Kampa Fiesta AIR Pro 280 User manual

Fiesta AIR & Fiesta AIR Pro
280, 350 & 420
Instructions & care manual
Some of the images shown in these instructions are other similar Kampa awnings and
are for illustration purposes only.
The Fiesta is a registered design exclusive to Kampa UK Limited
2
IMPORTANT - PLEASE READ:
Under certain conditions all awnings will suffer from internal condensation.
Depending upon the atmospheric conditions, the weather and the amount of
moisture in the ground, the condensation could be quite severe and is
commonly mistaken for leaking, especially as it can run down the inside of the
roof and drips off ties tapes and other internal fittings. If you suspect your
awning is leaking it is almost certainly condensation. Laying a waterproof
groundsheet (not a breathable carpet) throughout the whole awning will help
and condensation can also be improved by ensuring adequate ventilation. On
some awnings we offer an optional roof lining that can also help prevent
condensation and catch any drips of condensation that fall from the roof.
The awning material has a waterproof PU coating over its entire surface and
the main seams of your awning have been factory taped to help prevent
leakage. Depending upon your expectations, it may be necessary to treat the
remaining seams with a seam sealant. Seams treated with seam sealant
cannot leak. Seam sealant should also be applied to areas where the taping is
damaged or has peeled away through wear and tear. It can also be applied to
areas where a leak may have developed. Seam sealant is available from your
dealer.
The awning beading is sewn to the awning with a special waterproof sewing
thread. This thread swells when wet to fill the needle holes but thread needs
to become wet several times before it is totally effective. This process is known
as ‘weathering’ and it may take several soakings for the weathering to be fully
effective. This area can also be treated with seam sealant.
WELCOME
Thank you for purchasing your Kampa awning. Please read these
instructions carefully before attempting to set up your awning and retain for
future reference. If used properly, your awning should give you years of
trouble free use. We recommend that your awning is insured against
accidental and storm damage as this is not covered by the warranty.
This awning is designed for use in light to moderate weather. During strong
winds or snowfall we recommend that you take your awning down. The
awning is designed for touring use; it is not designed for semi-static, static or
commercial use.
We recommend a trial run before using your awning for the first time. This will
allow you to familiarise yourself with the awning, its set up and any limitations
the awning may have for your particular use. Please also check your caravan
awning rail to ensure that it is not damaged or has any sharp edges that could
damage your awning.

3
1
Awning flysheet 1
Hand pump 1
Peg bag 1
Draught skirt 1
Carry bag 1
If you are missing any parts please contact your supplying dealer.
Before using for the first time please check the contents of your awning
SITING
Choose a site that is flat and, if possible, protected from the wind. Sloping
ground may have an adverse affect on your finished awning.
SET UP
To protect your awning from dirt and damage, it may be beneficial to lay a
groundsheet or awning carpet down before unpacking. Unpack the awning,
separate and identify the different parts.
Slide (1) the awning beading, on the rear of the awning roof, through the
caravan awning channel until it is in your required position. The awning should
be positioned on a horizontal part of the caravan.
Peg the webbing strap rear corners of the awning (2). Each corner should be
pegged under the caravan to pull the awning as close to the caravan as
possible. The Fiesta walls are designed to flare out a little.
2
4
Locate the deflation valves at each end of the
main arched AirPole (3). Ensure that the valves
are closed by turning the taps to a 90° angle (as
shown).
Locate the inflation valve on the awning.
Ensure that the valve is screwed tightly into the
AirPole by turning the outer ring (4).
3
4
5
IMPORTANT
It is important that whilst turning
this ring that the valve does not
spin in the AirPole, you can prevent
this from happening by holding the
valve in place where it meets the
AirPole. In picture (4) the left hand
is holding the valve in place. If the
valve spins it will twist the inflation
tube in the pole and may lead to
premature failure. If you suspect
this has happened do not inflate
your awning before untwisting the
tube. Unscrew the valve from the
AirPole and check that the inflation
tube is not twisted. Before
replacing the valve ensure that the
black sealing washer is in place (5).
