Kaiweets KM117B User manual

KAIWEETS
RECEPTACLE TESTER
KM117B INSTRUCTION
Designed to detect common wiring
problems in standard and GFCI receptacles.
In addition, the tester with the LCD can measure the Phase Voltage,
Leakage Voltage and Current
Diagnostics chart
Indicator | Condition Explanation
CORRECT Receptacle is wired correctly
OPEN GROUND
Ground contact is not connected;|
Ground wire is not connected to the|
ground.
OPEN NEUTRAL
Neutral contact is not connected
HOT/GRD
REVERSE
Hot and ground connections are
reversed
HOT/NEU
REVERSE
Hot and neutral connections are|
reversed
HOT/GRD
REVERSE, OPEN
GRD
Reverse connection between the)|
hot line and ground line, and the|
ground line is unconnected.
@ Indicator llluminated O Indicator Not llluminated
[email protected]
Questions or Concern?
Note: This tester cannot distinguish reverse connection between neutral
line and ground line.
/\ Warning
Read, understand and follow all warnings and instructions before
operating testers. Failure to follow instructions could result in death or
serious injury.
e Before each use, verify tester operation by testing on a known live
and correctly wired receptacle. Do not use if the tester appears
damaged in any way.
e Thetester is intended for indoor use only. Other equipment or devices
attached to the circuit being tested could interfere with the tester,
clear the circuit before testing
e This tester only detects common wiring problems. Always consult
qualified electrician to resolve wiring problems
Neutral (White) Hot (Black)
Ground (Green)

KAIWEETS
RECEPTACLE TESTER
KM117B INSTRUCTION
Designed to detect common wiring
problems in standard and GFCI receptacles.
In addition, the tester with the LCD can measure the Phase Voltage,
Leakage Voltage and Current
Diagnostics chart
Indicator | Condition Explanation
CORRECT Receptacle is wired correctly
OPEN GROUND
Ground contact is not connected;|
Ground wire is not connected to the|
ground.
OPEN NEUTRAL
Neutral contact is not connected
HOT/GRD
REVERSE
Hot and ground connections are
reversed
HOT/NEU
REVERSE
Hot and neutral connections are|
reversed
HOT/GRD
REVERSE, OPEN
GRD
Reverse connection between the)|
hot line and ground line, and the|
ground line is unconnected.
@ Indicator llluminated O Indicator Not llluminated
[email protected]
Questions or Concern?
Note: This tester cannot distinguish reverse connection between neutral
line and ground line.
/\ Warning
Read, understand and follow all warnings and instructions before
operating testers. Failure to follow instructions could result in death or
serious injury.
e Before each use, verify tester operation by testing on a known live
and correctly wired receptacle. Do not use if the tester appears
damaged in any way.
e Thetester is intended for indoor use only. Other equipment or devices
attached to the circuit being tested could interfere with the tester,
clear the circuit before testing
e This tester only detects common wiring problems. Always consult
qualified electrician to resolve wiring problems
Neutral (White) Hot (Black)
Ground (Green)

Wiring Configuration Testing
Conditions indicated: CORRECT, OPEN GROUND, OPEN NEUTRAL,
HOT/GRD REVERSE, HOT/NEU REVERSE, HOT/GRD REVERSE, OPEN
GRD.
Conditions NOT indicated: Quality of ground, multiple hot wires,
combinations of defects, reversal of grounded and grounding conductors.
All appliances or equipment on the circuit being tested should be
unplugged to help reduce the possibility of erroneous readings.
GFCI Receptacles
1. Check the GFCI receptacle user manual for information on how
the specific receptacle operates prior to using this tester.
2. Insert the tester into the receptacle under test to check for correct
wiring. Lights on the tester should illuminate.
3. Read Current, Phase Voltage (L_ N) and Leakage Voltage (N_ E)
4. Press the test button on the GFCI receptacle. Only press the GFCI
button when the lights are illuminated as “esc” (CORRECT). The
GFClI light should illuminate. Did the GFCI trip and all lights on the
tester go dark?
YES: Reset the GFCI by pressing the reset button. The GFCI is
operating properly.
NO: Proceed to step 5.
5. Did the GFCI light illuminate?
YES: The GFCI is not operating properly or the receptacle is miswired
Consult a qualified electrician.
NO: The tester is operating properly.
GFCI Light —
Note:
1. The test time should be no more than 5 minutes.
2. When using, please be careful not to touch the GFCI button, so as not to
trigger the leakage protection switch and cause unnecessary loss.
3. When checking the circuit, please turn off the household appliances
in use and confirm that the power failure will not cause any safety hazards.
Voltage Test
Insert the tester into a standard three holes power outlet. Read Phase
Voltage (L_ N) and Leakage Voltage (N_ E).
The N-E voltage is normally "0 or closes to "0 If the N-E voltage reading is
100 large, the LCD Screen will change from green to orange. The following
reasons:
1. The power consumption is too large, the wire is too small or too long
(the resistance is too large).
2. The neutral line connector is loose, has poor contact or is oxidized.
3. The neutral wire is disconnected or severely oxidized, the electrical
appliances cannot form a loop and there is a pressure drawdown
generated by the electrical appliances between the neutral wire and the
ground wire (determined by the pressure drawdown of the load electrical
appliances).

