordance with the recognized safety rules. Nevertheless,
improper use may cause lethal hazards for the operator or third parties, or may result in damage to the product and other
property.
1
Country
Standard
EU Harmonised document - HD 60364-7-712 (European im-
plementation of the IEC standard)
Examples of standards specific to business premises

EN
blueplanet hybrid 10.0 TL3
Page
8
The device is intended for use in air-conditioned indoor rooms and may only be used in countries for which it has been
approved or for which it has been released by KACO new energy and the grid operator.
Operate the device only with a permanent connection to the public power grid. The country and grid type selection must
be commensurate with the respective location and grid type.
The requirements of the grid operator must be met for grid connection to take place. The permission of the relevant au-
thorities may also be required in order to secure authorisation to connection to the grid.
The enclosed documentation is an integral part of the product. The documentation must be read, observed and stored in
a place which is freely accessible at all times.
The name plate must be permanently attached to the product.
Any other or additional use of the device shall be regarded as improper.
This includes:
Use of a distribution system that is not described (grid type)
Use of sources other than PV-strings.
Mobile use
Use in rooms where there is a risk of explosion
Use in direct sunlight, rain or a storm or other harsh environmental conditions
Use in an outdoor area that does not meet the environmental conditions set down in Technical Data > Environmental
Data.
Operation outside the specification intended by the manufacturer
Overvoltage of more than 1000 V on the DC connection
Modifying the device
Usage of unreleased battery storage
2.2 Protection features
The following monitoring and protection functions are built-in:
Overvoltage conductor / varistor to protect the power semiconductors from high-energy transients on the grid and
generator sides.
Device temperature monitoring system
EMC filter to protect the inverter from high-frequency grid interference
ISO/AFI detection of an isolation fault on the generator.

EN
blueplanet hybrid 10.0 TL3
Page
9
3Description of the device
3.1 Mode of operation
The device ensures the supply of the consumers in the household from three different sources:
photovoltaics, energy storage unit and the public power grid. If there is sufficient solar radiation on the photovoltaic sys-
tem and thus a certain minimum voltage is applied to the device, the start process begins. The feed-in process begins
once the PV generator has passed the insulation test and the grid parameters are within the requirements imposed by
the grid operator for a specific monitoring time. The inverter remains in operation as long as it is supplied from the photo-
voltaic system or battery storage unit. If the supply voltage is too low, it shuts down until the voltage of the photovoltaic
system reaches the minimum value again.
The power of the photovoltaic system is used to supply consumers and charge the energy storage unit. This means that
the energy generated can be used to supply loads with a time delay. If sufficient power cannot be provided by the photo-
voltaic system and the energy storage unit, the missing energy is taken from the public grid.
It is possible to use both integrated energy management and suitable external energy management. The selection is
made in the blueplanet hy-sys software belonging to the device.
3.2 Integrated energy management
The device has integrated energy management. It is designed for mains parallel operation with load compensation. To use
load compensation, the KACO blueplanet hy-switch is required as measuring point. The settings for integrated energy
management are made in the blueplanet hy-sys software.
3.2.1 Operation mode: Self-consumption optimisation with load compensation (Self-Consumption)
If the photovoltaic system supplies energy, priority is given to connected loads. If the photovoltaic system has a surplus of
energy, the energy storage unit is charged with it. When the energy storage unit is fully charged and there is still a surplus
of energy, this energy is fed into the public grid. If the charging capacity of the energy storage unit has a limiting effect, it
can be fed into the public power grid in parallel with the storage unit charging. The feed-in power into the public power
grid can be limited to a freely selectable maximum power during installation. If the power of the photovoltaic system is
not sufficient to supply the load, the energy storage unit is discharged to fully supply the load. If the discharge capacity of
the energy storage unit is not sufficient, energy is taken from the public power grid.
3.2.2 Operation mode: Battery Charging
Priority battery charging is used to maximise the charge level of the energy storage unit. If the photovoltaic system sup-
plies energy, priority is given to connected loads, provided this is possible by the hardware for load compensation. The
excess energy is used to charge the energy storage unit with the maximum possible power. If there is an energy surplus,
this energy is fed into the public grid. The maximum photovoltaic feed-in power into the public grid can be set by the in-
staller.
3.2.3 Operation mode: External presetting (External)
Functionally, this operation mode corresponds to Operation mode: Self-consumption optimisation with load compensa-
tion (Self-Consumption)3.2.1. In addition, the hybrid inverter is controlled by an external energy management system
whose default values take precedence over the integrated energy management system. In this case, compliance with the
relevant standards must be ensured by the system operating company.