It is not normally necessary to
remove this valve in day to day use.
WARNING
NEVER OPEN THE ZIP ON THE
GREY INNER TUBES WHILST THE
POLES ARE INFLATED. THIS
WILL RESULT IN THE POLE
BURSTING.

5
Unscrew the top cap, of the inflation valve, and
attach the pump nozzle (6). Start to pump (7).
It is not possible to over inflate the awning with
the pump supplied. An ideal inflation pressure
will be between 9 -11 psi (0.62 - 0.76 BAR), but
do not worry about the pressure when using a
Kampa supplied pump as they can not
physically over inflate the awning. Pump as
much air as you can.
Once the poles have inflated it will be necessary
to lift the front of the awning (8) so that it
assumes the correct shape (9).
Give the awning a few more pumps until the
poles feel hard to the touch. As mentioned
before, an ideal pressure will be between 9-11
psi (0.62 - 0.76 BAR). If necessary take a rest
before adding more pressure.
Close all doors and entrances. Peg the front
corners (10) ensuring that you pull the awning
forward away from the caravan and the front
corners away from each other to create some
tension between them.
Make sure that the awning is sitting squarely on
your caravan, if necessary adjust the pegging at
the four corners ensuring that the sides and
front are stretched tight.
The pegging points have a range of possible
pegging options. Select a point that puts the
awning under tension but without over stressing.
Peg the intermediate pegging points. Once
completed the awning should look taut without
too many creases - if necessary readjust the
pegging and if the poles are bent increase the
pressure.
Once you are happy with the pressure screw on
the inflation point cap until it is tight to prevent
leakage.
6
7
8
10
9
6
GUY LINES
The Fiesta comes with guy lines pre-attached.
We recommend that these guy lines are used at
all times (11). Peg the guy lines so that the
awning is under tension without distorting the
shape, they should run in line with the seams.
The guy lines can be adjusted using the runners.
Guy lines should be secured using suitable pegs
- see above. DO NOT allow children to play
around your awning. Guy lines are a trip hazard.
PEGS
The awning comes complete with general
purpose pegs. These will be suitable for many
sites but there will be some instances where
different pegs will be necessary. Your dealer will
stock a range of pegs suitable for different types
of ground. For maximum effectiveness, pegs
should be driven into the ground at a 45° angle
away from the pegging point. CAUTION: Pegs
can be sharp. Do not allow children to play
around the awning and ensure that suitable
protective footwear is worn.
SEALING BUMPER PADS
To help create a seal between caravan and
awning the Fiesta has sealing bumper pads (12)
sewn to the rear panels. Using the rear pegging
points, these bumpers should be pulled towards
the caravan. An improved seal can be
maintained by use of the optional rear upright
pole set. Insert the top of each pole into the
pocket in the top rear corner, adjust the height to
bring the pole under tension and then secure the
pole to the bumper pads using the tie tapes.
DRAUGHT SKIRT
The supplied draught skirt should be pulled
through the awning rail at the bottom of your
caravan (13). The ropes at the top corners can
be tied to the caravan chassis to make the skirt
taut.
WINDOW BLINDS
The Fiesta Air has blinds to cover each window.
The blinds can be rolled downwards and secured
using the tie tapes supplied.
12
13
14
11

7
MUD SKIRT
The Rally Air comes with an internal mud skirt to
keep out draughts. You can lay your carpet or
groundsheet on top of this skirt.
STORM TIE DOWN KIT (OPTIONAL EXTRA )
For extra security a Storm Tie Down Kit is
available. Attach each tie down to the side
release buckle already sewn to the awning. At
the other end of the tie down you will find a metal
‘D’ ring. Attach the
hook, connected to the
tension band, to the ‘D’
ring and then peg the
tension band using the
large peg supplied or
another suitable peg
(15). Ensure that the
storm strap is pegged
under tension but not
so that it distorts the
shape of the awning.