Wiring Configuration Testing
Conditions indicated: CORRECT, OPEN GROUND, OPEN NEUTRAL,
HOT/GRD REVERSE, HOT/NEU REVERSE, HOT/GRD REVERSE, OPEN
GRD.
Conditions NOT indicated: Quality of ground, multiple hot wires,
combinations of defects, reversal of grounded and grounding conductors.
All appliances or equipment on the circuit being tested should be
unplugged to help reduce the possibility of erroneous readings.
GFCI Receptacles
1. Check the GFCI receptacle user manual for information on how
the specific receptacle operates prior to using this tester.
2. Insert the tester into the receptacle under test to check for correct
wiring. Lights on the tester should illuminate.
3. Read Current, Phase Voltage (L_ N) and Leakage Voltage (N_ E)
4. Press the test button on the GFCI receptacle. Only press the GFCI
button when the lights are illuminated as “esc” (CORRECT). The
GFClI light should illuminate. Did the GFCI trip and all lights on the
tester go dark?
YES: Reset the GFCI by pressing the reset button. The GFCI is
operating properly.
NO: Proceed to step 5.
5. Did the GFCI light illuminate?
YES: The GFCI is not operating properly or the receptacle is miswired
Consult a qualified electrician.
NO: The tester is operating properly.
GFCI Light —
Note:
1. The test time should be no more than 5 minutes.
2. When using, please be careful not to touch the GFCI button, so as not to
trigger the leakage protection switch and cause unnecessary loss.
3. When checking the circuit, please turn off the household appliances
in use and confirm that the power failure will not cause any safety hazards.
Voltage Test
Insert the tester into a standard three holes power outlet. Read Phase
Voltage (L_ N) and Leakage Voltage (N_ E).
The N-E voltage is normally "0 or closes to "0 If the N-E voltage reading is
100 large, the LCD Screen will change from green to orange. The following
reasons:
1. The power consumption is too large, the wire is too small or too long
(the resistance is too large).
2. The neutral line connector is loose, has poor contact or is oxidized.
3. The neutral wire is disconnected or severely oxidized, the electrical
appliances cannot form a loop and there is a pressure drawdown
generated by the electrical appliances between the neutral wire and the
ground wire (determined by the pressure drawdown of the load electrical
appliances).

/
Green Orange
o SASETY e ST v
it I8y Tey 0w iddy Oy
Cewors
(
4
q
Iq
q
(
Normal Safety Hazard
Note:
‘When the socket connection is not correct, the leakage voltage cannot
be measured.
Clean
Wipe with a clean, dry lint-free cloth. Do not use abrasive cleaners or
solvents.
Technical specifications
Operating voltage: 90~250V/45~65Hz
Phase voltage: 90~250V/45~65Hz accuracy: +(2.0%+2)
Leakage voltage: 0~99V /45~65Hz accuracy, +(2.0%+2)
Operating temperature: 0°C~40°C
Operating humidity: 20%~75%RH
Storage temperature: -10°C~50°C
Storage humidity: 20%~80%RH
Altitude: £2000m
GFCl test: >5mA
L]
L]
L]
.
L]
L]
.
L]
L]
® GFCl working voltage: 110V+20V
UK |REP
UK Authorized Representative
‘Company name: YH Consuling Limtod
‘Address: CI0 YH Gonsulting Limited Offica 47,
Gonturion House, London Road, Stains-upon-
ThamesSiaines, Surtey, Londan, TW1B 4AX
Tol:+44 07514.677668
Email: H2YHUK@gmall com
(CERRHEFCE

/
Green Orange
o SASETY e ST v
it I8y Tey 0w iddy Oy
Cewors
(
4
q
Iq
q
(
Normal Safety Hazard
Note:
‘When the socket connection is not correct, the leakage voltage cannot
be measured.
Clean
Wipe with a clean, dry lint-free cloth. Do not use abrasive cleaners or
solvents.
Technical specifications
Operating voltage: 90~250V/45~65Hz
Phase voltage: 90~250V/45~65Hz accuracy: +(2.0%+2)
Leakage voltage: 0~99V /45~65Hz accuracy, +(2.0%+2)
Operating temperature: 0°C~40°C
Operating humidity: 20%~75%RH
Storage temperature: -10°C~50°C
Storage humidity: 20%~80%RH
Altitude: £2000m
GFCl test: >5mA
L]
L]
L]
.
L]
L]
.
L]
L]
® GFCl working voltage: 110V+20V
UK |REP
UK Authorized Representative
‘Company name: YH Consuling Limtod
‘Address: CI0 YH Gonsulting Limited Offica 47,
Gonturion House, London Road, Stains-upon-
ThamesSiaines, Surtey, Londan, TW1B 4AX
Tol:+44 07514.677668
Email: H2YHUK@gmall com
(CERRHEFCE