EN
blueplanet hybrid 10.0 TL3
Page
10
3.3 Integration diagram
Fig. 1: Diagram of the system
Legend
Definition / information on the connection
PV generator The PV generator converts the radiant energy of sunlight
into electrical energy (direct current).
Inverter The PV generator is connected to the device's DC connec-
tion.
Inverter fuse protection (line protection)
The circuit breaker is an overcurrent protection device.
Power supply company counter The feed-in counter and reference counter are to be speci-
fied and installed by the power supply company. Some
power supply companies also allow the installation of your
own calibrated counters.
All-pole disconnection Use the DC isolator switch to disconnect the device from
the PV generator.
Battery Excess power is stored in the battery storage unit until it is
used again.

EN
blueplanet hybrid 10.0 TL3
Page
11
3.4 Compatible accessories
3.4.1 KACO blueplanet hy-switch
KACO blueplanet hy-switch is used to record the power at the grid connection point or the installation string to be com-
pensated by the device. This measured value is transmitted to the device via data communication between the device
and KACO blueplanet hy-switch. This enables the integrated energy management system to adjust for the load to be com-
pensated and to perform this adjustment very quickly. KACO blueplanet hy-switch is required for grid-parallel installations
with a battery storage unit.
Features of KACO blueplanet hy-switch:
–Energy consumption recording for optimisation
of self-consumption
–In case of power failure, all poles are disconnected from the
public power grid
Integrated current sensors up to 50A
–3 x 3.5mm jack connector for expandability with
external current sensors up to 100A
–RJ45 connector for communication between
KACO blueplanet hy-switch and the device
Fig. 2: KACO blueplanet hy-switch
For further information, please refer to the KACO blueplanet hy-switch manual. The design of the communication port is
described in chapter 7.6.
3.4.2 Released battery storage units
The following battery storage units are included in the current version 7.x of the device software.
Tab. 1: Released battery storage units
Vendor
Type
Capacity (approx.)
BYD
Battery-Box H
5.1 bis 10.2 kWh
BYD
Battery-Box Premium HVS
5.1 bis 10.2 kWh
BYD
Battery-Box Premium HVM
8.3 bis 22.1 kWh
Energy Depot
DOMUS 2.5
5.0 bis 20.0 kWh
Energy Depot
DOMUS 3.6
7.2 bis 28.8 kWh
The current release list can be found in the download area of the KACO new energy homepage.
General information on connecting the battery storage unit to the device can be found in chapter 7.5.
Please consult the manual of the battery manufacturer.

EN
blueplanet hybrid 10.0 TL3
Page
12
4Technical data
4.1 General data
Fig. 3: KACO blueplanet hybrid 10.0 TL3 inverter
Features of blueplanet hybrid 10.0 TL3
–3-phase 10 kW hybrid inverter
–2 integrated MPP trackers
–Fast load regulation (<100 ms)
–High efficiency:
PV grid = >98%
PV battery = >97%
Battery grid = >97%
–Pure sinusoidal output voltage
–Operation modes: Grid operation,
Compensation mode
–Aluminium housing
–Convection cooling
–All connections are plug-and-play
4.2 Detailed technical data

EN
blueplanet hybrid 10.0 TL3
Page
13
Additional technical data according to IEC 62109-2
Input levels Max. input source feedback current 0
Output levels Initial short-circuit alternating current (Ik" first single period effec-
tive value)
16.4 A
Inrush current 1.7 A
4.3 Environmental data
Table 1: Environmental data
Installation height
<2,000 m
Ambient temperature
+5°C + 40°C
Protection rating (KACO installation location)
IP20
Humidity range (non-condensing) [%]
20 - 90