The tie downs should
always be used in
pairs.
15
DEFLATION
To pack away the awning:
1. Ensure that all the interior isolation valves are open.
2. Close all doors and openings.
3. Close all window blinds.
4. Un-peg the guy lines and, if fitted, the tie down kit.
5. Un-peg the intermediate pegging points but keep the four corners in place.
6. Open the deflation valve on the main pole. The awning will start to deflate.
Wait until most of the air has been expelled.
7. Un-peg the four corners and slide the awning out of the awning rail.
8. Using two people, hold the awning at the tie down attachment points and lay
the awning down on the ground so that the outside of the roof is on the
ground and the front windows are upwards on top of the roof. Protect the
awning from dirt and damage, if necessary, before laying on the floor. Fold
each end inwards to create a rectangle. Roll the awning towards the
deflation valve to expel more air and then roll to fit in the carry bag.
9. Ensure that the awning is totally dry before storing in a cool, dry, dark space:
if possible opened out.
8
SEAMS
The main seams of this awning have been factory taped to help prevent
leakage. Depending upon your expectations, it may be necessary to treat the
remaining seams with a seam sealant. Seam sealant should also be applied to
areas where the taping is damaged or has peeled away through wear and tear.
It can also be applied to areas where a leak may have developed. Seam
sealant is available from your dealer. The awning beading is sewn to the awning
with a special waterproof sewing thread. This thread swells when wet to fill the
needle holes but thread needs to become wet several times before it is totally
effective. This is known as ‘weathering’.
UV DEGRADATION
Awning fabrics can be weakened by prolonged exposure to sunlight. Under
normal holiday use your awning will give long service but use for extended
periods in strong sunlight will soon cause deterioration. In those cases it would
be wise to use a site as shaded as possible. UV degradation is not covered
under the warranty. The warranty does not cover awnings used on permanent
sites, displays or for commercial purposes.
CONDENSATION
Under certain conditions awnings will be affected by condensation inside. See
page 2 for more information about condensation. Condensation and its effects
are not covered under the warranty.
SAFETY
DO NOT COOK IN THE AWNING OR USE NAKED FLAMES. READ AND
UNDERSTAND THE FIRE PRECAUTIONS LABEL SEWN INTO THE INSIDE
OF THE AWNING.

9
PROBLEM SOLUTIONS Difficulty in pumping up the awning. 1. The inflation valve is not fully screwed into the AirPole.
2. The dump (deflation) valves are open. Close. 3. The inflation tube is twisted at the valve. This may also be indicat-
ed by a noise. DO NOT continue to inflate until the tube has been untwisted (see page 3).
Part of the awning does not inflate 1. The isolation valves that connect the AirPoles may not be open.
Open the valve and the air will flow into the poles. Do not close the vales during normal use.
Part of the awning does not deflate 1. An isolation valve may have been closed. Locate and open. If you suspect an air leak 1. Check that the inflation valve is properly closed and that the black
‘O’ ring seal is in place.
2. Check that the top cap on the inflation valve is done up tightly 3. Check that all the deflation valves are closed
If you still suspect an air leak 1. Close all the isolation valves in the awning. Wait for a while and
then check each AirPole for pressure. If there is reduced pressure in any AirPole Check the connecting hoses to make sure that the compression fittings are done up tightly. If you still suspect a leak it will be necessary to investigate the individual AirPole. See the AirPole repairing and changing section of this manual.
TROUBLESHOOTING
10
PROBLEM SOLUTIONS If you think your awning has a water leak 1. Most suspected leakage is actually condensation (see
condensation section of this manual). This forms on the inside of the awning fabric. Try to increase the ventilation by opening the doors. A waterproof groundsheet will help stop moisture from the ground causing condensation. The fabric, used to make this awning, has a massive hydrostatic head, so it is extremely unlikely that it would leak.
