Kaiweets HT106E User manual

KAMEETS EX
RECEPTACLE TESTER #riose 43
INSTRUCTIONS
Designed to detect common wiring problems in
- — e
AL
=000 =22
PO T
standard and RCD receptacles. In addition, the
tester with the LCD can measure the socket voltage.
Diagnostics chart
Indicator Condition Explanation
CORRECT
Receptacle is wired correctly
OPEN GROUND
Ground contact is not connected; Ground
wire is not connected to the ground.
OPEN NEUTRAL Neutral contact is not connected
OPEN HOT Hot contact is not connected
HOT/GRD REVERSE
Hot and ground connections are
reversed
HOT/NEU REVERSE
Hot and neutral connections are
reversed
HOT/GRD REVERSE,
OPEN GRD
Reverse connection between the
hot line and ground line, and the
ground line is unconnected.
* o Indicator llluminated © Indicator Not llluminated
Note: This tester cannot distinguish reverse connection between neutral line
and ground line.

Questions or Concern support@kaiweet:
A Warning
Read, understand, and follow all warnings and instructions before operating
testers. Failure to follow instructions could result in death or serious injury.
Before each use, verify tester operation by testing on a known live and
correctly wired receptacle. Do not use if the tester appears damaged in
any way.
The tester is intended for indoor use only. Other equipment or devices
attached to the circuit being tested could interfere with the tester, clear the
circuit before testing.
This tester only detects common wiring problems. Always consult a qualified
electrician to resolve wiring problems
Wiring Configuration Testing
Conditions indicated: wiring correct, open ground, reverse polarity, open
hot, open neutral and hot/ground reversed.
Conditions NOT indicated: quality of ground, muliple hot wires, combinations
of defects, reversal of grounded and grounding conductors.
All appliances or equipment on the circuit being tested should be unplugged
to help reduce the possibility of erroneous readings

Standard Receptacles
1. Verify tester operation by testing on a known live and correctly wired
receptacle.
2. Plug tester into receptacle.
3. Compare the illuminated lights on the tester to the key code printed on the
tester.
4. If the tester indicates that the receptacle is not wired correctly, consult a
qualified electrician.
Note:
1. The test time should be no more than 5 minutes.
2. When using, please be careful not to touch the RCD button, so as not to
trigger the leakage protection switch and cause unnecessary loss.
RCD Receptacles
1. Check the RCD receptacle user manual for information on how the specific
receptacle operates prior to using this tester.
2. Insert the tester into the receptacle under test to check for correct wiring.
Lights on the tester should illuminate. Only press the RCD button when the
lights are illuminated as “eso” (CORRECT).
3. Press the test button on the RCD receptacle. The RCD light should illuminate.
Did the the RCD trip and all lights on the tester go dark?
YES: Reset the RCD by pressing the reset button. The RCD is operating
properly.
NO: Proceed to step 4.
4. Did the RCD light illuminate?
YES: The RCD is not operating properly or the receptacle is miswired
Consult a qualified electrician.
NO: The tester is not operating properly. Please contact us for product
warranty.

veo
ceo
RCD Light
Voltage Test
Insert the tester into a standard socket of UK. Read the socket voltage value
from the tester screen, the unit is V.
Measuring Range: 48~250V/45~65Hz; Accuracy: + (2.0%+2)
Clean
Wipe with a clean, dry lint-free cloth. Do not use abrasive cleaners or solvents.
Technical specifications
Operating voltage: 48~250V/ 45~65Hz
Operating temperature: 0°C~40°C
* Operating humidity: 20%~75%RH
« Storage temperature: -10°C~50°C UK Authorized Representative
Company rame: ¥ Consling Liied
« Storage humidity: 20%~80%RH ndarss: /0 H Consling Limted Ofice 47,
Gonturon House Longon ood, Siaies o
* Altitude: <2000m ThamosStanes, Sutey, London, TWIB 4K
To 4407514677868
RCD test: >30mA Emai H2YHUKGamatcom
CERoHS & 2 A @ES