EN
blueplanet hybrid 10.0 TL3
Page
14
5Transportation and Delivery
Every product leaves our factory in perfect electrical and mechanical condition. Special packaging ensures that the de-
vices are transported safely. The shipping company is responsible for any transport damage that occurs.
5.1 Scope of delivery
The following parts and components are supplied with the device:
Inverter 3 pairs of DC connectors
(SUNCLIX connectors)
1 x AC connector (Phoenix
Contact PRC 5-FC-FS6 12-1)
2 x countersunk screw M4x20mm
(already pre-assembled)
Wall bracket
(already pre-assembled)
Manual
Check the equipment included
1. Carefully inspect the device for transport damage; check the scope of supply.
2. Immediately notify the shipping company in case of the following:
–Damage to the packaging that indicates that the device may have been damaged.
–Obvious damage to the device.
3. Send a damage report to the shipping company immediately.
4. The damage report must be received by the shipping company in writing within six days following receipt
of the device. We will be glad to help you if necessary.
5.2 Transporting the device
CAUTION
Risk of injury caused by excessive physical strain
Lifting the device, for transport, relocation and assembly, can result in injuries (e.g. back injuries).
›The device must be transported and installed by at least 2 persons.
CAUTION

EN
blueplanet hybrid 10.0 TL3
Page
15
Hazard due to impact; risk of breakage to the device!
›Pack the device securely for transport.
›Transport the device using the intended carrying handles of the packaging box.
›Do not expose the device to any shocks.
Packaging: Folding cardboard box
Packaging size: 720 x 685 x 320 mm
Total weight, including packaging 40Kg
5.3 Installation tool
The codes given in the table below are used in all usage instructions for assembly/installation/maintenance and disassem-
bly for the tools and tightening torques being used.
Tab. 2: Key and description of tool codes
Code (s) Contour of the
connector
W
External hexagon
A
Internal hexagon
T
Torx
S
Slot
Fig. 5: Form pattern
Fig. 4: Cardboard box (exemplary)

EN
blueplanet hybrid 10.0 TL3
Page
16
6Assembly and preparation
CAUTION
Risk of injury caused by excessive physical strain
Lifting the device, for transport, relocation and assembly, can result in injuries
(e.g. back injuries).
›The device must be transported and installed by at least 2 persons.
6.1 Required material
Solar cable
For the connection of the PV generator to the device. It can also be used to connect the battery; refer to the battery man-
ufacturer's manual.
–Only designated solar cables are permitted, either type PV1-F
or UL-certified solar cables (ZKLA), AWG 10-14.
Table 2: Technical requirements for solar cables
Technical data according to standard EN 50521 UL 6703
Ambient temperature -40°C…+85°C -40°C…+70°C
Max. nominal voltage 1100 VDC 600 VDC
Max. nominal current 2.5 mm² - 27 A;
4.0 mm² - 40 A;
6.0 mm² - 40 A
AWG 14 - 15 A;
AWG 12 - 20 A;
AWG 10 - 30 A
Cable diameter
5 ... 8 mm
5 ... 8 mm
NOTE
Observe the manufacturer's instructions of the manufacturer of the connector.
To use the provided SUNCLIX connectors, use only solar cables with a nominal cross section between
2.5 mm² and 6 mm².
›Please observe the information on nominal voltage and nominal current.
›Protect the connectors from moisture and dirt.
Connecting cable for the battery storage unit
If specific connection cables have been supplied by the battery manufacturer, these cables must be used. To be on the
safe side, make sure that SUNCLIX connectors are installed on the side of the device.
Communication cable
Patch cable for communication with KACO blueplanet hy-switch, the battery and the Internet. An RJ45 connector must be
fitted on the device side. The cable must comply with CAT 5E S/FTP. The length depends on the installation location, but
should not exceed 20m. Cross-over assignments cannot be used.
Wall bracket fixing materials
–4x fixings
–4x fixing screw min. Ø6mm, minimum length 40mm
–4x plain washer matching the screw, outer Ø max. 20mm