If your awning has a water leak at specific points/areas
1. The main seams of this awning have been factory taped to help
prevent leakage. Depending upon your expectations, it may be necessary to treat the remaining seams with a seam sealant. Seam sealant should also be applied to areas where the taping is damaged or has peeled away through wear and tear. It can also be applied to areas where a leak may have developed. Kampa seam sealant is available from your dealer.
If you think your awning has a water leak at the beading that attaches to the caravan
1. It is not possible to hot air tape the join between the awning and
the caravan beading. Therefore we use a special waterproof sewing thread. This thread swells when wet to fill the needle holes but the thread needs to become wet several times before it is totally effective. This is known as ‘weathering’.

11
IN THE EVENT OF A PUNCTURE
If you suspect a puncture follow the following procedure:
Close all the isolation valves in the awning. Wait for a while and then check
each AirPole for pressure. If there is reduced pressure in any AirPole check the
connecting hoses to make sure that the compression fittings are done up tightly.
If you still suspect a leak it will be necessary to investigate the individual AirPole.
If tightening the hose fittings does not solve the problem then the AirPole may be
punctured.
TO REMOVE AN AIRPOLE
You can remove an AirPole when the awning is inflated or deflated but if it’s
inflated the isolation valves around the pole must be closed.
NEVER OPEN THE ZIP ON THE GREY INNER TUBES WHILST
THE POLES ARE INFLATED
Unzip the sleeve holding the AirPole.
 Undo the compression fittings on the punctured pole side of the isolation
valve. There may be one or two per pole.
 You should now be able to remove the AirPole
 Unzip the protective cover of the AirPole to expose the inflatable tube.
NEVER UNDO THE ZIP IF THE TUBE IS UNDER PRESSURE
 Locate the puncture. This is made easier if you blow some air into the tube.
For small holes it may be necessary to submerge the inflatable tube in water.
 Once located the tube can be repaired using repair tape. We recommend
the following:
 Kampa Awning & Tent Repair Tape
The repair can be enhanced by using a combination of one of the above with
one of these flexible adhesives:
 Kampa Repair Solution
10. Follow the manufacturers instructions to repair.
11. Another alternative is to replace the tube. Spares are available from your
dealer or direct from Kampa.
12. Reassemble the AirPole, zip back into the sleeve and reconnect the hose/s
to the isolation valve/s.
12
CARE
Awnings are best stored opened out. Air fully and ensure it is totally dry before
packing away. Store in a well ventilated dry place. A wet/damp awning will
develop mildew surprisingly quickly. Dirty awnings can be washed using clean
water and a soft brush. Do not scrub and never use detergents.
The AirPoles do not need any maintenance but should be protected from
damage during storage. Damage due to improper use, wind damage or neglect
is not covered under the warranty. Have any damage repaired at the first
opportunity.
Zips should be treated with care, use two hands to close and open and never
tread on them. Never force a zip. We strongly recommend that you carry a
comprehensive spares kit including silicone waterproof spray, seam sealer and
tape for repairing the AirPoles.
Repairs to the flysheet should be made by a company recommended by Kampa
or your supplying dealer. Repairs and alterations made by an unauthorised
company may invalidate your warranty.
OPTIONAL EXTRAS AVAILABLE FOR YOUR FIESTA AWNING
 Continental Cushioned Carpet - custom made to fit your awning
 Easy Tread Carpet - custom made to fit your awning
 Annexe - can be fitted either side of the awning. Complete with inner tent.
(Fiesta AIR Pro only)
 Storm Tie Down kit - for extra security in strong winds
 Rear Upright Pole Set - gives an improved seal against
your caravan
 Hanging Rail - fits the built in AccessoryTrack® (Fiesta
AIR Pro only)
 Awning Organiser - fits the built in AccessoryTrack®
(Fiesta AIR Pro only)
 Roof lining - insulates the roof in hot and cold weather
(Fiesta AIR Pro only)
Kampa also produces an extensive range of awning furniture
designed to complement your awning.
Kampa UK Limited
Witham, CM8 3EU © mcl/Kampa/2015