EN
blueplanet hybrid 10.0 TL3
Page
17
6.2 Choosing the installation location
DANGER
Risk of fatal injury due to fire or explosions!
Fire caused by flammable or explosive materials in the vicinity of the device can lead to serious injuries.
›Do not mount the inverter in potentially explosive atmospheres or in the vicinity of highly flammable
materials.
CAUTION
Property damage due to gases that have an abrasive effect on surfaces when they come into contact
with ambient humidity caused by weather conditions.
The device housing can be seriously damaged due to gases in combination with air humidity resulting from
weather conditions (e.g. ammonia, sulphur).
›If the device is exposed to gases, the installation must be carried out at observable locations.
›Perform regular visual inspections.
›Immediately remove any moisture from the housing.
›Ensure adequate ventilation at the installation location.
›Immediately remove dirt, especially on vents.
›Failure to observe these warnings may lead to device damage which is not covered by the manufac-
turer warranty.
NOTE
Access by maintenance personnel for service
Any additional costs arising from unfavourable structural or mounting conditions shall be billed to the cus-
tomer.
Requirements for the installation space
–As dry as possible, climate-controlled, the waste heat must be able to be dissipated away from the device.
–Unobstructed air circulation.
–Observe ambient temperatures according to the data sheet.
–Observe minimum distances to the sides of the housing; see Fig. 7.
–Accessible from the front and sides without requiring additional resources.
–At a height at which the display can be read at any time.
–Do not install outdoors; the device is designed for indoor use only (IP20).
Requirements on the installation surface
–Must have adequate load-bearing capacity
–Must be accessible for installation and maintenance
–Must be made of heat-resistant material (up to 90 °C)
–Must be flame resistant

EN
blueplanet hybrid 10.0 TL3
Page
18
6.3 Unpacking the device
CAUTION
Property damage as a result of condensation
Faulty storage can form condensate in the device and impair the device functioning (e.g. storage outside
the ambient conditions or temporary relocation from a cold to a hot environment).
›Prior to installation, check the inner area for condensation and if necessary, allow it to dry sufficiently
before installation.
Unpacking the device
1. Loosen packaging tape from cardboard box.
2. Open the carton at the top. Be careful not to damage the device when using sharp objects.
3. Remove installation material and documentation.
4. Reach through the housing and slide the device out of the carton.
5. Remove the protective packaging from the housing.
6. Remove the wall bracket from the back of the device by loosening and removing the locking screws
according to Fig. 6 [ T_TX20/ 1.5Nm].
Fig. 6: Position of the locking screws
6.4 Securing the wall bracket
CAUTION
Hazard when using unsuitable fixing materials!
If unsuitable fixing materials are used, the device could fall and persons in front of the device may be seri-
ously injured.
›Use only fixing materials that are suitable for the mounting base.
›Only install the devices upright and side by side.

EN
blueplanet hybrid 10.0 TL3
Page
19
Fig. 7: Minimum distances around the device Fig. 8: Prohibited mounting position
NOTE
Side distance
The minimum side distance corresponds both to the distance to structural elements and to the total dis-
tance between two devices.
NOTE
Do not mount two devices one above the other!
The devices may only be mounted side by side. When mounted one above the other, the warm air escap-
ing from the lower device can impair the function of the upper device.
The appropriate screw connection (fixings and screws) is selected and provided by the installer, taking the wall thickness
and material into consideration. The wall bracket must be firmly screwed to the wall with the four suitable screws.
Fig. 9: Drill hole dimensions

EN
blueplanet hybrid 10.0 TL3
Page
20
Procedure for mounting the wall bracket
The wall bracket must be removed from the back of the device. (cable ties)
1. Remove the wall bracket from the device.
2. Determine the mounting position of the device. Check the observance of the minimum distances ( Fig. 7).
3. Hold the wall bracket horizontally in position as a template.
4. Mark the position of the drill holes using the recess in the wall bracket, or mark them according to the
dimensions in Fig. 9.
5. Determine the size of the drill holes according to the fixing material and drill holes.
6. Fix the wall bracket to the wall with suitable fixing material (see 6.1).
7. Check the wall bracket for a firm seat.
6.5 Installing and securing the device
CAUTION
Risk of injury from improper lifting and transport
If the device is lifted improperly, it can tilt and result in a fall.
›Always lift the device vertically.
›Use a climbing aid for the chosen installation height.
›Wear protective gloves and safety shoes when lifting and lowering the device.
NOTE
Power reduction due to heat accumulation!
If the recommended minimum clearances are not observed, the device may reduce the power due to insuf-
ficient ventilation and the resulting heat build-up.
›Observe minimum clearances and provide for sufficient heat dissipation.
›All objects on the device housing must be removed during operation.
›Ensure that no foreign bodies prevent heat dissipation following device installation.
Lifting and installing the device
The mount has been installed.
1. The device is tilted slightly to the rear. Both hooks of the wall bracket must engage into the bolts of the outer
cooling fins. When inserting, make sure that the hooks are not bent. When the bolts are hooked into the wall
bracket, the device is carefully tilted down until it is parallel to the wall.
Fig. 10: Installation